Omron E5CN-H Communications Manual page 104

Address
Parameter name
Four-byte Two-byte
mode mode
0500 2500 Operation/Adjustment Protect
0502 2501 Initial Setting/Communications
Protect
0504 2502 Setting Change Protect
0506 2503 PF Key Protect
0508 2504 Move to Protect Level
050A 2505 Password to Move to Protect
Level
050C 2506 Parameter Mask Enable
0600 2600 Manual MV
0602 2601 Set Point (See note 1.)
0604 2602 Remote SP Monitor
0608 2604 Heater Current 1 Value Monitor
060A 2605 MV Monitor (Heating)
060C 2606 MV Monitor (Cooling)
060E 2607 Valve Opening Monitor
0700 2700 Cooling Coefficient (See note 2.) H'00000001 to H'0000270F (0.01 to 99.99)
0708 2704 Dead Band
070A 2705 Manual Reset Value
070C 2706 Hysteresis (Heating)
070E 2707 Hysteresis (Cooling)
0710 2708 Control Period (Heating)
0712 2709 Control Period (Cooling)
0714 270A Position Proportional Dead
Band
0716 270B Open/Close Hysteresis
0718 270C SP Ramp Time Unit
071A 270D SP Ramp Set Value
(See note 1.)
071E 270F MV at Stop
Note 1: The parameter for the currently selected bank will be accessed.
Note 2: The parameter for the currently selected PID set will be accessed. For setup area 1, however, the currently selected PID
set is fixed at PID1.
6.1 Variable Area (Setting Range) List
Setting (monitor) value
H'00000000 (0): No restrictions in operation and adjustment levels
H'00000001 (1): Move to adjustment level is prohibited.
H'00000002 (2): Display and change of only "PV" and "PV/SP" parameters is
allowed.
H'00000003 (3): Display of only "PV" and "PV/SP" parameters is allowed.
H'00000000 (0): Move to initial setting/communications setting level is allowed.
(Move to advanced function setting level is displayed.)
H'00000001 (1): Move to initial setting/communications setting level is allowed.
(Move to advanced function setting level is not displayed.)
H'00000002 (2): Move to initial setting/communications setting level is prohib-
ited.
H'00000000 (0): OFF (Changing of setup on controller display is allowed.)
H'00000001 (1): ON (Changing of setup on controller display is prohibited.)
H'00000000 (0): OFF
H'00000001 (1): ON
H'FFFFF831 to H'0000270F ( − 1999 to 9999)
H'FFFFF831 to H'0000270F ( − 1999 to 9999)
(Can only be set. The monitor value is always H'00000000.)
H'00000000 (0): OFF
H'00000001 (1): ON
Standard: H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A ( − 105.0 to 105.0)
Position proportional (Closed and direct setting of position proportional MV
ON): H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
SP lower limit to SP upper limit
Remote SP lower limit to Remote SP upper limit
H'00000000 to H'00000226 (0.0 to 55.0)
Standard: H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Heating and cooling: H'00000000 to H'0000041A (0.0 to 105.0)
H'00000000 to H'0000041A (0.0 to 105.0)
H'FFFFFF9C to H'0000044C ( − 10.0 to 110.0)
Temperature: H'FFFFB1E1 to H'00007E90 ( − 1999.9 to 3240.0)
Analog: H'FFFFF831 to H'0000270F ( − 199.9 to 999.9)
H'00000000 to H'000003E8 (0.0 to 100.0)
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.1 to 999.9)
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.1 to 999.9)
H'00000000 (0): 0.5
H'00000001 to H'00000063 (1 to 99)
H'00000000 (0): 0.5
H'00000001 to H'00000063 (1 to 99)
H'00000001 to H'00000064 (0.1 to 10.0)
H'00000001 to H'000000C8 (0.1 to 20.0)
H'00000000 (0): EU/second
H'00000001 (1): EU/minute
H'00000002 (2): EU/hour
H'00000000 (0): OFF
H'00000001 to H'00007E90 (1 to 32400)
Standard: H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A ( − 105.0 to 105.0)
Position proportional (Floating or direct setting of position proportional MV
OFF): H'FFFFFFFF to H'00000001 ( − 1 to 1)
Position proportional (Closed and direct setting of position proportional MV
ON): H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Level
Protect
Manual
Control
Operation
Adjustment
Initial
setting
Adjustment
Advanced
function
setting
Adjustment
6-3