Omron E5CN-H Communications Manual page 111

SECTION 6 Communications Data for Modbus
Address
Parameter name
Four-byte Two-byte
mode mode
1022 3011 PV Status Display Function
1024 3012 SV Status Display Function
1100 3100 Communications Protocol Set-
ting (See note 1.)
1102 3101 Communications Unit No.
(See note 1.)
1104 3102 Communications Baud Rate
(See note 1.)
1106 3103 Communications Data Length
(See note 1.)
1108 3104 Communications Stop Bits
(See note 1.)
110A 3105 Communications Parity
(See note 1.)
110C 3106 Send Data Wait Time
(See note 1.)
1200 3200 PF Setting
1204 3202 Monitor/Setting Item 1
Note 1: After communications parameters have been changed, reset the Controller to enable them.
6-10
Setting (monitor) value
H'00000000 (0):OFF
H'00000001 (1): Manual
H'00000002 (2): Stop
H'00000003 (3): Alarm 1
H'00000004 (4): Alarm 2
H'00000005 (5): Alarm 3
H'00000006 (6): Alarm 1 to 3 OR status
H'00000007 (7): Heater alarm
H'00000000 to H'00000007 (0 to 7)
* Same as for PV Status Display Function.
H'00000000 (0): CompoWay/F (SYSWAY)
H'00000001 (1): Modbus
H'00000000 to H'00000063 (0 to 99)
H'00000000 (0): 1.2
H'00000001 (1): 2.4
H'00000002 (2): 4.8
H'00000003 (3): 9.6
H'00000004 (4): 19.2
H'00000005 (5): 38.4
H'00000006 (6): 57.6
H'00000007 (7): 7
H'00000008 (8): 8
H'00000001 (1): 1
H'00000002 (2): 2
H'00000000 (0): None
H'00000001 (1): Even
H'00000002 (2): Odd
H'00000000 to H'00000063 (0 to 99)
H'00000000 (0): OFF
H'00000001 (1): RUN
H'00000002 (2): STOP
H'00000003 (3): RUN/STOP
H'00000004 (4): 100% AT execute/cancel
H'00000005 (5): 40% AT execute/cancel
H'00000006 (6): Alarm latch cancel
H'00000007 (7): Auto/manual
H'00000008 (8): Monitor/setting item
H'00000009 (9): Bank change
H'00000000 (0): Disable
H'00000001 (1): PV/SP/Bank No.
H'00000002 (2): PV/SP/MV
H'00000003 (3): PV/SP/soak time remain
H'00000004 (4): Proportional band (P)
H'00000005 (5): Integral time (I)
H'00000006 (6): Derivative time (D)
H'00000007 (7): Alarm value 1
H'00000008 (8): Alarm value upper limit 1
H'00000009 (9): Alarm value lower limit 1
H'0000000A (10): Alarm value 2
H'0000000B (11): Alarm value upper limit 2
H'0000000C (12): Alarm value lower limit 2
H'0000000D (13): Alarm value 3
H'0000000E (14): Alarm value upper limit 3
H'0000000F (15): Alarm value lower limit 3
H'000000010 (16): Bank No.
Level
Advanced
function
setting
Communi-
cations
setting
Advanced
function
setting