Toshiba Tosvert VF-S15 Instruction Manual page 327

 Table of input terminal functions 3
Function
Code
No.
100 RS Run/Stop command
101 RSN Inversion of run/Stop command
104 FCHG Frequency setting mode forced switching
105 FCHGN Inversion of frequency setting mode forced
switching
106 FMTB Frequency setting mode terminal block
107 FMTBN Inversion of frequency setting mode terminal
block
108 CMTB Command mode terminal block
109 CMTBN Inversion of command mode terminal block
110 PWE Parameter editing permission
111 PWEN Inversion of parameter editing permission
120 FSTP1 Fast stop command 1
121 FSTP1N Inversion of fast stop command 1
122 FSTP2 Fast stop command 2
123 FSTP2N Inversion of fast stop command 2
134 TVS Traverse permission signal
135 TVSN Inversion of traverse permission signal
136 RSC Low voltage operation signal
137 RSCN Inversion of low voltage operation signal
140 SLOWF Forward deceleration
141 SLOWFN Inversion of forward deceleration
142 STOPF Forward stop
143 STOPFN Inversion of forward stop
144 SLOWR Reverse deceleration
145 SLOWRN Inversion of reverse deceleration
146 STOPR Reverse stop
147 STOPRN Inversion of reverse stop
148 to 151 Factory specific coefficient
152 MOT2 No.2 motor switching
（AD2＋VF2＋OCS2）
153 MOT2N Inversion of No.2 motor switching
（AD2＋VF2＋OCS2）
158 RES2 Reset command 2 *2
159 RES2N Inversion of reset command 2 *2
200 PWP Parameter editing prohibition
201 PWPN Inversion of parameter editing prohibition
PRWP Parameter reading prohibition
202
203 PRWPN Inversion of parameter reading prohibition
*1: Factory specific coefficient parameters are manufacturer setting parameters. Do not change the value of these parameters.
*2: These functions are cannot be assigned to Always active function selection 1 to 3 (f104, f108, f110).
Note 1: Function No. that are not described in the table above are assigned "No function".
Function
ON: Run command
OFF: Stop command
Inversion of RS
ON: f207 (f200=0)
OFF: fmod
Inversion of FCHG
ON: Terminal block (VIA) enabled
OFF: Setting of 
Inversion of FMTB
ON: Terminal block enabled
OFF: Setting of 
Inversion of CMTB
ON: Parameter editing permitted
OFF: Setting of 
Inversion of PWE
ON: Dynamic quick deceleration command
OFF: Forced deceleration canceled
(Note that operation is resumed when forced deceleration is canceled)
Inversion of FSTP1
ON: Automatic deceleration
OFF: Forced deceleration canceled
(Note that operation is resumed when forced deceleration is canceled)
Inversion of FSTP2
ON: Permission signal of traverse operation
OFF: Normal operation
Inversion of TVS
ON: Low voltage operation
OFF: Low voltage operation canceled
Inversion of RSC
ON: Forward operation with f383 frequency
OFF: Normal operation
Inversion of SLOWF
ON: Forward stop, OFF: Normal operation
Inversion of STOPF
ON: Reverse operation with f383 frequency
OFF: Normal operation
Inversion of SLOWR
ON: Reverse stop, OFF: Normal operation
Inversion of STOPR
ON: No.2 motor
(=0, , , ,  (thr when
f632=2 or 3), , , , )
OFF: No.1 motor (Set value of , , , , ,
, , , )
Inversion of MOT2
ON: Trip reset
Inversion of RES2
ON: Parameter editing prohibited
OFF: Setting of 
Inversion of PWP
ON: Parameter reading / editing prohibited
OFF: Setting of 
Inversion of PRWP
K-33
E6581926
Action
-
Reference
7.2.1
6.2.1
6.34.1
6.1.4
6.40
6.17
6.22.2
11
*1
6.8.1
13.2
6.34.1