Husqvarna TE 250-310 2012 I.E. Workshop Manual page 273

TE 250 - 310 2012 I.E. / TE 250 - 310 2012 I.E. USA
TC 250 2012 - TC 250 2012 I.E. USA
TXC 250 - 310 2012 I.E. USA
ELECTRICAL SYSTEM
• Position of the connectors front side ...................................................... M.41
• Control unit connection (TC) .................................................................. M.42
• Ignition coil / stick-coil connection (TC).................................................. M.42
• Air temperature sensor connection (TC) ................................................ M.42
• Connection of the injector sensor (7), throttle position sensor (9),
and MAP sensor (8) ............................................................................... M.42
• Fuel pump connector position (TC)........................................................ M.43
• Securing the wiring (TC) ........................................................................ M.43
• Securing the engine stop button cable (TC) ........................................... M.43
• Voltage regulator connection (TC) ......................................................... M.44
• Connection of alternator (TC) ................................................................ M.44
• Condenser connection (TC) ................................................................... M.44
Wiring (TE-TXC) ........................................................................................ M.45
Cable routing and electrical parts installation instructions "TE-TXC" ....... M.46
• Coil position TE-TXC .............................................................................. M.46
• Relay (1) and fuses (2) position (TE-TXC) ............................................. M.46
• Turning indicators flasher (3) (TE) and solenoid starter .......................... M.3
position (TE-TXC) ................................................................................ M.46
• Position of control unit (5) and voltage regulator (6) (TE - TXC). .......... M.47
• Securing the starter motor/solenoid starter cable (TE-TXC) .................. M.47
• Securing the engine ground to chassis and engine ground to
battery cables (8) (TE-TXC) ................................................................... M.47
• Battery negative cable routing (TE-TXC) ............................................... M.47
• Securing the voltage regulator ground cable (9) (TE-TXC) .................... M.48
• Securing the engine ground / chassis ground cables (10). ................... M.48
• Wiring connection to voltage regulator (TE-TXC) .................................. M.48
• Connection of relays and fuses (TE-TXC) ............................................. M.49
• Electric fan connection (TE-TXC) .......................................................... M.49
• Injector connection (TE-TXC) ................................................................ M.49
• Ignition coil connection (TE-TXC) .......................................................... M.49
• Fuel pump connector position (TE-TXC) ............................................... M.50
• MAQS connector (TE-TXC) ................................................................... M.50
• Engine water temperature connector (TE-TXC) .................................... M.50
• Lambda sensor position and connector (TE-TXC)................................ M.50
• Ignition and gear sensor cable connection ............................................ M.51
• Routing of rear chassis cables, tail light connection, flasher contactor. . M.51
• Clip installation on fuse holders ............................................................. M.51
• Clip installation on fuse holders ............................................................. M.52
• Rear stop connection ............................................................................. M.52
• Routing of steering head tube wiring ..................................................... M.52
• Dashboard bracket connectors (TE) ...................................................... M.52
• Headlamp, front turning indicators, STOP connection (TE) ................... M.52
• Double map connector (TE) ................................................................... M.53
• Speed sensor and ignition switch connectors (TE) ................................ M.53
• Horn connector (TE) .............................................................................. M.53
• Securing the wiring harness to rear chassis right side........................... M.54
• Securing the wiring harness to rear chassis left side ............................. M.54
• Securing the wiring harness to the chassis............................................ M.54
Important ................................................................................................... M.56
M.3
Workshop Manual Ed. 12-2011