Oki MC160MFP Maintenance Manual page 200

Oki Data CONFIDENTIAL
Code
0046 Receive incorrect signal when sending RNR which response with ERR signal.
0047 Can not receive correct signal after sending ERR signal.
0048 Can not receive correct signal after receive PPS_PRI_Q or PRI_Q, EOR_PRI_Q.
0049 Can not receive correct signal after sending PIP/PIN signal within 13 sec.
Line energy over threshold last 60 sec. after MCF, and can not detect FSK or carrier signal
004A
in ECM mode.
004B Can not detect correct FSK signal even through detected FSK tone within 6 sec.
Handshake fail during re-train or between page in V.34 RX.
004C
Receive DCN signal after sending DIS in V.34.
004E
Remote side disconnected after sending ANSam in V.8 phase.
004F
Can not receive any correct signal after sending CJ signal in V.8 phase.
0050
Can not receive phase 3 signal after phase 2 within 20 seconds in V.34.
0051
Can not receive phase 4 signal after phase 3 within 20 seconds in V.34.
0052
Modem disconnect after phase 4 in V.34.
0053
Remote side disconnected after phase 4 in V.8.
0054
Receive incorrect signal after sending DIS signal in V.34.
0055
Modem disconnect after sending CFR in V.34.
0056
0057 Can not detect image signal within 6 seconds after sending CFR.
Can not detect image signal within 6 seconds after modem enter to primary phase in V.34.
0058
005A Modem can not detect any correct ECM frame with 3 minutes in phase C.
005B Can not detect phase 5 signal after primary channel within 6 seconds.
005C Detect busy tone within control channel after phase C.
005D Modem can not detect any correct ECM frame with 12 sec. in phase C.
005E Can not detect control channel signal after received RCP frame within 6 seconds.
005F Can not detect silence after sending JM signal for polling TX function.
There are no any bulletin files to be polled in V.34.
0060
Machine can not detect V.21 or V.8 signal with 35 seconds.
0061
0062 Modem disconnect in phase D after our side sending out flags sequence in control channel.
0063 Can not receive any flag sequence in control channel within 6 seconds in phase D.
Can not detect any control channel signal in phase D within 60 seconds even through
0064
energy still on the line.
0065 Can not detect any control channel signal within 60 seconds after detect silence in phase D.
Can not receive T.30 signal or carrier after sending CFR in V.34.
0066
0070 User press stop key within receiving.
0071 Memory full within receiving.
0072 Received EOR_Q Signal.
44292401TH Rev.1
Possible Causes of Error.
21.4.2 Transmission
20.4.2 Transmission
Code Possible Causes of Error.
0080 Can not detect any G3 signal within 35 sec. specified by ITU-T in phase B.
0081 Received DTC signal in transmission phase.
0082 Transmitting unit receives a signal other than DIS or DTC and DCN in phase B.
0083 Detected FSK signal, but can not receive any signal within 35 seconds.
0084 Detect DCN signal in phase B.
0085 Transmitting unit sending DCS 3 times consecutively, but each time responds with DIS/DTC.
0086 Detected responds signal other than DTC, DIS, FTT, DCN or CFR after sending DCS.
0087 Training attempt has failed because speed unit can not adjust to low lower speed.
0088 Received DCN signal after sending out DCS signal.
008B Receiver's protocol of DIS is received, but it is not compatible with our machine.
Receiver's protocol of DIS is received, but remote side can not receive document temporary,
008D
may be cause by run out of paper or other reason.
008E Remote side CSI number not defined in machine one touch or speed dial directory.
Modem not ready to received V.34 data within 6 seconds after received CFR signal.
008F
0090 Called side document not ready for our polling.
0091 Sending out DCS+TCF signal 3 times consecutively but no signal in response from receiver.
0092 Remote side disconnected within transmitting phase.
Received DCN signal after sending out DCS signal for V.34.
0093
0094 Time out during transmit ECM frame or RCP command.
0095 Wrong ID number when Polling RX.
0099 Remote side disconnect after primary channel.
009A Can not detect any signal after sending CI signal.
Received DCN after sending DTC in V.34 polling RX.
009C
Remote side hang up before V.34 modem enter phase 2 state in V.34 polling RX.
009D
009F Can not received any response from other side after sending PPS_EOM signal.
00A0 User stop or cancel transmission job.
00A1 Document JAM within transmission.
Can not finished V.8 procedure or detect V.21 signal after CM signal within 30 seconds.
00AE
Modem can not enter into control channel after TX side sending out RCP signal for V.34.
00AF
Can not received any command after our side retry there DCS signal in V.34 TX.
00B0
Can not finish V.8 procedure or detect V.21 signal after ANSam signal within 35 seconds.
00B1
00B2 Can not detect phase 2 signal after our side sending CJ signal within 30 seconds.
Can not detect correct V.21 or JM signal after sending CM signal.
00B3
00B4 Can not detect correct phase 2 signal within 25 second after CM/JM signal exchange.
00B5 Can not detect phase 3 signal after phase 2 within 25 seconds.
00B6 Can not detect phase 4 signal within 25 seconds after CM/JM exchange.
00B7 Can not detect phase 5 signal after phase 4 within 30 seconds.
Remote side disconnect after our side sending DCS signal in V.34.
00B8
Receive T.30 signal other than DIS, DCS, CFR after sending DCS signal in V.34.
00B9
Can not received correct signal after our side sending DTC signal in V.34.
00BA
Every time our side received DIS signal after sending DTC in V.34.
00BB
TROUBLESHOOTING
199 /