1. Manuals
  2. Brands
  3. Lincoln Manuals
  4. Automobile
  5. 2001 Lincoln Town Car
  6. Owner's manual

Lincoln 2001 Town Car Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
www.carburetor-manual.com
Would you like some Free Manuals?
http://carburetor-manual.com/free-shop-manual-club-t-13.html
Also visit
http://freeshopmanual.com
for more Free Manuals
Also Visit my website for 7 FREE Download Manuals starting
with this one.
"The ABC's of Carburetion"
Click Here Now
file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]

Advertisement

Table of Contents
loading

Related Manuals for Lincoln 2001 Lincoln Town Car

Summary of Contents for Lincoln 2001 Lincoln Town Car

  • Page 1 www.carburetor-manual.com Would you like some Free Manuals? http://carburetor-manual.com/free-shop-manual-club-t-13.html Also visit http://freeshopmanual.com for more Free Manuals Also Visit my website for 7 FREE Download Manuals starting with this one. "The ABC's of Carburetion" Click Here Now file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]...
  • Page 2 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.

  • Page 3: Introduction

    Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
  • Page 4 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. EMISSION WARRANTY The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L...
  • Page 5 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Tether Warning Anchorage Brake System Anti-Lock Brake System Brake Fluid - Traction Control...
  • Page 6 Introduction Vehicle Symbol Glossary Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid Power Steering Fluid Level Emission System...

  • Page 7: Instrumentation

    Instrumentation Panel dimmer switch (pg. 25) Instrument cluster (pg. 8) Gearshift lever Headlamp control (pg. 135) (pg. 25) CHECK WASHER CIRCLE FUEL ECON LTR/100km SLOWLY DIST TO EMPTY AVG SPEED TRIP A B O/D OFF TRAC ACTIVE km MILES/GAL SPEED CONTROL COMPASS <...
  • Page 8 Instrumentation Audio system (pg. 33) Clock* (pg. 58) BASS TREB FADE PUSH ON TAPE SCAN AUTO SEEK TUNE SIDE 1 2 COMP SHUFF SELECT RESET FRONT REAR AUTO Climate control system (pg. 27) Electronic sound system controls* (pg. 65) * if equipped...

  • Page 9: Warning Lights And Chimes

    Instrumentation WARNING LIGHTS AND CHIMES CHECK FUEL TRUNK AJAR DOOR AJAR WASHER CIRCLE FUEL ECON LTR/100km TRAC OFF AIR SUSPENSION SLOWLY DIST TO EMPTY AVG SPEED TRIP A B O/D OFF TRAC ACTIVE km MILES/GAL SPEED CONTROL COMPASS < FILL ON LEFT km/h SERVICE...
  • Page 10 Instrumentation 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Service Engine Soon light should turn off.
  • Page 11 Instrumentation Check fuel cap Momentarily illuminates when the CHECK ignition is turned to the ON position FUEL to ensure your bulb is working. When this light turns on, check the fuel filler cap. Continuing to operate the vehicle with the check fuel cap light on, can activate the Service Engine Soon/Check Engine warning light.
  • Page 12 Instrumentation Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb. Refer to Bulbs in the Maintenance and care chapter. High beams Illuminates when the high beam headlamps are turned on.
  • Page 13 Instrumentation Engine coolant temperature Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as safely possible, switch off the engine and let it cool. Never remove the coolant recovery cap while the engine is running or hot. Refer to Engine coolant in the Maintenance and care chapter.
  • Page 14 Instrumentation Trac off Illuminates when the Traction TRUNK AJAR DOOR AJAR Control system has been disabled CIRCLE (by the driver or as a result of a TRAC OFF AIR SUSPENSION SLOWLY system failure). For more information, refer to the Driving chapter.
  • Page 15 Instrumentation Trac active Illuminates when the Traction TRUNK AJAR DOOR AJAR Control system begins applying and CIRCLE releasing the brakes and adjusting TRAC OFF AIR SUSPENSION SLOWLY the engine characteristics to limit a wheelspin condition. For more information on the traction control O/D OFF TRAC ACTIVE system, refer to the Driving...

  • Page 16: Headlamps On Warning Chime

    Instrumentation Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter. Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened. Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is opened.
  • Page 17 Instrumentation Odometer Registers the total kilometers TRUNK AJAR DOOR AJAR (miles) of the vehicle. CIRCLE TRAC OFF AIR SUSPENSION SLOWLY O/D OFF TRAC ACTIVE SPEED CONTROL COMPASS Fuel gauge Displays approximately how much < FILL ON fuel is in the fuel tank (when the LEFT key is in the ON position).
  • Page 18 Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
  • Page 19 Instrumentation • see how many kilometers/miles WASHER FUEL ECON you can drive before running out LTR/100km DIST TO EMPTY of fuel. AVG SPEED • see how many liters/gallons of TRIP A B fuel remain in the fuel tank. • monitor the average fuel km MILES/GAL economy.
  • Page 20 Instrumentation Compass display (if equipped) The compass reading may be TRUNK AJAR DOOR AJAR affected when you drive near large CIRCLE buildings, bridges, power lines and TRAC OFF AIR SUSPENSION SLOWLY powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also O/D OFF TRAC ACTIVE affect compass accuracy.
  • Page 21 Instrumentation Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Locate the compass module and the calibration button mounted on the center rear view mirror post. 3. Turn ignition to the ON position. 4.
  • Page 22 Instrumentation 3. Press and hold the CALIBRATION TRUNK AJAR DOOR AJAR BUTTON for 2 to 4 seconds until CIRCLE CIRCLE SLOWLY is displayed on the TRAC OFF AIR SUSPENSION SLOWLY message center. 4. Release pressure from the button. O/D OFF TRAC ACTIVE 5.
  • Page 23 Instrumentation You may notice gradual improvement in fuel economy over the course of your vehicle’s break-in period (approximately 1 600 kilometers [1 000 miles]). 1. Set the speed control. Refer to Speed control in the Controls and features chapter. 2. Select FUEL ECON FUEL ECON DIST TO EMPTY AVG SPEED...
  • Page 24 Instrumentation Dist to empty (DTE) This function estimates FUEL ECON approximately how far you can drive DIST TO EMPTY with the fuel remaining in your tank under normal driving conditions. AVG SPEED Remember to turn the ignition OFF TRIP A B when refueling your vehicle.
  • Page 25 Instrumentation Trip A B These two functions allow you to FUEL ECON see how far you have traveled since DIST TO EMPTY you last reset. Trip A and Trip B are completely independent and must AVG SPEED be reset individually. TRIP A B To reset either trip feature to zero, SELECT...

  • Page 26: Controls And Features

    Controls and features PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight PANEL and parklamp operation. • Push up to brighten. • Push down to dim. AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
  • Page 27 Controls and features Daytime running lamps (DRL) (if equipped) The daytime running light system turns the headlamps on, with a reduced light output, when: • the ignition is in RUN, • the transmission is not in P (Park), and • the headlamp system is not turned on by another feature such as using the headlamp control or Autolamp.
  • Page 28 Controls and features CLIMATE CONTROL SYSTEM Electronic Automatic Temperature Control (EATC) system The EATC system will maintain a FRONT selected temperature and automatically control airflow. You REAR can override automatic operation AUTO with any of the override controls, the fan speed control or steering wheel controls.
  • Page 29 Controls and features In approximately 3 ⁄ minutes or less, the fan speed will start to increase and the airflow location will change to the floor area. If unusual conditions exist (i.e.-window fogging, etc.), the manual override controls allow you to select airflow locations and the fan control allows you to adjust fan speed as necessary.
  • Page 30 Controls and features Fan speed ( When AUTO is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, press the fan control to cancel automatic fan speed operation or use the steering AUTO wheel fan speed control.
  • Page 31 Controls and features • (Panel)-Distributes outside air through the instrument panel registers. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode. • (Panel and floor) -Distributes outside air through the instrument panel registers and the floor ducts.
  • Page 32 Controls and features Displaying outside temperature Press EXT to display the outside air temperature. It will be displayed until EXT is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for AUTO four seconds after it is changed, then the outside temperature will...
  • Page 33 Controls and features • If your vehicle has been parked with the windows closed during warm weather conditions, the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle.
  • Page 34 Controls and features REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. FRONT Press the rear defroster control to clear the rear window of thin ice REAR and fog. • A small LED will illuminate when the rear defroster is activated.
  • Page 35 Controls and features Volume/power control Press the control to turn the audio VOL - PUSH ON system on or off. Turn the control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
  • Page 36 Controls and features Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next SEEK frequency down the band (whether or not a listenable TUNE station is located there). Hold the control to move through the frequencies quickly.
  • Page 37 Controls and features Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
  • Page 38 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. FADE Tape select • To enter tape mode while in radio mode, press the TAPE AMS control.
  • Page 39 Controls and features Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection. TAPE To activate the feature, momentarily depress the TAPE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection).
  • Page 40 Controls and features Eject function Press the control to stop and eject a tape. Dolby noise reduction Dolby noise reduction operates only in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction.
  • Page 41 Controls and features To set the minute, press and hold the CLK control and press: TAPE • to decrease minutes and SEEK SEEK • to increase minutes. TUNE TUNE The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time).
  • Page 42 Controls and features Premium AM/FM Stereo/Cassette (CD Changer Compatible) BASS TREB FADE PUSH ON TAPE SEEK TUNE SCAN AUTO MUTE SIDE 1 . 2 COMP SHUFF Alpine Audio System with AM/FM Stereo Cassette (CD Changer Compatible) BASS TREB FADE PUSH ON TAPE SEEK TUNE...
  • Page 43 Controls and features individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off. Your vehicle is equipped with a delayed accessory feature.
  • Page 44 Controls and features With the radio on, press and hold the volume control for five seconds, until the display reads SPEED VOL, then press: PUSH ON • to increase volume compensation • to decrease or shut off the volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if...
  • Page 45 Controls and features Tune adjust in radio mode • Press to move to the next TUNE frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there).
  • Page 46 Controls and features Seek function for CD changer • Press to seek to the previous SEEK track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning.
  • Page 47 Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
  • Page 48 Controls and features Treble adjust The treble adjust control allows you to increase or decrease the audio BASS system’s treble output. Press the TREB control. Use the TREB SEL control to increase or decrease the amount of treble. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
  • Page 49 Controls and features Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached.
  • Page 50 Controls and features Dolby noise reduction Dolby noise reduction operates only in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction. The Dolby noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation.
  • Page 51 Controls and features Radio data system (RDS) feature This feature allows your audio system to receive station identification or program type from RDS-equipped FM radio stations. The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information.
  • Page 52 Controls and features • Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz •...
  • Page 53 Controls and features Phone mode This feature allows you to control the factory-installed cellular phone (if equipped) through the radio MUTE controls. • Press the phone/mute control to enter phone mode. The playing media will mute. • Use SEEK, TUNE or radio presets 1 through 6 to select a phone number previously programmed in the phone.
  • Page 54 Controls and features Press the DSP control until one of the following appears: • ALL SEATS • DRIVER SEAT • REAR SEATS Use the SELECT control to change the equalization to the desired mode. Setting the clock with radio data system (RDS) feature (if equipped) This feature applies to vehicles not equipped with a separate, instrument panel mounted clock.
  • Page 55 Controls and features 2. Press to eject the magazine. 3. Pull the lever to remove a CD tray from the magazine. 4. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing If you pull too hard on the disc holder, the disc holder may come completely out of the magazine.
  • Page 56 Controls and features 6. Insert the CD magazine into the changer. 7. Slide the door to the left to close. Use only compact discs containing this mark. The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer.
  • Page 57 Controls and features • The disc is dusty or defective. • The player’s internal temperature is above 60°C (140°F). Allow the player to cool down before operating. • A disc with format and dimensions not within industry standards is inserted. Cleaning compact discs Inspect all discs for contamination before playing.
  • Page 58 Controls and features Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area.
  • Page 59 Controls and features CLOCK (IF EQUIPPED) If your vehicle is not equipped with an instrument panel mounted clock, refer to Setting the Clock section in this chapter. Press the right control to increase the time displayed. Press the left control to decrease the time displayed.
  • Page 60 Controls and features AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not BASS TREB FADE PUSH ON hang any type of accessory or TAPE SEEK SCAN AUTO TUNE MUTE accessory bracket from the plug. SIDE 1 2 COMP SHUFF Improper use of the power...
  • Page 61 Controls and features KEYS The vehicle is equipped with a master key and valet key lock system. The master key will access doors, trunk, glove box, ignition and remote trunk release. The valet key (marked “valet”) will access doors and ignition only.
  • Page 62 Controls and features WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
  • Page 63 Controls and features SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on.
  • Page 64 Controls and features If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill.
  • Page 65 Controls and features • Depress the brake pedal. When the desired vehicle speed is reached, press SET ACCEL. ACCEL COAST To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
  • Page 66 Controls and features To return to a previously set speed • Press RES/RESUME. For RES/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). ACCEL COAST Indicator light Indicator message This message is displayed in the SPEED CONTROL Message Center when either the SET ACCEL or RES/RESUME...
  • Page 67 Controls and features In Tape mode: • Press MEM/NEXT to listen to the next selection on the tape. In CD mode: • Press MEM/NEXT to listen to the next track on the disc. In any mode: • Press VOL up or down to adjust the volume. Climate control features •...
  • Page 68 Controls and features HOMELINK UNIVERSAL TRANSCEIVER (IF EQUIPPED) The HomeLink Universal Transceiver, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most current transmitters to operate garage doors, entry gates, security systems, entry door locks, and home or office lighting.
  • Page 69 Controls and features 3. Using both hands simultaneously press and hold the hand-held transmitter button and the desired HomeLink button. Do not release the buttons until step 4 has been completed. Some entry gates and garage door openers may require you to replace step 3 with the procedure in the “Canadian Programing”...
  • Page 70 Controls and features Operating the HomeLink Universal Transceiver Once programmed, the HomeLink Universal Transceiver can be used in place of hand-held transmitters. To operate, simply press and release the appropriate HomeLink button (the red light will illuminate, indicating the signal is being transmitted).
  • Page 71 Controls and features 3. Press and release the programmed HomeLink button. Press and release the HomeLink button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training.) The 2nd or 3rd press from step 3 will activate the door.
  • Page 72 Controls and features MOON ROOF (IF EQUIPPED) To open the moon roof: • Press and release the control. • For one-touch operation, press and release the rear portion of the control; this will fully open the moon roof. • To stop one-touch operation at the desired position, press and release the forward portion of the control.
  • Page 73 Controls and features Do not block the sensor on the backside of the mirror since this may impair proper mirror performance. COMP MIRROR Ensure the mirror is pulled down low enough to prevent visibility interference with the moon roof controls. The mirror support arm has two pivot points which lets you adjust the mirror UP or DOWN and from SIDE to SIDE.
  • Page 74 Controls and features Fuel filler door override release If the remote release is inoperative, open the trunk, then pull the override release handle located inside the trunk to open the fuel filler door. POWER WINDOWS Express down To make the driver window open WINDOW LOCK fully without holding the window control, press the top portion of the...
  • Page 75 Controls and features Accessory delay (if equipped) With accessory delay, the window switches, radio, and moonroof may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened. POWER DOOR LOCKS Press control to unlock or lock all doors.
  • Page 76 Controls and features Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
  • Page 77 Controls and features MEMORY SEATS/REARVIEW MIRRORS/ADJUSTABLE PEDALS (IF EQUIPPED) This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to three programmable positions. The memory control is located on the driver door. • To program position one, move the driver seat, mirrors, and pedals to the desired position using the controls.
  • Page 78 Controls and features Radio/climate controls Refer to Steering Wheel Controls in this chapter for operation instructions. NEXT MODE Radio/climate controls lockout The rear radio/climate control feature can be locked out by pressing the 3 and the 5 buttons on the radio simultaneously while the radio is on. To enable the rear radio/climate controls, press the 3 and the 5 buttons again.
  • Page 79 Controls and features Move the control forward or backward to move front passenger seat. Remote seat adjustment lockout The window lockout control, located WINDOW LOCK on the drivers door, will also lockout the remote seat adjustment. To lock out the remote seat adjustment feature, press the right side of the control.
  • Page 80 Controls and features POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
  • Page 81 Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. The horn will chirp and the parklamps/taillamps will flash to confirm that the control was...
  • Page 82 Controls and features Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle. Failure to latch the trunk may cause objects to fall out of the trunk or block the rear view.
  • Page 83 Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation.
  • Page 84 Controls and features To reprogram the transmitters yourself, place the key in the ignition and turn from 2 (LOCK) to 3 (OFF) and cycle between 3 (OFF) and 4 (ON) four times in rapid succession within 3 seconds. After doors lock/unlock, press any control on all transmitters (up to four).
  • Page 85 Controls and features Autolock can also be activated or deactivated using the following procedure: You must complete steps 1 through 7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds.
  • Page 86 Controls and features Reactivating the memory seat/mirrors/adjustable pedals feature The remote memory seat/mirrors/adjustable pedals feature comes disabled from the factory. The following sequence will reactivate the transmitter: 1. Press the SET control. 2. Press any control on the remote entry transmitter. 3.
  • Page 87 Controls and features Programming your own entry code 1. Enter the factory-set code (keypad will illuminate when pressed). 2. Press the 1/2 control within five seconds of step 1. 7 8 9 0 3. Enter your personal 5–digit code. Enter each digit within five seconds of the previous one.
  • Page 88 Controls and features Unlocking the doors and releasing the trunk with the keyless entry system To unlock the driver door, enter either the factory-set code or personal code (each digit pressed within five seconds of prior digit). The interior lamps will illuminate. To unlock all doors, enter the factory-set code or personal code 7 8 9 0...
  • Page 89 The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Automatic arming...
  • Page 90 Check to make sure the coded key is an approved Ford coded key. If your keys are lost or stolen you will need to do the following: •...
  • Page 91 Controls and features Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure.
  • Page 92 Controls and features INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle.

  • Page 93: Seating And Safety Restraints

    Seating and safety restraints SEATING Head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
  • Page 94 Seating and safety restraints Press the control to recline the seatback forward or backward. Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down.
  • Page 95 Seating and safety restraints Heated seats (if equipped) The heated seat controls are located on the door trim panel. To operate the heated seats: • Slide the control to BACK to heat BACK the seatback only. • Slide the control to BOTH to heat the seatback and the seat cushion.
  • Page 96 Seating and safety restraints Using the manual recline function (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
  • Page 97 Seating and safety restraints Memory seats/rearview mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to three programmable positions. The memory seat control is located on the driver door. • To program position one, move the driver seat to the desired position using the seat controls.
  • Page 98 Seating and safety restraints • Front crash severity sensor. • Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and back-up tone. • The electrical wiring for the air bags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, passenger occupant classification sensor (if equipped), and indicator lights.
  • Page 99 If your vehicle is equipped with this feature, there will be a label located under the front passenger seat which is marked “OCS”. Alternatively, you may take your vehicle to any Ford or Lincoln Mercury dealer for assistance. For air bags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the air bag when it begins to inflate.
  • Page 100 Seating and safety restraints Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Personal Safety System to tailor the air bag deployment and safety belt pretensioner activation depending upon safety belt usage.
  • Page 101 Seating and safety restraints If any of these things happen, even intermittently, have the Personal Safety System serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision. Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
  • Page 102 Seating and safety restraints Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only.
  • Page 103 Seating and safety restraints The front outboard and rear safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
  • Page 104 This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.
  • Page 105 Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down.
  • Page 106 Seating and safety restraints The lap belt does not adjust automatically. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
  • Page 107 Seating and safety restraints Conditions of operation If... Then... The driver’s safety belt is not The safety belt warning light buckled before the ignition switch illuminates 1-2 minutes and the is turned to the ON position... warning chime sounds 4-8 seconds.
  • Page 108 Seating and safety restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare 36 700 crashes occur every day. The more we events” drive, the more we are exposed to “rare” events, even for good drivers.
  • Page 109 Seating and safety restraints One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
  • Page 110 (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
  • Page 111 This information will assist Ford Motor Company in the servicing vehicle and helping to better understand real world collisions and further improve the safety of future vehicles.
  • Page 112 Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may affect the performance of the air bag sensors increasing the risk of injury.
  • Page 113 Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
  • Page 114 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
  • Page 115 Seating and safety restraints • a readiness light and tone. • diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.
  • Page 116 Do not attempt to service, repair, or modify the air bag supplemental restraint system, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always...
  • Page 117 Seating and safety restraints How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks.
  • Page 118 Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with...
  • Page 119 Seating and safety restraints Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.
  • Page 120 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all applicable Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
  • Page 121 • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
  • Page 122 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
  • Page 123 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
  • Page 124 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
  • Page 125 Seating and safety restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor.
  • Page 126 Seating and safety restraints 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat.
  • Page 127 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
  • Page 128 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the gearshift is in P (Park). 4. Make sure the parking brake is set. 5. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns...
  • Page 129 Starting Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE NOTE: Whenever you start your vehicle, release the key as soon as the engine starts.
  • Page 130 Starting To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately.

  • Page 131: Driving

    Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
  • Page 132 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal BRAKE...
  • Page 133 Driving The BRAKE warning lamp in the BRAKE instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle.
  • Page 134 Driving TRACTION CONTROL For Traction Control warning lights refer to Warning Lights in the Instrumentationchapter. Your vehicle may be equipped with the optional Traction Control system. This system helps you maintain the stability and steerability of your vehicle. It is especially useful on slippery and/or hilly road surfaces. The system operates by detecting and controlling wheel spin.
  • Page 135 Driving STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. To prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
  • Page 136 Driving This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch is located on the left side of the trunk.
  • Page 137 Driving Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern.
  • Page 138 Driving P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift lever is latched in P (Park).
  • Page 139 Driving The transmission control indicator TRUNK AJAR DOOR AJAR light (TCIL) will illuminate on the CIRCLE instrument cluster. AIR SUSPENSION SLOWLY O/D OFF SPEED CONTROL COMPASS Drive Not shown on the display. Activate by pressing the transmission control switch on the gearshift lever with the gearshift in the Drive position. The O/D OFF indicator will illuminate in the instrument cluster.
  • Page 140 Driving 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to Overdrive. Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed.
  • Page 141 Driving • GVWR (Gross Vehicle Weight Rating): Maximum permissable total weight of the base vehicle, occupants, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Certification Label on the driver’s door pillar. •...
  • Page 142 Driving and equipment being carried is within the weight limitations that have been established for your vehicle including both gross vehicle weight and front and rear gross axle weight rating limits. Under no circumstance should these limitations be exceeded. Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury.
  • Page 143 Driving If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications.
  • Page 144 Driving Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. •...
  • Page 145 • Maximum distance is 80 km (50 miles). If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician. See your local dealer for driveshaft removal/installation.

  • Page 146: Roadside Emergencies

    Roadside emergencies Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week •...
  • Page 147 Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside...
  • Page 148 Roadside emergencies The fuel pump shut-off switch is located on a bracket inside of the luggage compartment. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
  • Page 149 Roadside emergencies Standard fuse amperage rating and color COLOR Cartridge Fuse Mini Standard Maxi Fuse link maxi rating fuses fuses fuses cartridge fuses Grey Grey — — — Violet Violet — — — Pink Pink — — — — — —...
  • Page 150 Roadside emergencies RELAY The fuses are coded as follows. Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description Lighting Control Module (LCM), Left-Hand Low Beam Headlamp EATC Blower Motor Lighting Control Module (LCM), Right-Hand Low Beam Headlamp 7.5A Instrument Cluster 7.5A Lighting Control Module (LCM), Instrument Panel Light...
  • Page 151 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description — Not Used Instrument Cluster, Anti-Theft, Ignition Switch, Ignition Coils Anti-Lock Brake Module, Traction Control Switch 7.5A Transmission Control Switch, Lighting Control Module (LCM), VCS Multi-Function Switch, Turn Signals Wiper Control Module (WCM), Windshield Wiper Motor Digital Transmission Range (DTR) Sensor,...
  • Page 152 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description Heated Mirrors LF Door Module, Door Locks, Decklid Release 7.5A LF Seat Module, Trunk Lid Release Switch, Door Lock Switches, LF Seat Control Switch, LF Door Module, Power Mirror Switch 7.5A Main Light Switch, Lighting Control...
  • Page 153 Roadside emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 50A** Ignition Switch 40A** Ignition Switch 50A** Cooling Fan-High Speed 30A** PCM Power Relay 40A** I/P Fuse Panel, Fuses 11, 19, 21, 23, 25, 27, and 32(Long Wheel Base Only) —...
  • Page 154 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 40A** Accessory Delay Relay (Signature/Cartier), Power Window Relay (Executive), I/P Fuse Panel, Fuse 29, 30A** Air Suspension 30A* Rear Heated Seats (Long Wheel Base Only) 20A* Rear Power Point (Long Wheel Base Only) 20A* Rear Power Point (Longe Wheel Base) 30A*...
  • Page 155 Roadside emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Temporary spare tire information Your vehicle may have a temporary or full-size spare tire.
  • Page 156 Roadside emergencies 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine OFF and block the diagonally opposite wheel. 3. Remove the spare tire and the jack. The jack could be located: •...
  • Page 157 Roadside emergencies 4. Remove the lug wrench (A) from the jack. Rotate the lug wrench socket out from the handle. 5. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle.
  • Page 158 Roadside emergencies • Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. To lessen risk of personnal injury, do not put any part of your body under the vehicle while changing a tire.
  • Page 159 Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
  • Page 160 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
  • Page 161 Roadside emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
  • Page 162 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
  • Page 163 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
  • Page 164 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.

  • Page 165: Maintenance And Care

    Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
  • Page 166 Maintenance and care Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on 1.
  • Page 167 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. Brake fluid reservoir 2. Engine oil dipstick 3. Engine oil filler cap 4. Air filter assembly 5. Power steering fluid reservoir 6. Engine coolant reservoir 7. Battery 8.
  • Page 168 Maintenance and care ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait up to 10 minutes for the oil to drain into the oil pan.
  • Page 169 Maintenance and care • If the oil level is below this mark, engine oil must be added to raise the level within the DO NOT OVERFILL normal operating range. • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter.
  • Page 170 Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
  • Page 171 MAX. Do not fill above this line. 4. Use only brake fluids certified to meet Ford specification ESA-M6C25–A. Refer to Lubricant specifications in the Capacities and specifications chapter. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used.
  • Page 172 In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
  • Page 173 Maintenance and care • Freeze protection down to -36° C (-34° F). • Boiling protection up to 129° C (265° F). • Protection against rust and other forms of corrosion. • Enables calibrated gauges to work properly. When the engine is cold, check the level of the engine coolant in the reservoir.
  • Page 174 The cooling system in your vehicle is filled with either green-colored Motorcraft Premium Engine Coolant meeting Ford specification ESE-M97B44–A or yellow-colored Motorcraft Premium Gold Engine Coolant meeting Ford Specification WSS-M97B51–A1. To determine your vehicle’s coolant type (color), check your coolant reservoir. • Add Motorcraft Premium Engine Coolant (green-colored), VC-4–A (U.S.) or CXC-10 (Canada) or Motorcraft Premium...
  • Page 175 Maintenance and care • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled Engine Coolant section). For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool.
  • Page 176 Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored). However, not all coolant recycling processes produce coolant that meets Ford specification ESE-M97B44–A.
  • Page 177 Maintenance and care If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration above 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage.
  • Page 178 Maintenance and care When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The symbol will begin to flash. •...
  • Page 179 Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
  • Page 180 Maintenance and care Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking.
  • Page 181 Maintenance and care You can check the fluid without driving if the ambient temperature is above 10°C (50°F). However, if fluid is added at this time, an overfill condition could result when the vehicle reaches normal operating temperature. The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]).
  • Page 182 Maintenance and care If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.
  • Page 183 Maintenance and care Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
  • Page 184 Maintenance and care • The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
  • Page 185 Maintenance and care 6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated.
  • Page 186 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
  • Page 187 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
  • Page 188 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
  • Page 189 Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over.
  • Page 190 Maintenance and care Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory or equivalent. Using SAE class S or other conventional link type chains may cause damage to the vehicle’s wheel house and/or body.
  • Page 191 Maintenance and care Gasoline may contain benzene, which is a cancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling.
  • Page 192 Maintenance and care When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
  • Page 193 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
  • Page 194 Auto Makers’ Choice logo. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
  • Page 195 Maintenance and care Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the scheduled maintenance guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used.
  • Page 196 Maintenance and care • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up.
  • Page 197 Maintenance and care • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. •...
  • Page 198 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine...
  • Page 199 Maintenance and care Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the “Service Engine Soon” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly.
  • Page 200 Maintenance and care Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. BULBS Replacing exterior bulbs Check the operation of the following lamps frequently:...
  • Page 201 Maintenance and care 3. Twist the plastic knobs and remove the protective cover from the back of the headlamps. Lift the cover and pull towards the windshield. 4. Remove headlamp by taking the retainer pins out. Pull headlamp forward to access bulb connector. 5.
  • Page 202 Maintenance and care 6. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb. 7.
  • Page 203 Maintenance and care Replacing front parking lamp/turn signal lamp bulbs 1. Make sure the headlamp control is in the OFF position. 2. Open the hood. 3. Twist the plastic knobs and remove the protective cover from the back of the headlamps. Lift the cover and pull towards the windshield. 4.
  • Page 204 Maintenance and care Replacing high-mount brakelamp bulbs 1. Remove the lamp cover by prying 2. Rotate the bulb socket counterclockwise and remove from lamp assembly. 3. Carefully pull the bulb straight out of socket and push in the new bulb. 4.
  • Page 205 Maintenance and care Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility.
  • Page 206 Maintenance and care You will need one 4 mm wrench or socket to make the adjustments. If the vehicle has been in an accident, the vehicle’s front structure should be properly aligned before aiming the headlamps. Horizontal aim adjustment 1. Park the vehicle on a level surface.
  • Page 207 When the horizontal and vertical indicators are set to the “0” mark, the headlamp has been properly aimed. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water.
  • Page 208 Ultra Touch Prep and Finishing Kit (F7AZ-19K507–BA), Lacquer Touch-up Paint (ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on...
  • Page 209 Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.
  • Page 210 Maintenance and care Ford Dealer. Do not use abrasive cleansers on glass as they may cause scratches. The windshield or rear window is clean if beads do not form when you rinse it with water. The windshield, rear window and wiper blades should be cleaned on a regular basis, and blades or rubber elements replaced when worn.
  • Page 211 Maintenance and care Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.
  • Page 212 For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.

  • Page 213: Capacities And Specifications

    AWSF-32P Included in long wheelbase package. Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part Name Capacity Engine oil (includes Motorcraft SAE 5W-20 filter change) Super Premium Motor 4.7L (5.0 quarts)
  • Page 214 Fill to line on reservoir fluid Washer Concentrate Use only brake fluids certified to meet Ford specifications. Refer to Lubricant Specifications in this chapter. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used.
  • Page 215 Capacities and specifications LUBRICANT SPECIFICATIONS Item Ford part Ford part Ford name number specification Brake fluid Motorcraft High C6AZ-19542-AB ESA-M6C25-A Performance and DOT 3 DOT 3 Motor Vehicle Brake Fluid Door Silicone F7AZ-19G208-BA ESR-M13P4-A weatherstrips Lubricant F5AZ-19553-AA Engine coolant Motorcraft VC-4–A (US) or...
  • Page 216 Windshield Washer Concentrate Use only brake fluids certified to meet Ford specifications. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118-A for complete refill of Traction-Lok rear axles.
  • Page 217 Capacities and specifications VEHICLE DIMENSIONS Vehicle dimensions mm (in) (1) Overall length 5 469 (215.3)/5 621 (221.3) (2) Overall width 1 987 (78.2) (3) Overall height 1 472 (58.0) (4) Wheelbase 2 990 (117.7)/3 142 (123.7) (5) Track - Front 1 611 (63.4) (5) Track - Rear 1 659 (65.3)
  • Page 218 Capacities and specifications...
  • Page 219 Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.

  • Page 220: Customer Assistance

    5,000 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to...
  • Page 221 Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
  • Page 222 P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: • Your telephone number (home and business).
  • Page 223 THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford...
  • Page 224 • the name of the dealer(s) who sold or serviced the vehicle • a brief description of your unresolved concern • a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) •...
  • Page 225 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
  • Page 226 UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
  • Page 227 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
  • Page 228 Customer assistance Vehicle Security Styled wheel locks Vehicle security systems Comfort and convenience Cargo nets Cargo organizers Engine block heaters Travel equipment Cell phone holder Floor mounted console organizer Inside rear view mirror (Electrochromic with compass and temperature display) HomeLink Protection and appearance equipment Air bag anti-theft locks Car covers...
  • Page 229 • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. ORDERING ADDITIONAL OWNER’S LITERATURE...
  • Page 230 Customer assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer...

  • Page 231: Reporting Safety Defects

    However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.

  • Page 232: Index

    Index Accessory delay ......74 Battery ........181 acid, treating emergencies ..181 Air bag supplemental restraint charging system warning system ........110, 115 light ..........11 and child safety seats ....112 jumping a disabled battery ..158 description ......110, 115 maintenance-free ....181 disposal ........118 replacement, specifications ...212 driver air bag ....112, 116 servicing ........181 indicator light .....9, 114, 117...
  • Page 233 ....214–215 Emergencies, roadside Cruise control (see Speed jump-starting ......158 control) ........62 Emission control system ..197 Customer Assistance ....145 Ford accessories for your Engine ........215–216 vehicle ........226 check engine/service engine Ford Extended Service soon light ........8 Plan ..........219 cleaning ........209...
  • Page 234 Index coolant ........171 fuel pump shut-off switch ..146 fail-safe coolant ......176 gauge .........16 idle speed control ....181 improving fuel economy ..194 lubrication octane rating ...192, 215–216 specifications ....214–215 quality ........193 refill capacities ......212 running out of fuel ....193 service points ......166 safety information relating to starting after a collision ..146 automotive fuels .....189...
  • Page 235 Index aiming ......204–206 autolock ........83 autolamp system .......25 keypad ........85 bulb specifications ....204 programming entry code ..86 daytime running lights .....26 Keys .........60, 88, 90 flash to pass ......26 key in ignition chime ....15 high beam ......11, 26 positions of the ignition ...59 replacing bulbs .......199 turning on and off ....25–26 warning chime ......15...
  • Page 236 Index turn signal indicator ....11 Parking brake ......131 Load limits .........139 Parts (see Motorcraft parts) ..212 GAWR ........139 Passenger Occupant GVWR ........139 Classification Sensor ....98 trailer towing ......139 Pedals (see Power adjustable Locks foot pedals) .........58 autolock ........83 Power distribution box (see childproof ........75 Fuses) ........151 doors ..........74...
  • Page 237 Index extension assembly ....105 for adults ......101–103 for children ......118 Tires ......154, 185–187 lap belt ........104 changing ........154 Occupant Classification checking the pressure ....187 Sensor ........98 replacing ........188 warning light and rotating ........187 chime .....9, 14, 105–106 snow tires and chains ....188 tire grades .......186 Safety seats for children ..119 treadwear ........186...
  • Page 238 Index Windshield washer fluid and wipers Warning chimes .....14–15 checking and adding fluid ..171 checking and cleaning ....184 Warning lights (see Lights) ..8 operation ........61 Washer fluid ......171 replacing wiper blades ...184 Water, Driving through .....144 Wrecker towing ......163 Windows power .........73...

  • Page 241: Filling Station Information

    Use either green-colored Motorcraft Premium Engine Coolant or yellow-colored Motorcraft Premium Gold Engine Coolant. DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.

This manual is also suitable for:

Mercury 2001

Table of Contents