Kärcher KM 120/150 R Bp Pack User Manual page 28

Sweeping mode
Danger
Risk of injury! If the bulk waste flap is open,
stones or gravel may be flung forwards by
the roller brush. Make sure that this does
not endanger persons, animals or objects.
Warning
Do not sweep up packing strips, wire or
similar objects as this may damage the
sweeping mechanism.
Note
The sweeping roller and the side brushes
automatically switch off when the machine
is idling.
Warning
To avoid damaging the floor, do not contin-
ue to operate the sweeping machine in the
same position.
Note
To achieve an optimum cleaning result, the
driving speed should be adjusted to take
specific situations into account.
Note
During operation, the waste container
should be emptied at regular intervals.
Note
When cleaning surfaces, only lower the
roller brush.
Note
Also lower side brush when cleaning along
edges.
Note
After switching the program switch from
sweeping mode to step 1 (driving), the dust
filter is automatically shaken off for a period
of approx. 15 seconds. The display re-
mains activated during this period.
Sweeping with roller brush (basic-oper-
ating mode)
Note
Two operating modes are possible with the
roller brush. In the basic-operating mode,
the roller brush is only subjected to a small
amount of wear and tear.
Set programme switch to step 2. Roller
brush is lowered.
Sweeping with roller brush (power-oper-
ating mode)
Note
Two operating modes are possible with the
roller brush. Power-operating mode in-
creases cleaning performance.
Set programme switch to step 2. Roller
brush is lowered.
Press power button. Control lamp glows
green.
Note
The following actions reset the power but-
ton automatically:
– Press the power button again.
28
– Set programme switch to step 1 (driv-
ing).
– Switching off the machine.
The indicator lamp goes out and the basic-
operating mode is activated.
Note
To sweep up larger items with a height of
60 mm, e.g. soft drink cans, the bulk waste
flap must be raised briefly.
Sweeping with bulk waste flap raised
Raising bulk waste flap:
Press the pedal for the bulk waste flap
forwards and keep pressed down.
To lower it, take foot off pedal.
Note
An optimum cleaning result can only be
achieved if the bulk waste flap has been
lowered completely.
Sweeping with side brushes
To sweep in edge area on right-hand side:
Set programme switch to step 3. The
right side brush and roller brush are
lowered.
To sweep in edge area on left-hand side:
Set programme switch to step 4. The
left side brush and roller brush are low-
ered.
To sweep in edge areas on right- and left-
hand side:
Set programme switch to step 5. Both
side brushes and roller brush are low-
ered.
Note
Roller brush and side brush start operating
automatically.
– You can reduce the speed of the side
brushes to sweep the fine dust.
Note
The menu item "Setting speed of side
brushes" is displayed only when the pro-
gram switch is at the steps 3, 4 or 5.
Select menu item no. 3 "Setting speed
of side brushes" by turning the Info but-
ton. The currently set value is dis-
played as a bar.
Adjustable
parameters
Speed of side minimum
brushes speed
20%
Press Info button, the bar display
blinks.
Reset the parameter by turning the Info
button between "min" and "max".
Accept modified setting by pressing the
Info button or wait till the set value is ac-
cepted automatically.
9
-
EN
Sweeping dry floors
Press wet sweeping button. Indicator
lamp goes off.
Sweeping damp or wet floors
Press wet sweeping button. Control
lamp glows green.
Note
The suction blower switches off. This pro-
tects the filter from moisture.
Emptying waste container
Note
Wait until the automatic filter shaking proc-
ess is finished and the dust has settled be-
fore you open or empty the waste
container.
Danger
Risk of injury! When emptying the waste
container, care should be taken to ensure
that no persons or animals are within its
swivelling range.
Danger
Danger of crushing. Never reach into the
rod assembly for the drainage mechanism.
Stay away from the area under the raised
container.
Danger
Danger of tipping. Place the machine on an
even surface during emptying.
Stop the machine.
Set programme switch to step 1 (driv-
ing).
Note
The container can only be tilted and emp-
tied once a set minimum level has been
reached.
Note
A two-handed operation is required to carry
out the following steps.
1
maximum
speed
100%
Figure 11
Raise waste container. Press button 1
(operator console) and 2 simultaneous-
ly.
2
3
4 5