Omron E5CN-H Communications Manual page 105

SECTION 6 Communications Data for Modbus
Address
Four- Two- Parameter name
byte byte
mode mode
0722 2711 MV at PV Error
0726 2713 MV Change Rate Limit
072C 2716 Lower Limit Temperature Input Shift Value
0730 2718 Upper Limit Temperature Input Shift Value
0734 271A Heater Current 1 Value Monitor
0736 271B Heater Burnout Detection 1
0738 271C Leakage Current 1 Monitor
073A 271D HS Alarm 1
0746 2723 Temperature Input Shift
0748 2724 Heater Current 2 Value Monitor
074A 2725 Heater Burnout Detection 2
074C 2726 Leakage Current 2 Monitor
074E 2727 HS Alarm 2
0750 2728 Soak Time Remain
0752 2729 Soak Time (See note 1.)
0754 272A Wait Band (See note 1.)
0756 272B Heater Overcurrent Detection 1
0758 272C Heater Overcurrent Detection 2
0800 2800 Input Digital Filter
0810 2808 Extraction of Square Root Low-cut Point
0904 2902 Alarm Value 1 (See note 1.)
0906 2903 Alarm Value Upper Limit 1 (See note 1.)
0908 2904 Alarm Value Lower Limit 1 (See note 1.)
090A 2905 Alarm Value 2 (See note 1.)
090C 2906 Alarm Value Upper Limit 2 (See note 1.)
090E 2907 Alarm Value Lower Limit 2 (See note 1.)
0910 2908 Alarm Value 3 (See notes 1 and 2.)
Alarm Value Upper Limit 3 (See notes 1 and 2.) H'FFFFB1E1 to H'00007E90 ( − 19999 to 32400)
0912 2909
Alarm Value Lower Limit 3 (See notes 1 and 2.) H'FFFFB1E1 to H'00007E90 ( − 19999 to 32400)
0914 290A
0A00 2A00 Proportional Band (See note 3.)
0A02 2A01 Integral Time (See note 3.)
0A04 2A02 Derivative Time (See note 3.)
0A0A 2A05 MV Upper Limit (See note 3.)
Note: The alarm function can also be used in Controllers without alarm output terminals. In this case, confirm alarm occurrences via the
status data.
Note 1: The parameter for the currently selected bank will be accessed.
Note 2: Not displayed on the Controller display when Alarm 3 is not assigned to an output.
Note 3: The parameter for the currently selected PID set will be accessed. For setup area 1, however, the currently selected PID set is fixed at
PID1.
6-4
Setting (monitor) value
Standard: H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A ( − 105.0 to 105.0)
Position proportional (Floating or direct setting of position propor-
tional MV OFF): H'FFFFFFFF to H'00000001 ( − 1 to 1)
Position proportional (Closed and direct setting of position propor-
tional MV ON): H'FFFFFFCE to H'0000041A ( − 5.0 to 105.0)
H'00000000 to H'000003E8 (0.0 to 100.0)
H'FFFFB1E1 to H'00007E90 ( − 199.99 to 324.00)
H'FFFFB1E1 to H'00007E90 ( − 199.99 to 324.00)
H'00000000 to H'00000226 (0.0 to 55.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'00000226 (0.0 to 55.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'FFFFB1E1 to H'00007E90 ( − 199.99 to 324.00)
H'00000000 to H'00000226 (0.0 to 55.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'00000226 (0.0 to 55.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'0000270F (0 to 9999)
H'00000000 to H'0000270F (0 to 9999)
H'00000000 (0): OFF
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.01 to 99.99)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'0000270F (0.0 to 999.9)
H'00000000 to H'000003E8 (0.0 to 100.0)
H'FFFFB1E1 to H'00007E90 ( − 19999 to 32400)
H'FFFFB1E1 to H'00007E90 ( − 19999 to 32400)
H'FFFFB1E1 to H'00007E90 ( − 19999 to 32400)
H'FFFFB1E1 to H'00007E90 ( − 19999 to 32400)
H'FFFFB1E1 to H'00007E90 ( − 19999 to 32400)
H'FFFFB1E1 to H'00007E90 ( − 19999 to 32400)
H'FFFFB1E1 to H'00007E90 ( − 19999 to 32400)
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.1 to 999.9)
Standard, heating/cooling, position proportional (closed):
H'00000000 to H'00007E90 (0.0 to 3240.0)
Position proportional (floating): H'00000001 to H'00007E90
(0.1 to 3240.0)
H'00000000 to H'00007E90 (0.0 to 3240.0)
Standard: MV lower limit +0.1 to H'0000041A
(MV lower limit +0.1 to 105.0)
Heating/cooling: H'00000000 to H'0000041A (0.0 to 105.0)
Position proportional (closed): MV lower limit +0.1 to H'0000041A)
MV lower limit +0.1 to 105.0)
Level
Adjustment
Operation
Adjustment
Operation
Adjustment
Operation
Adjustment
Operation
Adjustment
Operation
Adjustment
Advanced
function
setting
Adjustment
Operation
Adjustment