Omron E5CN-H Communications Manual page 107
Digital controllers
Hide thumbs
Also See for E5CN-H:
- Datasheet (23 pages) ,
- Instruction manual (2 pages) ,
- User manual (374 pages)
Table of Contents
Advertisement
SECTION 6 Communications Data for Modbus
Address
Parameter name
Four-byte
Two-byte
mode
mode
0D22
2D11
Standard or Heating/Cooling
0D24
2D12
Direct/Reverse Operation
0D26
2D13
Closed/Floating
0D28
2D14
PID ON/OFF
0D2A
2D15
ST
0D2C
2D16
Program Pattern
0D2E
2D17
Valid Program Bank
0E00
2E00
Transfer Output Type
0E0C
2E06
Control Output 1 Assignment
0E0E
2E07
Control Output 2 Assignment
Note 1:
P.END (program end output) can be set even when the program pattern is set to OFF, but the function will be disabled.
Note 2:
The output turns ON when the status of either the Control Output 1 ON/OFF Count Alarm or the Control Output 2 ON/OFF
Count Alarm turns ON.
6-6
Setting (monitor) value
H'00000000 (0): Standard
H'00000001 (1): Heating/cooling
H'00000000 (0): Reverse operation
H'00000001 (1): Direct operation
H'00000000 (0): Floating
H'00000001 (1): Closed
H'00000000 (0): ON/OFF
H'00000001 (1): 2 PID control
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): STOP
H'00000002 (2): CONT
H'00000003 (3): LOOP
H'00000000 to H'00000007 (0 to 7)
H'00000000 (0): OFF
H'00000001 (1): Set point
H'00000002 (2): Set point during SP ramp
H'00000003 (3): PV
H'00000004 (4): MV monitor (heating)
H'00000005 (5): MV monitor (cooling)
H'00000006 (6): Valve Opening
When control output 1 is a linear output:
H'00000000 (0): Not assigned.
H'00000001 (1): Control output (heating)
H'00000002 (2): Control output (cooling)
When control output 1 is an ON/OFF output:
H'00000000 (0): Not assigned.
H'00000001 (1): Control output (heating)
H'00000002 (2): Control output (cooling)
H'00000003 (3): Alarm 1
H'00000004 (4): Alarm 2
H'00000005 (5): Alarm 3
H'00000006 (6): Program end output (See note 1.)
H'00000007 (7): Control output ON/OFF count alarm (See note 2.)
H'00000008 (8): Work bit 1
H'00000009 (9): Work bit 2
H'0000000A (10): Work bit 3
H'0000000B (11): Work bit 4
H'0000000C (12): Work bit 5
H'0000000D (13): Work bit 6
H'0000000E (14): Work bit 7
H'0000000F (15): Work bit 8
When control output 2 is a linear output: H'00000000 to H'00000002 (0 to 2)
(Same as for Control Output 1 Assignment.)
When control output 2 is an ON/OFF output: H'00000000 to H'0000000F (0 to
15) (Same as for Control Output 1 Assignment.)
Level
Initial
setting
Advanced
function
setting
Advertisement
Table of Contents
