Omron E5CN-H Communications Manual page 53

SECTION 3 Communications Data for CompoWay/F and SYSWAY
Variable
Address Parameter name
type
C1 (81) 0022 MV at Stop
C1 (81) 0023 MV at PV Error
C1 (81) 0024 Manual MV
C1 (81) 0025 SP Ramp Set Value (See note 1.)
C1 (81) 0026 MV Upper Limit (See note 2.)
C1 (81) 0027 MV Lower Limit (See note 2.)
C1 (81) 0028 Move to Protect Level
C1 (81) 0029 Password to Move to Protect Level
C1 (81) 002A Parameter Mask Enable
C1 (81) 002B PF Key Protect
C1 (81) 002C MV Change Rate Limit
C1 (81) 002D Position Proportional Dead Band
C1 (81) 002E Open/Close Hysteresis
C1 (81) 002F Heater Overcurrent Detection 1
C1 (81) 0030 Heater Overcurrent Detection 2
C1 (81) 0031 Extraction of Square Root Low-cut
Point
Note 1: The parameter for the currently selected bank will be accessed.
Note 2: The parameter for the currently selected PID set will be accessed. For setup area 1, however, the currently selected PID
set is fixed at PID1.
3-4
Setting (monitor) value
Standard: H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A ( − 105.0 to 105.0)
Position proportional (Floating or direct setting of position proportional
MV OFF): H'FFFFFFFF to H'00000001 ( − 1 to 1)
Position proportional (Closed and direct setting of position proportional
MV ON): H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Standard: H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A ( − 105.0 to 105.0)
Position proportional (Floating or direct setting of position proportional
MV OFF): H'FFFFFFFF to H'00000001 ( − 1 to 1)
Position proportional (Closed and direct setting of position proportional
MV ON): H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Standard: H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A ( − 105.0 to 105.0)
Position proportional (Floating or direct setting of position proportional
MV OFF): H'FFFFFFFF to H'00000001 ( − 1 to 1)
Position proportional (Closed and direct setting of position proportional
MV ON): H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
H'00000000(0): OFF
H'00000001 to H'00007E90 (1 to 32400)
Standard: MV lower limit + 0.1 to H'0000041A
(MV lower limit + 0.1 to 105.0)
Heating/cooling: H'00000000 to H'0000041A (0.0 to 105.0)
Position proportional (closed): MV lower limit +0.1 to H'0000041A
(MV lower limit +0.1 to 105.0)
Standard: H'FFFFFFCE to MV upper limit − 0.1
( − 5.0 to MV upper limit − 0.1)
Heating/cooling: H'FFFFFBE6 to H'00000000 ( − 105.0 to 0.0)
Position proportional (closed): H'FFFFFFCE to MV upper limit − 0.1
( − 5.0 to MV upper limit − 0.1)
H'FFFFF831 to H'0000270F ( − 1999 to 9999)
H'FFFFF831 to H'0000270F ( − 1999 to 9999)
(Can only be set. The monitor value is always H'00000000.)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 to H'000003E8 (0.0 to 100.0)
H'00000001 to H'00000064 (0.1 to 10.0)
H'00000001 to H'000000C8 (0.1 to 20.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'000003E8 (0.0 to 100.0)
Level
Adjustment
Manual
Control
Adjustment
Protect
Adjustment