Instrument Lights; Ash Tray Lights; Glove Compartment Light; Map Light - Lincoln Continental 1964 Shop Manual

(285)
PART 15-2-LIGHTING SYSTEM A.ND HORNS 15-9
------------------------------
lens and socket from the bracket.
5. Remove the bulb from the
socket.
INSTRUMENT LIGHTS
The instrument panel lights and
wiring are shown in Fig. 7.
1.
Disconnect the battery.
2. Remove the radio control knobs
and remove the radio control lock
nuts and washers.
3. Remove the knobs from the
heater and air conditioner controls
and the heater and air conditioner
blower switch.
4. Remove the 10 screws retaining
the center instrument panel bezel
and remove the bezeL
5. Replace the light bulb.
6.
Position the center instrument
panel bezel and install
th~
I 0 retain-
ing screws.
7. Install the knobs on the heater
and air conditioner controls and the
heater and air conditioner blower
switch.
8.
Install the washers and lock nuts
in the radio control parts.
9. Install the radio control knobs.
10. Connect the battery.
ASH TRAY LIGHTS
Ash tray lights arc provided with
the ash trays on the instrument panel
and in the rear compartment. To
replace the bulb, remove the ash
tray.
GLOVE COMPARTMENT LIGHT
The glove compartment light is
located in the upper left corner of
the glove box. To replace the bulb,
remove tlJe two retaining screws and
remove the bulb-type lens.
MAP LIGHT
The map light is shown in Fig. 8.
To replace the bulb, remove the two
lens retaining screws and remove
the lens.
COURTESY LIGHTS
Courtesy lights arc located on the
right and left rear quarter trim panel.
Remove the bezel from the trim
panel to replace the bulb.
LUGGAGE COMPARTMENT
LIGHT
1. Remove the screw retaining the
bracket and light assembly to the
rear deck lid. Remove the bracket
and light assembly and the lock
washer.
2. Replace the bulb.
3. Position the lock washer be-
tween the bracket and the rear deck
lid and install the bracket and light
assembly with the retaining screw.
LOW FUEL WARNING LIGHT
1. Remove the lower
instrumc~nt
panel.
2. Remove the fuel gauge, but do
not remove the gauge from the dual
gauge mounting plate.
3. Remove the light bulb from the
instrument panel at the fuel gauge
mounting area.
4. Install the new light bulb in the
instrument panel.
5. Install the fuel gauge.
6. Install the lower instrument
panel.
IGNITION SWITCH LIGHT
1. Disconnect the battery.
2. Turn the ignition key to the
accessory position. Slightly depress
the pin shown in Fig. 5, Part 15·-3,
turn the key counterclockwise and
pull the key and lock cylinder out
of the switch assembly.
3. Press in on the rear of the
switch to depress the spring and ro-
tate the swtich Vs turn counterclock-
wise (as viewed from the terminal
end). Remove the switch from the
iower instrument panel.
4. Remove the light and bracket
a.;;scmbly from the underside of the
instrument panel for accessibility.
5. Replace the light bulb.
6. Position the switch to the light
and bracket assembly.
7. Place the switch in the switch
opening, press the switch toward the
instrument panel, and rotate the
switch 1 /x turn to lock it in position.
8. Turn the key in the lock cylin-
der to the accessory position. Place
the lock and key in the ignition
switch, depress the pin slightly (Fig.
5, Part 15-3), and turn the key
counterclockwise. Push the lock cyl-
inder into the switch. Turn the key
FIG.
8-Map Light
to check the lock cylinder operation.
9.
Connect the battery.
HORNS
The horns are mounted to the
right front fender apron in the en-
gine compartment. Disconnect the
horn wire from the terminal. Remove
the horn bracket to fender apron re-
taining screws and remove the horns.
To install, place the horns in posi-
tion and install the retaining screws.
Install the horn wire.
HORN RING
1. Disconnect the battery.
2. Remove the center steering
wheel cover.
3. Remove the two retaining screws
in the center of the steering wheel
and the one screw retaining the three
horn wires.
4. Remove the three screws under
the steering wheel which retain the
horn ring and remove the horn ring.
5. Position the horn ring and in-
stall the three retaining screws under
the steering wheel.
6. Install the two retaining screws
in the center of the steering wheel,
and the one screw retaining the
three horn wires.
7. Install the center steering wheel
cover.
8. Connect the battery.
HORN RELAY
The horn relay is mounted on the
right-hand cowl side panel.
1. Disconnect the battery ground
cable from the battery.
2. Remove the six bolts retaining
the stone shield to the right front
fender and remove the stone shield.
3. Disconnect the wire connector
from the relay.
4. Remove the three screws hold-
ing the relay mounting bracket and
pull out the bracket and relay.
5.
Remove the nut and bolt retain-
ing the horn relay to the mounting
bracket and remove the relay.
6. Position the relay to the mount-
ing bracket and install the bolt and
nut.
7. Position the relay and bracket
assembly and install the three retain-
ing screws.
8. Connect the wire connector to
the relay.
9. Position the stone shield under
the fender and install the six retain-
ing bolts.
10. Connect the battery and check
the operation of the horn.