......................2-4 system location ......................2-5 system date .......................2-6 system time .......................2-7 system time-and-date synchro ..................2-8 system timezone .......................2-9 system daylight savings time ..................2-12 update ........................2-14 update lanpower .....................2-16 reload ni ........................2-17 reload all .........................2-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 4
Network Time Protocol Commands ............... 5-1 ntp server ........................5-2 ntp server synchronized ....................5-4 ntp server unsynchronized ..................5-5 ntp client ........................5-6 ntp broadcast ......................5-7 ntp broadcast-delay ....................5-8 ntp key ........................5-9 ntp key load ......................5-11 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 6
....................10-5 snmp community map ....................10-7 snmp community map mode ..................10-9 show snmp community map .................10-10 snmp security ......................10-11 show snmp security ....................10-13 show snmp statistics .....................10-15 show snmp mib family ..................10-17 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 9
..................16-171 bridge mode 1x1 pvst+ ..................16-173 bridge port pvst+ ....................16-174 Chapter 17 Loopback Detection Commands ................17-1 loopback-detection ....................17-2 loopback-detection port ..................17-3 loopback-detection transmission-timer ..............17-5 loopback-detection autorecovery-timer ..............17-6 show loopback-detection ..................17-7 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 10
..................20-26 interfaces hybrid crossover ...................20-28 interfaces hybrid duplex ..................20-30 interfaces hybrid speed ..................20-32 interfaces hybrid pause ..................20-34 show interfaces .....................20-37 show interfaces capability ..................20-41 show interfaces flow control ................20-43 show interfaces pause ...................20-45 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 11
........................22-4 vlan mobile-tag .......................22-6 vlan port default .....................22-8 vlan source-learning .....................22-10 show vlan ......................22-12 show vlan port ......................22-15 show vlan router mac status .................22-18 show vlan gvrp .....................22-20 show vlan ipmvlan ....................22-23 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 12
................24-48 Chapter 25 Ethernet OAM Commands ..................25-1 ethoam domain .......................25-3 ethoam domain mhf ....................25-5 ethoam association ....................25-7 ethoam association mhf ..................25-9 ethoam association ccm-interval ................25-11 ethoam association endpoint-list ................25-13 ethoam default-domain ..................25-15 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 14
..............29-55 arp filter ........................29-56 clear arp filter .......................29-58 icmp type ......................29-59 icmp unreachable ....................29-62 icmp echo ......................29-64 icmp timestamp ....................29-66 icmp addr-mask ....................29-68 icmp messages ......................29-70 ip dos scan close-port-penalty ................29-71 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 15
..................30-26 show ipv6 interface ....................30-29 show ipv6 pmtu table ...................30-33 clear ipv6 pmtu table ....................30-35 show ipv6 neighbors .....................30-36 clear ipv6 neighbors .....................30-38 show ipv6 prefixes ....................30-39 show ipv6 routes ....................30-41 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 16
.....................32-5 ip helper standard ....................32-7 ip helper per-vlan only ...................32-8 ip helper forward delay ..................32-10 ip helper maximum hops ..................32-12 ip helper agent-information ..................32-14 ip helper agent-information policy ...............32-16 ip helper pxe-support ....................32-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 17
....................33-19 ip rip invalid-timer ....................33-20 ip rip garbage-timer ....................33-21 ip rip holddown-timer ...................33-22 show ip rip ......................33-23 show ip rip routes ....................33-25 show ip rip interface .....................33-28 show ip rip peer ....................33-30 OmniSwitch 6250 CLI Reference Guide November 2009 xvii...
Page 19
..............39-56 policy condition source tcp port ................39-58 policy condition destination tcp port ..............39-60 policy condition source udp port ................39-62 policy condition destination udp port ..............39-64 policy condition ethertype ..................39-66 policy condition established .................39-68 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 20
802.1p ................39-162 show policy classify source ip ................39-164 show policy classify destination ip ..............39-166 show policy classify multicast ip ...............39-168 show policy classify tos ..................39-170 show policy classify dscp ...................39-172 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 22
..................43-18 aaa accounting 802.1x ..................43-20 aaa accounting session ..................43-22 aaa accounting command ..................43-24 user ........................43-26 password .......................43-30 user password-size min ..................43-32 user password-expiration ..................43-33 user password-policy cannot-contain-username ..........43-35 user password-policy min-uppercase ..............43-36 xxii OmniSwitch 6250 CLI Reference Guide November 2009...
Page 23
802.1x captive-portal address ................44-24 802.1x captive-portal proxy-server-url ..............44-25 show 802.1x ......................44-26 show 802.1x users ....................44-29 show 802.1x statistics ...................44-31 show 802.1x device classification policies ............44-33 show 802.1x non-supplicant .................44-35 show 802.1x captive-portal configuration ............44-37 OmniSwitch 6250 CLI Reference Guide November 2009 xxiii...
Page 24
Software License and Copyright Statements ........... A-15 Alcatel-Lucent License Agreement ................A-15 ALCATEL-LUCENT SOFTWARE LICENSE AGREEMENT ......A-15 Third Party Licenses and Notices ................A-18 A. Booting and Debugging Non-Proprietary Software ........A-18 B. The OpenLDAP Public License: Version 2.8, 17 August 2003 ...... A-18 C.
About This Guide This OmniSwitch 6250 CLI Reference Guide is a comprehensive resource to all Command Line Interface (CLI) commands available on the OmniSwitch 6250 Series. Supported Platforms This information in this guide applies to the following products: • OmniSwitch 6250-Enterprise Models •...
Overview information, procedures, and live network examples on switch software features may be found in the OmniSwitch 6250 Switch Management Guide and the OmniSwitch 6250 Network Configuration Guide. Once you are familiar with the procedures and base CLI commands in these configuration guides you can obtain more detailed information on the individual commands in this guide.
Indicates that the user must choose between one or more parameters. Example: port mirroring {enable | disable} Here, you must choose one of the following: port mirroring enable or port mirroring disable OmniSwitch 6250 CLI Reference Guide November 2009 page xxvii...
Page 28
“ ” (Quotation Marks) Used to enclose text strings that contain spaces. The quotation marks are required input on the command line. Example: vlan 2 “new test vlan” page xxviii OmniSwitch 6250 CLI Reference Guide November 2009...
CLI-to-MIB variable mapping information for all CLI commands supported by the switch. This guide can be consulted anytime during the configuration process to find detailed and specific information on each CLI command. OmniSwitch 6250 CLI Reference Guide November 2009 page xxix...
Related Documentation About This Guide Related Documentation The following are the titles and descriptions of all the related OmniSwitch 6250 user manuals: • OmniSwitch 6250 Series Getting Started Guide Describes the hardware and software procedures for getting an OmniSwitch 6250 Series switch up and running.
Service and Support web page, you’ll be able to view and update any case (open or closed) that you have reported to Alcatel-Lucent’s technical support, open a new case or access helpful release notes, technical bulletins, and manuals. For more information on Alcatel-Lucent’s Service Programs, see our web page at service.esd.alcatel-lucent.com, call us at 1-800-995-2696, or email us at esd.support@alcatel-lucent.com.
Page 32
Technical Support About This Guide page xxxii OmniSwitch 6250 CLI Reference Guide November 2009...
A summary of available commands is listed here: reload reload working copy running-config working write memory copy working certified copy working certified copy flash-synchro takeover show running-directory show reload show microcode show microcode history OmniSwitch 6250 CLI Reference Guide November 2009 page 1-1...
If the switch has a redundant CMM and the primary CMM is rebooted, the switch will fail over to the secondary CMM. For more information on CMM failover, see “Managing CMM Directories” in the OmniSwitch 6250 Switch Management Guide. •...
Page 35
Release History Release 6.6.1; command was introduced. Related Commands reload working Immediate primary CMM reboot to the working software configuration without secondary CMM takeover. MIB Objects chasEntPhysicalTable csEntPhysicalIndex chasEntPhysAdminStatus chasControlRedundantTable chasControlDelayedRebootTimer OmniSwitch 6250 CLI Reference Guide November 2009 page 1-3...
If a timeout is set, the switch reboots again after the set number of minutes, from the certified direc- tory. The reboot can be halted by issuing a cancel order as described in the reload command. page 1-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 37
-> reload working no rollback-timeout in 50 -> reload working rollback-timeout 10 at 12:50 Release History Release 6.6.1; command was introduced. Related Commands reload Reboots the CMM to its startup software configuration. MIB Objects chasControlModuleTable csEntPhysicalIndex chasControlActivateTimeout OmniSwitch 6250 CLI Reference Guide November 2009 page 1-5...
OmniSwitch set up with redundant CMMs. Examples -> configure copy running-config working Release History Release 6.6.1; command was introduced. page 1-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 39
Copies the running primary RAM version of the CMM software to the working primary flash. copy flash-synchro Copies the startup primary flash version of the CMM software to the startup secondary flash version of the CMM software. MIB Objects chasControlModuleTable csEntPhysicalIndex chasControlVersionMngt OmniSwitch 6250 CLI Reference Guide November 2009 page 1-7...
Or copy the startup primary flash version of the CMM software to the working primary flash. copy flash-synchro Copies the startup primary flash version of the CMM software to the startup secondary flash version of the CMM software. page 1-8 OmniSwitch 6250 CLI Reference Guide November 2009...
This command will not work if the switch is running from the certified directory. To view where the switch is running from, see the show running-directory command. Examples -> copy working certified -> copy working certified flash-synchro Release History Release 6.6.1; command was introduced. page 1-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 43
CMM software to the working primary flash. copy flash-synchro Copies the startup primary flash version of the CMM software to the star- tup secondary flash version of the CMM software. MIB Objects chasControlModuleTable csEntPhysicalIndex chasControlVersionMngt OmniSwitch 6250 CLI Reference Guide November 2009 page 1-11...
Copies the working primary flash version of the CMM software to cer- tified primary flash. Or copies the working primary flash version of the CMM software to startup secondary flash. MIB Objects chasControlModuleTable csEntPhysicalIndex chasControlVersionMngt page 1-12 OmniSwitch 6250 CLI Reference Guide November 2009...
OmniSwitch set up with redundant CMMs. Refer to the “NIs Reload On Takeover” description on page 1-16 for more information on the takeover command and redundant management modules. Examples -> takeover -> takeover with-fabric OmniSwitch 6250 CLI Reference Guide November 2009 page 1-13...
Page 46
CMM Commands Release History Release 6.6.1; command was introduced. Related Command reload Reboots the CMM to its startup software configuration. MIB Objects chasEntPhysicalTable csEntPhysicalIndex chasEntPhysAdminStatus page 1-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Running Configuration Where the switch is running from, either WORKING or CERTIFIED. A switch running from the certified directory will not be able to manip- ulate files in the directory structure. OmniSwitch 6250 CLI Reference Guide November 2009 page 1-15...
Page 48
Copies the running configuration (RAM) to the working directory. copy flash-synchro Copies the certified directory version of the primary CMM software to the certified directory of the secondary CMM. MIB Objects chasControlModuleTable chasControlRunningVersion chasControlActivateTimeout chasControlVersionMngt chasControlDelayedActivateTimer chasControlCertifyStatus chasControlSynchronizationStatus page 1-16 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands reload Reboots the primary or secondary CMM to its startup software configura- tion. reload working Immediate primary CMM reboot to the working software configuration without secondary CMM takeover. OmniSwitch 6250 CLI Reference Guide November 2009 page 1-17...
This command can also be used on the secondary CMM. Examples -> show microcode Package Release Size Description -----------------+---------------+--------+----------------------------------- Jbase.img 6.1.1.403.R01 10520989 Alcatel-Lucent Base Software Jos.img 6.1.1.403.R01 1828255 Alcatel-Lucent OS Jadvrout.img 6.1.1.403.R01 1359435 Alcatel-Lucent Advanced Routing page 1-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 51
Version number. Size File size. Description File description. Release History Release 6.6.1; command was introduced. Related Commands show microcode history Displays the archive history for microcode versions installed on the switch. OmniSwitch 6250 CLI Reference Guide November 2009 page 1-19...
Examples -> show microcode history Archive Created 8/27/05 23:45:00 Release History Release 6.6.1; command was introduced. Related Commands show microcode Displays microcode versions installed on the switch. page 1-20 OmniSwitch 6250 CLI Reference Guide November 2009...
MIB information for the Chassis Management and Monitoring commands is as follows: Filename: AlcatelIND1Chassis.mib Module: ALCATEL-IND1-CHASSIS-MIB Filename: AlcatelIND1System.MIB Module: ALCATEL-IND1-SYSTEM-MIB Filename: AlcatelIND1StackManager.MIB Module: ALCATEL-IND1-STACK-MANAGER-MIB OmniSwitch 6250 CLI Reference Guide November 2009 page 2-1...
Page 54
2-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Related Commands system name Modifies the switch’s current system name. system location Specifies the switch’s current physical location. show system Displays the basic system information for the switch. MIB Objects system systemContact OmniSwitch 6250 CLI Reference Guide November 2009 page 2-3...
Syntax Definitions text_string The new system name. The system name can range from 1 to 19 characters in length. Text strings that include spaces must be enclosed in quotation marks. For example, “OmniSwitch 6250”. Defaults Platforms Supported OmniSwitch 6250 Usage Guidelines Examples ->...
Specifies the switch’s administrative contact (e.g., an individual or a department). system name Modifies the switch’s current system name. show system Displays the basic system information for the switch. MIB Objects system systemLocation OmniSwitch 6250 CLI Reference Guide November 2009 page 2-5...
Release 6.6.1; command was introduced. Related Commands system time Displays or modifies the switch’s current system time. system timezone Displays or modifies the time zone for the switch. MIB Objects systemServices systemServicesDate page 2-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands system date Displays or modifies the switch’s current system date. system timezone Displays or modifies the time zone for the switch. MIB Objects systemServices systemServicesTime OmniSwitch 6250 CLI Reference Guide November 2009 page 2-7...
Be sure to periodically synchronize the primary and secondary CMMs using this command. • For detailed redundancy information refer to “Managing Stacks” in addition to “Managing CMM Directory Content” in the OmniSwitch 6250 Switch Management Guide. Examples -> system time-and-date synchro Release History Release 6.6.1;...
2:00 a.m. at 3:00 a.m. Japan +09:00 No default No default No default Korea +09:00 No default No default No default awst Australia West +08:00 No default No default No default OmniSwitch 6250 CLI Reference Guide November 2009 page 2-9...
Page 62
1st Sunday in Apr. at Last Sunday in Oct. 1:00 2:00 a.m. at 2:00 a.m. Hawaii -10:00 No default No default No default zm11 No standard name -11:00 No default No default No default page 2-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 63
Displays or modifies the switch’s current system date. system time Displays or modifies the switch’s current system time. MIB Objects systemServices systemServicesTimezone systemServicesTimezoneStartWeek systemServicesTimezoneStartDay systemServicesTimezoneStartMonth systemServicesTimezoneStartTime systemServicesTimezoneOffset systemServicesTimezoneEndWeek systemServicesTimezoneEndDay systemServicesTimezoneEndMonth systemServicesTimezoneEndTime systemServicesEnableDST OmniSwitch 6250 CLI Reference Guide November 2009 page 2-11...
If your timezone shows a default value in the DST Start and DST End columns of the “Time Zone and DST Information Table” found in Chapter 2, “Managing System Files,” of the OmniSwitch 6250 Switch Management Guide, you do not need to set a start and end time. Your switch clock will auto- matically adjust for DST as shown in the table.
Page 65
Displays or modifies the switch’s current system time. system timezone Displays or modifies the timezone for the switch. system date Displays or modifies the switch’s current system date. MIB Objects systemServices systemServicesTimezone systemServicesEnableDST OmniSwitch 6250 CLI Reference Guide November 2009 page 2-13...
Updates the uboot and the miniboot version on all available slots on all available switches within a stack. miniboot Updates the miniboot version. Defaults Platforms Supported OmniSwitch 6250 page 2-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 67
OS6400-> update fpga cmm OS6400-> update miniboot 3 Release History Release 6.6.1; command was introduced. Related Commands reload all Reloads all the NIs and CMMs in a chassis. MIB Objects systemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 2-15...
Chassis Management and Monitoring Commands update lanpower Uploads new firmware to the POE controller. Please contact your Alcatel-Lucent support representative before using this command. update lanpower {lanpower_num | all} Syntax Definitions lanpower_num The POE unit number to update. Updates all POE units in the switch.
Turns the power on or off for a specified Network Interface (NI) module. show ni Shows the hardware information and the current status for Network Interface (NI) modules currently running in the chassis. MIB Objects chasEntPhysicalTable chasEntPhysAdminStatus reset OmniSwitch 6250 CLI Reference Guide November 2009 page 2-17...
See examples below for further explanation. cancel Cancels a pending time delayed reload. Defaults Platforms Supported OmniSwitch 6250 Usage Guidelines Examples -> reload all Release History Release 6.6.1; command was introduced. page 2-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 71
Turns the power on or off for a specified Network Interface (NI) module. show ni Shows the hardware information and current status for Network Inter- face (NI) modules currently running in the chassis. MIB Objects chasEntPhysicalTable chasEntPhysAdminStatus reset OmniSwitch 6250 CLI Reference Guide November 2009 page 2-19...
To assign a unique saved slot number to a switch before rebooting, use the stack set slot command. Examples -> reload pass-through 1001 Release History Release 6.6.1; command was introduced. page 2-20 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 73
Displays the current operating topology of switches within a stack. stack set slot Assigns a new saved slot number to a switch in a stacked configuration. MIB Objects alaStackMgrChassisTable alaStackMgrSlotNINumber alaStackMgrCommandAction reloadPassThru OmniSwitch 6250 CLI Reference Guide November 2009 page 2-21...
Reloads (i.e., reboots) a specified Network Interface (NI) module. show ni Shows the hardware information and current status for Network Inter- face (NI) modules currently running in the chassis. MIB Objects chasEntPhysicalTable chasEntPhysAdminStatus powerOn powerOff page 2-22 OmniSwitch 6250 CLI Reference Guide November 2009...
-> temp-threshold 55 slot 2 Release History Release 6.6.1; command was introduced. Related Commands show temperature Displays the current operating chassis ambient temperature, as well as cur- rent temperature threshold settings. MIB Objects chasChassisTable chasTempThreshold OmniSwitch 6250 CLI Reference Guide November 2009 page 2-23...
To view the saved slot numbers currently assigned, use the show stack topology command. For detailed information on assigning saved slot numbers, as well as information on pass-through mode, refer to the OmniSwitch 6250 Series Hardware Users Guide. Examples -> stack set slot 2 saved-slot 3 ->...
Page 77
Clears the current saved slot information for a switch within a stacked configuration. show stack topology Displays the current operating topology of switches within a stack. MIB Objects alaStackMgrChassisTable alaStackMgrSlotNINumber alaStackMgrSavedSlotNINumber alaStackMgrCommandAction alaStackMgrCommandStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 2-25...
OmniSwitch 6250-Metro Models Usage Guidelines • The switch must be rebooted for the new mode to take affect. Examples -> stack set slot 2 mode stackable Release History Release 6.6.1; command was introduced. page 2-26 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 79
Chassis Management and Monitoring Commands Related Commands show stack mode Displays the current mode of the switches. MIB Objects alaStackMgrChassisTable alaStackMgrSlotNINumber alaStackMgrCommandAction alaStackMgrCommandStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 2-27...
Examples -> stack clear slot 1002 -> stack clear slot 3 immediate Release History Release 6.6.1; command was introduced. page 2-28 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 81
Sets the saved slot number for a switch in a stacked configuration. show stack topology Displays the current operating topology of switches within a stack. MIB Objects alaStackMgrChassisTable alaStackMgrSlotNINumber alaStackMgrSavedSlotNINumber alaStackMgrCommandAction alaStackMgrCommandStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 2-29...
An user-defined administrative contact for the switch. This field is modified using the system contact command. System Name A user-defined text description for the switch. This field is modified using the system name command. page 2-30 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 83
Specifies the switch’s administrative contact (e.g., an individual or a department). system name Modifies the switch’s current system name. system location Specifies the switch’s current physical location. MIB Objects system systemContact systemName systemLocation OmniSwitch 6250 CLI Reference Guide November 2009 page 2-31...
RAM size The total amount of RAM memory on the CMM. This field specifies the total RAM memory only and does not indicate the amount of mem- ory free or memory used. page 2-32 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 85
Displays the basic hardware and status information for CMM modules running in the chassis. MIB Objects systemHardware systemHardwareBootCpuType systemHardwareFlashMfg systemHardwareFlashSize systemHardwareMemoryMfg systemHardwareMemorySize systemHardwareNVRAMBatteryLow systemHardwareJumperInterruptBoot systemHardwareJumperForceUartDefaults systemHardwareJumperRunExtendedMemoryDiagnostics systemHardwareJumperSpare systemHardwareBootRomVersion systemHardwareBackupMiniBootVersion systemHardwareDefaultMiniBootVersion systemHardwareFpgaVersionTable systemHardwareFpgaVersionEntry systemHardwareFpgaVersionIndex OmniSwitch 6250 CLI Reference Guide November 2009 page 2-33...
Number Of Resets: Chassis 2 Model Name: OS6250-24, Description: 10/100/1000, Part Number: 902274-10, Hardware Revision: 004, Serial Number: 432L0008, Manufacture Date: SEP 08 2004, Admin Status: POWER ON, Operational Status: Number Of Resets: page 2-34 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 87
Description The factory-set description for the switch. This field cannot be modi- fied. Part Number The Alcatel-Lucent part number for the chassis. Hardware Revision The hardware revision level for the chassis. Serial Number The Alcatel-Lucent serial number for the chassis.
Description A factory-defined description of the associated board (e.g., BBUS Bridge or PROCESSOR). Part Number The Alcatel-Lucent part number for the board. Hardware Revision The hardware revision level for the board. Serial Number The Alcatel-Lucent serial number for the board.
Page 89
CMM is replaced or becomes secondary. The MAC address is used by the Chassis MAC Server (CMS) for allocation to various applications. Refer to the “Managing MAC Addresses and Ranges” chapter of the OmniSwitch 6250 Switch Management Guide for more information. Release History Release 6.6.1;...
CPU Model Type ARM926 (Rev 1), MAC Address: 00:e0:b1:c2:ee:89, ASIC - Physical 1: MV88F6281 Rev 2, FPGA - Physical 1: 0010/00, UBOOT Version : n/a, UBOOT-miniboot Version : 6.6.1.602.R01, POE SW Version : page 2-38 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 91
Part Number The Alcatel-Lucent part number for the NI. Hardware Revision The hardware revision level for the NI. Serial Number The Alcatel-Lucent serial number for the NI’s printed circuit board (PCB). Manufacture Date The date the NI was manufactured. Firmware Version The firmware version for the NI’s ASICs.
Page 92
Displays the detailed information for either a specified module or all modules installed in the chassis. show module status Displays the basic status information for either a specified module or all modules installed in the chassis. MIB Objects chasEntPhysOperStatus page 2-40 OmniSwitch 6250 CLI Reference Guide November 2009...
Hardware User Manual. Refer to page 2-36 for additional information on CMM location callouts. Part-Number The Alcatel-Lucent part number for the module. Serial # The Alcatel-Lucent serial number for the module. The hardware revision level for the module. Date The date the module was manufactured.
Page 94
Displays the detailed information for either a specified module or all modules installed in the chassis. show module status Displays the basic status information for either a specified module or all modules installed in the chassis. page 2-42 OmniSwitch 6250 CLI Reference Guide November 2009...
Power Control Checksum: 0x0, MAC Address: 00:d0:95:a3:e5:09, Module in slot 1 Model Name: OS6250-24, Description: 10/100/1000, Part Number: 902271-10, Hardware Revision: 002, Serial Number: E23L9059, Manufacture Date: JUN 08 2004, Firmware Version: N/A, OmniSwitch 6250 CLI Reference Guide November 2009 page 2-43...
Page 96
Part Number The Alcatel-Lucent part number for the NI. Hardware Revision The hardware revision level for the NI. Serial Number The Alcatel-Lucent serial number for the NI’s printed circuit board (PCB). Manufacture Date The date the NI was manufactured. Firmware Version The firmware version for NI’s ASICs.
For NI and secondary CMM modules, the operational status can be DOWN while the power status is on, indicating a possible software issue. Admin-Status The current power status of the module. Options include POWER ON or POWER OFF. OmniSwitch 6250 CLI Reference Guide November 2009 page 2-45...
Page 98
For the CMM, the base chassis MAC address is displayed. For detailed information on this base chassis MAC address, refer to the “Managing MAC Addresses and Ranges” chapter of the OmniSwitch 6250 Switch Management Guide. For NI modules, the MAC address for the corre- sponding NI is displayed.
Module in slot PS-5 (Power Shelf slot 5) Model Name: OS-IPS-600A, Description: ILPS AC, Part Number: 902252-10, Hardware Revision: A01, Serial Number: E51P4078, Manufacture Date: JAN 07 2005, Operational Status: Power Provision: OmniSwitch 6250 CLI Reference Guide November 2009 page 2-47...
Page 100
Description A description of the associated power supply. This field will reflect the model name in most cases. Part Number The Alcatel-Lucent part number for the power supply. Hardware Revision The hardware revision level for the power supply. Serial Number The Alcatel-Lucent serial number for the power supply.
Not Running Not Running output definitions Chassis The number of the switch in a stack. The fan number describing the fan position. Status The current operational status of the corresponding fan. OmniSwitch 6250 CLI Reference Guide November 2009 page 2-49...
Page 102
Chassis Management and Monitoring Commands Release History Release 6.6.1; command was introduced. Related Commands show temperature Displays the current operating chassis ambient temperature, as well as current temperature threshold settings. page 2-50 OmniSwitch 6250 CLI Reference Guide November 2009...
= N/A, Temperature Upper Threshold Range (deg C) = 15 to 80, Temperature Upper Threshold (deg C) = 57, Temperature Status = UNDER THRESHOLD, Temperature Danger Threshold (deg C) = 80 OmniSwitch 6250 CLI Reference Guide November 2009 page 2-51...
Page 104
Release 6.6.1; command was introduced. Related Commands temp-threshold Sets the chassis warning temperature threshold. show fan Shows the hardware information and current status for the chassis fans. MIB Objects chasChassisTable chasHardwareBoardTemp chasHardwareCpuTemp chasTempRange chasTempThreshold chasDangerTempThreshold page 2-52 OmniSwitch 6250 CLI Reference Guide November 2009...
IDLE (the switch does not have a management role but is operating normally as a network interface module within the stack), PASS-THRU (the switch is operating in pass-through mode), UNDEFINED (the switch’s current role is not known). OmniSwitch 6250 CLI Reference Guide November 2009 page 2-53...
Page 106
B’s remote end is connected to stacking port B on the other switch, the value displays StackB. If no stacking cable link exists, the value 0 displays. Release History Release 6.6.1; command was introduced. page 2-54 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 107
Displays the current redundant stacking cable status and token availabil- ity for a stacked configuration. MIB Objects alaStackMgrChassisTable alaStackMgrSlotNINumber alaStackMgrSlotCMMNumber alaStackMgrChasRole alaStackMgrLocalLinkStateA alaStackMgrRemoteNISlotA alaStackMgrRemoteLinkA alaStackMgrLocalLinkStateB alaStackMgrRemoteNISlotB alaStackMgrRemoteLinkB alaStackMgrChasState alaStackMgrSavedSlotNINumber alaStackMgrCommandAction alaStackMgrCommandStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 2-55...
For more information on stack redundancy, refer to the “Managing OmniSwitch 6250 Series Stacks” chapter in the OmniSwitch 6250 Series Hardware Users Guide.
The current management role of the corresponding switch: PRIMARY (the switch is the primary management module in the stack; standalone switches also display this role) SECONDARY (the switch is the secondary—or backup—management module in the stack) OmniSwitch 6250 CLI Reference Guide November 2009 page 2-57...
Page 110
"boot.slot.cfg" file. Release History Release 6.6.1; command was introduced. Related Commands stack set slot mode Changes the stacking/standalone mode of the switch. MIB Objects alaStackMgrChassisTable alaStackMgrSlotNINumber alaStackMgrSlotCMMNumber alaStackMgrChasRole alaStackMgrChasState alaStackMgrCommandAction alaStackMgrCommandStatus page 2-58 OmniSwitch 6250 CLI Reference Guide November 2009...
MIB information for the Chassis MAC Server commands is as follows: Filename: AlcatelIND1MacServer.MIB Module: Alcatel-IND1-MAC-SERVER-MIB A summary of the available commands is listed here: mac-range eeprom mac-retention status mac-retention dup-mac-trap mac release show mac-range show mac-range alloc show mac-retention status OmniSwitch 6250 CLI Reference Guide November 2009 page 3-1...
Modifies the default MAC range on the switch’s EEPROM. Note. Use caution when modifying the default MAC range. Improper use of this command can disable your system and adversely affect your network. Contact Alcatel-Lucent Customer Support for further assistance. mac-range eeprom start_mac_address count...
Page 113
Chassis MAC Server (CMS) Commands Related Commands show mac-range Displays the MAC range table. MIB Objects chasMacAddressRangeTable chasMacRangeIndex chasGlobalLocal chasMacAddressStart chasMacAddressCount OmniSwitch 6250 CLI Reference Guide November 2009 page 3-3...
When the administrative status of MAC retention is enabled, the stack performance is enhanced. Examples -> mac-retention status enable Release History Release 6.2.1; command was introduced. Related Commands show mac-retention status Displays the MAC retention status. MIB Objects chasMacAddrRetentionObjects chasMacAddrRetentionStatus page 3-4 OmniSwitch 6250 CLI Reference Guide November 2009...
SNMP trap will be generated. Examples -> mac-retention dup-mac-trap enable Release History Release 6.2.1; command was introduced. Related Commands show mac-retention status Displays the MAC retention status. MIB Objects chasMacAddrRetentionObjects chasPossibleDuplicateMacTrapStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 3-5...
MAC address of the old primary switch). Examples -> mac release Release History Release 6.2.1; command was introduced. Release 6.3.1; mac-retention keyword was replaced with the mac keyword. Related Commands MIB Objects chasMacAddrRetentionObjects chasMacAddrRetentionStatus page 3-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Start Mac Addr The first MAC address in the MAC address range. End Mac Addr The last MAC address in the MAC address range. Release History Release 6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 3-7...
Page 118
Chassis MAC Server (CMS) Commands Related Commands mac-range eeprom Modifies the default MAC range on the switch’s EEPROM. MIB Objects chasMacAddressRangeTable chasMacRangeIndex chasGlobalLocal chasMacAddressStart chasMacAddressCount chasMacRowStatus page 3-8 OmniSwitch 6250 CLI Reference Guide November 2009...
MAC range table. Values may range from 1–20. MAC ranges are divided by index number into four distinct cate- gories. Refer to page 3-7 for more information. Mac Address Current MAC address allocated for a specific application. OmniSwitch 6250 CLI Reference Guide November 2009 page 3-9...
Page 120
VLAN 1 is assigned the ID value 0. Release History Release 6.1; command was introduced. Related Commands mac-range eeprom Modifies the default MAC range on the switch’s EEPROM. MIB Objects ChasMacAddressAllocTable chasAppId chasObjectId chasAllocMacRangeIndex chasAllocMacAddress page 3-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Displays the source of the currently used MAC address. Options include EEPROM and Retained. Topology Status Displays the topology status of the stack. Options include Ring present and Ring Not Present. OmniSwitch 6250 CLI Reference Guide November 2009 page 3-11...
Page 122
Release 6.3.1; EEPROM MAC Address field was deleted. Related Commands mac-retention status Enables or disables the MAC retention status. mac-retention dup-mac-trap Enables or disables the duplicate MAC address trap status. MIB Objects chasMacAddrRetentionObjects chasMacAddrRetentionStatus chasPossibleDuplicateMacTrapStatus chasRingStatus chasBaseMacAddrSource chasBaseMacAddr page 3-12 OmniSwitch 6250 CLI Reference Guide November 2009...
4 Power over Ethernet (PoE) Commands The Power over Ethernet (PoE) feature is supported on the OmniSwitch 6250-P24 switch. Refer to the OmniSwitch 6250 Hardware Users Guide and OmniSwitch 6250 Hardware Users Guide for further details. Note on Terminology. There are several general terms used to describe this feature. The terms Power over Ethernet (PoE), Power over LAN (PoL), Power on LAN (PoL), and Inline Power are synonymous terms used to describe the powering of attached devices via Ethernet ports.
Page 125
PoE ports in a specified slot. show lanpower Displays current inline power status and related statistics for all PoE ports in a specified slot. MIB Objects alaPethMainPseGroup alaPethMainPseAdminStatus pethPsePortTable pethPsePortAdminEnable OmniSwitch 6250 CLI Reference Guide November 2009 page 4-3...
PoE ports in a specified slot. lanpower combo-port Displays current inline power status and related statistics for all PoE ports in a specified slot. MIB Objects alaPethMainPseGroup alaPethMainPseAdminStatus pethPsePortTable pethPsePortAdminEnable page 4-4 OmniSwitch 6250 CLI Reference Guide November 2009...
(mW); the related command, lanpower maxpower, is specified in watts (W). Examples -> lanpower 3/1 power 3025 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 4-5...
Page 128
PoE ports in a specified slot. lanpower combo-port Displays current inline power status and related statistics for all PoE ports in a specified slot. MIB Objects alaPethPsePortTable alaPethPsePortPowerMaximum page 4-6 OmniSwitch 6250 CLI Reference Guide November 2009...
(W); the related command, lanpower power, is specified in milliwatts (mW). Examples -> lanpower 3 maxpower 200 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 4-7...
Page 130
Specifies the maximum amount of inline power, in milli- watts, allocated to a specific PoE port. lanpower combo-port Displays current inline power status and related statistics for all PoE ports in a specified slot. MIB Objects alaPethMainPseGroup alaPethMainPseMaxPower page 4-8 OmniSwitch 6250 CLI Reference Guide November 2009...
(i.e., before critical- and high-priority ports). Defaults parameter default low | high | critical Platforms Supported OmniSwitch 6250-Enterprise Models Usage Guidelines Examples -> lanpower 2/16 priority low Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 4-9...
Page 132
Power over Ethernet (PoE) Commands Related Commands lanpower combo-port Displays current inline power status and related statistics for all PoE ports in a specified slot. MIB Objects pethPsePortGroup pethPsePortPowerPriority page 4-10 OmniSwitch 6250 CLI Reference Guide November 2009...
PoE power budget for an additional device. For detailed information on this function, refer to the “Managing Power over Ethernet (PoE)” chapter in the OmniSwitch 6250 Series Hardware Users Guide. lanpower slot priority-disconnect {enable | disable}...
Page 134
Specifies an inline power priority level to a port. Levels include critical, high, and low. show lanpower priority-disconnect Displays the priority disconnect function status on all ports in a specified slot. MIB Objects alaPethMainPseTable alaPethMainPsePriorityDisconnect page 4-12 OmniSwitch 6250 CLI Reference Guide November 2009...
-> lanpower 1 combo-port enable Release History Release 6.6.1; command was introduced. Related Commands show lanpower Displays current inline power status and related statistics for all PoE ports in a specified slot. MIB Objects OmniSwitch 6250 CLI Reference Guide November 2009 page 4-13...
The actual amount of power being used by an attached device (if appli- cable), in milliwatts. If no device is attached to the corresponding port, this row displays a value of 0. page 4-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 137
Class ??? Need Info. Release History Release 6.6.1; command was introduced. Related Commands MIB Objects alaPethMainPseGroup alaPethMainPseAdminStatus pethPsePortTable pethPsePortAdminEnable alaPethPsePortTable alaPethPsePortPowerMaximum alaPethMainPseGroup alaPethMainPseMaxPower pethMainPsePower pethPsePortGroup pethPsePortPowerPriority OmniSwitch 6250 CLI Reference Guide November 2009 page 4-15...
Slot 2 Priority Disconnect Enabled! Release History Release 6.6.1; command was introduced. Related Commands lanpower priority-disconnect Enables or disables the priority disconnect function on all ports in a specified slot. MIB Objects alaPethMainPseTable alaPethMainPsePriorityDisconnect OmniSwitch 6250 CLI Reference Guide November 2009 page 4-17...
Page 140
Power over Ethernet (PoE) Commands page 4-18 OmniSwitch 6250 CLI Reference Guide November 2009...
(.txt) located on the server. This file must be on both the server and the local switch, and match, for authentication to work. Enter the key identification using the key keyword if the server is set to MD5 authentication. page 5-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 143
-> no ntp server 1.1.1.1 Release History Release 6.6.1; command was introduced. Related Commands ntp client Enables or disables NTP operation on the switch. MIB Objects alaNtpConfig alaNtpPeerAddressType alaNtpPeerType alaNtpPeerAuth alaNtpPeerVersion alaNtpPeerMinpoll alaNtpPeerPrefer alaNtpPeerAddress OmniSwitch 6250 CLI Reference Guide November 2009 page 5-3...
Disables an NTP client from invoking tests for NTP server synchroniza- tion. This allows the NTP client to synchronize with unsynchronized NTP servers in the network. MIB Objects alaNtpConfig alaNtpPeerTests page 5-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands ntp server synchronized Enables an NTP client to invoke tests for NTP server synchronization as specified by the NTP protocol. MIB Objects alaNtpConfig alaNtpPeerTests OmniSwitch 6250 CLI Reference Guide November 2009 page 5-5...
-> ntp client enable -> ntp client disable Release History Release 6.6.1; command was introduced. Related Commands ntp server Specifies an NTP server from which the switch will receive updates. MIB Objects alaNtpEnable page 5-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Examples -> ntp key 5 trusted -> ntp key 2 untrusted Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 5-9...
Page 150
Related Commands ntp key Sets the public key the switch uses when authenticating with the specified NTP server. ntp client Enables or disables authentication on the switch. MIB Objects alaNtpAccessKeyIdTable alaNtpAccessKeyIdKeyId alaNtpAccessKeyIdTrust page 5-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands ntp key Labels the specified authentication key identification as trusted or untrusted. ntp server Specifies an NTP server from which this switch will receive updates. MIB Objects alaNtpAccessRereadkeyFile OmniSwitch 6250 CLI Reference Guide November 2009 page 5-11...
What NTP mode the client is running in, either client or broadcast. Broadcast delay The number of microseconds in the advertised broadcast delay time. This field is absent if the client broadcast mode is disabled. Release History Release 6.6.1; command was introduced. page 5-12 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 153
Network Time Protocol Commands Related Command ntp client Enables or disables NTP operation on the switch. MIB Objects alaNtpLocalInfo OmniSwitch 6250 CLI Reference Guide November 2009 page 5-13...
The delay received from the server in its timestamp. Offset The offset received from the server in its timestamp. Disp The dispersion value received from the server in its timestamp. Release History Release 6.6.1; command was introduced. page 5-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 155
Network Time Protocol Commands Related Command ntp client Enables or disables authentication on the switch. MIB Objects alaNtpPeerListTable OmniSwitch 6250 CLI Reference Guide November 2009 page 5-15...
Page 157
Number of duplicated packets received. Bogus origin Number of bogus packets. Bad authentication Number of NTP packets rejected for not meeting the authentication standards. Bad dispersion Number of bad dispersions. Last Event The last event. OmniSwitch 6250 CLI Reference Guide November 2009 page 5-17...
Page 158
Network Time Protocol Commands Release History Release 6.6.1; command was introduced. Related Command ntp client Enables or disables authentication on the switch. MIB Objects alaNtpPeerListTable alaNtpPeerShowStatus page 5-18 OmniSwitch 6250 CLI Reference Guide November 2009...
The key number corresponding to a key in the key file. Status Whether the key is trusted or untrusted. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 5-19...
Page 160
Network Time Protocol Commands Related Command ntp key Labels the specified authentication key identification as trusted or untrusted. ntp key load Loads the current key file into memory. MIB Objects alaNtpAccessKeyIdTable page 5-20 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 161
HTTP Total Sessions SNMP MIB information for commands in this chapter are as follows: Filename: AlcatelInd1SessionMgr.mib Module: AlcatelIND1SessionMgrMIB Filename: AlcatelIND1AAA.mib Module: Alcatel-IND1-AAA-MIB Filename: AlcatelIND1System.mib Module: Alcatel-IND1ConfigMgr.mib Filename: AlcatelIND1Ssh.mib Module: ALCATEL-IND1-SSH-MIB OmniSwitch 6250 CLI Reference Guide November 2009 page 6-1...
Configures the inactivity timer for a CLI, HTTP (including Web- View), or FTP interface. When the switch detects no user activity for this period of time, the user is logged off the switch. MIB Objects sessionMgr sessionLoginAttempt OmniSwitch 6250 CLI Reference Guide November 2009 page 6-3...
Configures the inactivity timer for a CLI, HTTP (including Web- View), or FTP interface. When the switch detects no user activity for this period of time, the user is logged off the switch. MIB Objects sessionMgr sessionLoginTimeout page 6-4 OmniSwitch 6250 CLI Reference Guide November 2009...
The session banner command is used to configure or modify the banner file name. You must use a text editor to edit the file containing the banner text. Examples -> session banner cli/switch/banner.txt Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 6-5...
Page 166
Session Management Commands Related Commands show session config Displays Session Manager information such as banner file name, session timeout value, and default prompt value. MIB Objects SessionConfigTable SessionType SessionBannerFileName page 6-6 OmniSwitch 6250 CLI Reference Guide November 2009...
If you change the timer, the new value does not affect current sessions; the new timer is applied to new sessions only. Examples -> session timeout cli 5 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 6-7...
Page 168
Session Management Commands Related Commands show session config Displays Session Manager information, such as banner file name, session timeout value, and default prompt value. MIB Objects SessionConfigTable SessionType SessionInactivityTimerValue page 6-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands show session config Displays Session Manager information such as banner file name, session timeout value, and default prompt value. MIB Objects SessionConfigTable SessionType sessionDefaultPromptString OmniSwitch 6250 CLI Reference Guide November 2009 page 6-9...
-> session xon-xoff disable Release History Release 6.6.1; command was introduced. Related Commands show session xon-xoff Displays whether the console port is enabled or disabled for XON- XOFF. MIB Objects sessionXonXoffEnable page 6-10 OmniSwitch 6250 CLI Reference Guide November 2009...
To set the CLI prompt back to the arrow (->), enter the prompt string -> (prompt string dash greater- than) syntax. Examples -> prompt user -> prompt user time date -> prompt prefix -> prompt string 12-> -> prompt prefix -> Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 6-11...
Page 172
Session Management Commands Related Commands show prefix Shows the command prefix (if any) currently stored by the CLI. Prefixes are stored for command families that support the prefix recognition feature. MIB Objects page 6-12 OmniSwitch 6250 CLI Reference Guide November 2009...
Release History Release 6.6.1; command was introduced. Related Commands prompt This command defines the format of the CLI prompt. The prompt can be defined to include the command prefix. MIB Objects OmniSwitch 6250 CLI Reference Guide November 2009 page 6-13...
To reset commands set with alias back to their factory default, use the user profile reset command. Examples -> alias gp group -> alias privilege attrib Release History Release 6.6.1; command was introduced. page 6-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 175
Lists all current commands defined by the use of the alias CLI command. user profile reset Resets the alias, prompt, and more values to their factory defaults. MIB Objects OmniSwitch 6250 CLI Reference Guide November 2009 page 6-15...
-> show alias group privilege: attrib Release History Release 6.6.1; command was introduced. Related Commands alias Defines substitute command text for the switch’s CLI command keywords. MIB Objects page 6-16 OmniSwitch 6250 CLI Reference Guide November 2009...
Defines substitute command text for the switch’s CLI command keywords. more size Specifies the number of lines that your console screen will display. user profile reset Resets the alias, prompt and more values to their factory defaults. MIB Objects OmniSwitch 6250 CLI Reference Guide November 2009 page 6-17...
Specifies the number of lines that your console screen will display. user profile save Saves the user account settings for aliases, prompts and the more screen. MIB Objects page 6-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Displays commands that you have recently issued to the switch. The commands are displayed in a numbered list. Recalls commands listed in the history buffer and displays them at the CLI prompt. MIB Objects OmniSwitch 6250 CLI Reference Guide November 2009 page 6-19...
The number of commands currently stored in the history buffer for this session. Index Range The index range of the commands for this CLI session currently stored in the history buffer. Release History Release 6.6.1; command was introduced. page 6-20 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 181
Sets the number of commands that will be stored in the CLI’s history buffer. Recalls commands listed in the history buffer and displays them at the CLI prompt. MIB Objects OmniSwitch 6250 CLI Reference Guide November 2009 page 6-21...
Page 182
-> show history 1* show cmm 2 show fan 3 show sensor 4 show temp 5 show time 6 show arp 7 clear arp Release History Release 6.6.1; command was introduced. page 6-22 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 183
Sets the number of commands that will be stored in the CLI’s history buffer. show history Displays commands you have recently issued to the switch. The com- mands are displayed in a numbered list. MIB Objects OmniSwitch 6250 CLI Reference Guide November 2009 page 6-23...
Related Commands show ssh config Displays the contents of the command.log file. show command-log status Shows the current status of the command logging function (i.e., enabled or disabled). MIB Objects sessionCliCommandLogEnable page 6-24 OmniSwitch 6250 CLI Reference Guide November 2009...
6-28 for a listing of valid families. Read-Write domains The command domains available with the user’s read-write access. See the table beginning on page 6-28 for a listing of valid domains. OmniSwitch 6250 CLI Reference Guide November 2009 page 6-27...
Page 188
Release History Release 6.6.1; command was introduced. Related Commands Displays all active login sessions (e.g., Console, Telnet, FTP, HTTP, Secure Shell, and Secure Shell FTP). kill Kills another user’s session. page 6-28 OmniSwitch 6250 CLI Reference Guide November 2009...
The session number assigned to the user. User name User name. Access type Type of access protocol used to connect to the switch. Access port Switch port used for access during this session. page 6-30 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 191
Release History Release 6.6.1; command was introduced. Related Commands whoami Displays current user session. kill Kills another user’s session. MIB Objects SessionActive sessionIndex sessionAccessType sessionPhysicalPort sessionUserName sessionUserReadPrivileges sessionUserWritePrivileges sessionUserProfileNumber sessionUserIpAddress sessionRowStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 6-31...
Http Inactivity Timer in Inactivity timer value (in minutes) for HTTP (including WebView) minutes sessions. The user is logged off when this value is exceeded. page 6-32 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 193
TCP connection is closed. session login-timeout Sets the amount of time the user can take to accomplish a successful login to the switch. MIB Objects SessionConfigTable sessionType sessionBannerFileName sessionInactivityTimerValue sessionDefaultPromptString OmniSwitch 6250 CLI Reference Guide November 2009 page 6-33...
Examples -> show session xon-xoff XON-XOFF Enabled Release History Release 6.6.1; command was introduced. Related Commands session xon-xoff Enables/disables the XON-XOFF protocol on the console port. MIB Objects sessionXonXoffEnable page 6-34 OmniSwitch 6250 CLI Reference Guide November 2009...
Enables the more mode for your console screen display. show more Shows the enable status of the more mode along with the number of lines specified for the screen display. MIB Objects SystemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 6-35...
Shows the number of TTY lines and columns to be displayed. more size Specifies the number of lines that your console screen will display. MIB Objects SystemServices systemServicesArg1 systemServicesAction page 6-36 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands more Enables the more mode for your console screen display. more size Specifies the number of lines that your console screen will display. MIB Objects SystemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 6-37...
You can establish up to 5 concurrent IPv4 or IPv6 telnet client sessions. • You can establish up to 4 concurrent IPv4 or IPv6 telnet sessions towards an OmniSwitch 6250 (i.e. when the switch acts as a telnet server). Examples ->...
Page 199
IPv6 network Invokes the Secure Shell on the switch. A Secure Shell is used to make a secured connection to a remote system or device. MIB Objects SystemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 6-39...
You can establish up to 5 concurrent IPv4 or IPv6 telnet client sessions. • You can establish up to 4 concurrent IPv4 or IPv6 telnet sessions towards an OmniSwitch 6250 (i.e. when the switch acts as a telnet server). Examples ->...
Page 201
Invokes a Telnet session. A Telnet session is used to connect to a remote system or device. ssh6 Invokes Secure Shellv6 on the switch. Secure Shellv6 is used to make a secured connection to an SSHv6 server. MIB Objects SystemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 6-41...
You can establish up to 1 SSH sessions from an OmniSwitch (when it acts as Client) and up to 8 SSH sessions towards an OmniSwitch (when it acts as Server). Examples -> ssh enable -> ssh 172.155.11.211 login as: Release History Release 6.6.1; command was introduced. page 6-42 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 203
Invokes Secure Shellv6 on the switch. Secure Shellv6 is used to make a secured connection to an SSHv6 server. show ssh config Displays the status of Secure Shell, SCP/SFTP on the switch. MIB Objects aaaAcctSATable aaacsInterface alaSshConfigGroup alaSshAdminStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 6-43...
At anytime, there can be only a single SSH client session (either SSHv4 or SSHv6) to any SSH server. Examples -> ssh6 fe80::a00:20ff:fea8:8961 int1 -> ssh6 ::1 -> ssh6 Sun.com Release History Release 6.6.1; command was introduced. page 6-44 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 205
Invokes Secure Shell on the switch. Secure Shell is used to make a secured connection to a remote system or device. show ssh config Displays the status of Secure Shell, SCP/SFTP on the switch. MIB Objects aaaAcctSATable aaacsInterface alaSshConfigGroup alaSshAdminStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 6-45...
Invokes a Telnet session. A Telnet session is used to connect to a remote system or device. sftp Starts an SFTP session. An SFTP session provides a secure file transfer method. MIB Objects alaSshConfigGroup alaSshPubKeyEnforceAdminStatus page 6-46 OmniSwitch 6250 CLI Reference Guide November 2009...
Displays the SCP/SFTP status (enabled or disabled). Public Key Authentication Displays whether the Public Key Authentication is enforced. Options Enforced include true or false. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 6-47...
Page 208
Enables or disables secure copy (SCP) and secure FTP (SFTP) at the same time on the switch. MIB Objects alaSshConfigGroup alaSshAdminStatus alaScpSftpAdminStatus alaSshPubKeyEnforceAdminStatus page 6-48 OmniSwitch 6250 CLI Reference Guide November 2009...
: ERROR: Ip Address must not belong to IP VLAN 44 subnet Command : command-log enable UserName : admin Date : FRI JAN 09 00:18:49 Ip Addr : 128.251.19.240 Result : SUCCESS OmniSwitch 6250 CLI Reference Guide November 2009 page 6-49...
Page 210
“Managing Switch User Accounts” chapter in the OmniSwitch 6250 Switch Management Guide. Date The date and time, down to the second, when the command was entered.
Release History Release 6.6.1; command was introduced. Related Commands command-log Enables or disables command logging on the switch. show ssh config Displays the contents of the command.log file. MIB Objects sessionCliCommandLogStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 6-51...
Other commands allow you to change command privileges and to monitor the switch’s memory. MIB information for the system commands is as follows: Filename: AlcatelIND1System.mib Module: ALCATEL-IND1-SYSTEM-MIB Filename: AlcatelIND1Chassis.mib Module: ALCATEL-IND1-CHASSIS-MIB Filename: AlcatelIND1Ssh.mib Module: ALCATEL-IND1-SSH-MIB OmniSwitch 6250 CLI Reference Guide November 2009 page 7-1...
Page 214
A summary of the available commands is listed here: File System mkdir rmdir rename delete move chmod attrib freespace fsck newfs System Services view show tty more ftp6 show ssh config sftp sftp6 tftp page 7-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 215
File and directory names can include only the following character types: a-z, A-Z, 0-9, dashes (-), dots (.), and underscores (_). • This command can also be used on the secondary CMM. Examples -> cd -> cd test_path Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 7-3...
Page 216
Deletes an existing directory. Displays the contents of a specified directory or the current working directory. Displays the contents of a specified directory or the current working directory. MIB Objects systemServices systemServicesWorkingDirectory page 7-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Deletes an existing directory. Displays the contents of a specified directory or the current working directory. Displays the contents of a specified directory or the current working directory. MIB Objects systemServices systemServicesWorkingDirectory OmniSwitch 6250 CLI Reference Guide November 2009 page 7-5...
File and directory names can include only the following character types: a-z, A-Z, 0-9, dashes (-), dots (.), and underscores (_). • This command can also be used on the secondary CMM. Examples -> mkdir test_directory -> mkdir flash/test_directory Release History Release 6.6.1; command was introduced. page 7-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 219
Deletes an existing directory. Displays the contents of a specified directory or the current working directory. Displays the contents of a specified directory or the current working directory. MIB Objects systemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-7...
Up to 255 characters may be used for the specified path. • This command can also be used on the secondary CMM. Examples -> rmdir ../working -> rmdir flash/working Release History Release 6.6.1; command was introduced. page 7-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 221
Creates a new directory. Displays the contents of a specified directory or the current working directory. Displays the contents of a specified directory or the current working directory. MIB Objects systemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-9...
Page 222
File and directory names can include only the following character types: a-z, A-Z, 0-9, dashes (-), dots (.), and underscores (_). • This command can also be used on the secondary CMM. page 7-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 223
Displays the switch’s current working directory. mkdir Creates a new directory. rmdir Deletes an existing directory. Displays the contents of a specified directory or the current working directory. MIB Objects systemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-11...
File and directory names can include only the following character types: a-z, A-Z, 0-9, dashes (-), dots (.), and underscores (_). • This command can also be used on the secondary CMM. page 7-12 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 225
Displays the switch’s current working directory. mkdir Creates a new directory. rmdir Deletes an existing directory. Displays the contents of a specified directory or the current working directory. MIB Objects systemServices systemServicesArg22 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-13...
File and directory names can include only the following character types: a-z, A-Z, 0-9, dashes (-), dots (.), and underscores (_). • This command can also be used on the secondary CMM. Examples -> rename flash/working/asc.1.snap new_file Release History Release 6.6.1; command was introduced. page 7-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 227
Copies an existing file or directory. Moves an existing file or directory to a new location. move Moves an existing file or directory to a new location. MIB Objects systemServices systemServicesArg1 systemServicesArg2 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-15...
Page 228
This command can also be used on the secondary CMM. Examples -> rm test_config_file -> rm flash/test_config_file Release History Release 6.6.1; command was introduced. Related Commands delete Deletes an existing file. page 7-16 OmniSwitch 6250 CLI Reference Guide November 2009...
This command can also be used on the secondary CMM. Examples -> delete test_config_file -> delete flash/test_config_file Release History Release 6.6.1; command was introduced. Related Commands Deletes an existing file or directory. MIB Objects systemServices systemServicesArg1 systemServicesAction page 7-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 231
File and directory names can include only the following character types: a-z, A-Z, 0-9, dashes (-), dots (.), and underscores (_). • This command can also be used on the secondary CMM. OmniSwitch 6250 CLI Reference Guide November 2009 page 7-19...
Page 232
-> cp asc.1.snap flash/snapshot/snapshot_copy -> cp asc.1.snap snapshot_copy Release History Release 6.6.1; command was introduced. Related Commands Moves an existing file or directory to a new location. MIB Objects systemServices systemServicesArg1 systemServicesArg2 systemServicesAction page 7-20 OmniSwitch 6250 CLI Reference Guide November 2009...
File and directory names can include only the following character types: a-z, A-Z, 0-9, dashes (-), dots (.), and underscores (_). • If SCP is not enabled, use the ftp6 command to enable it. • SCP is not supported between OmniSwitch and Windows currently. OmniSwitch 6250 CLI Reference Guide November 2009 page 7-21...
Page 234
Fetching /flash/working/Ksecu.img to /flash/working/Ksecu.img Connection to 172.17.11.13 closed. Release History Release 6.6.1; command was introduced. Related Commands Moves an existing file or directory to a new location. MIB Objects systemServices systemServicesArg1 systemServicesArg2 systemServicesAction page 7-22 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 235
File and directory names can include only the following character types: a-z, A-Z, 0-9, dashes (-), dots (.), and underscores (_). • This command can also be used on the secondary CMM. Examples -> mv flash/asc.1.snap flash/backup_files/asc.1.snap OmniSwitch 6250 CLI Reference Guide November 2009 page 7-23...
Page 236
File Management Commands Release History Release 6.6.1; command was introduced. Related Commands rename Renames an existing file or directory. Copies an existing file or directory. MIB Objects systemServices systemServicesArg1 systemServicesArg2 systemServicesAction page 7-24 OmniSwitch 6250 CLI Reference Guide November 2009...
File and directory names can include only the following character types: a-z, A-Z, 0-9, dashes (-), dots (.), and underscores (_). • This command can also be used on the secondary CMM. Examples -> move flash/asc.1.snap flash/backup_files/asc.1.snap OmniSwitch 6250 CLI Reference Guide November 2009 page 7-25...
Page 238
File Management Commands Release History Release 6.6.1; command was introduced. Related Commands rename Renames an existing file or directory. Copies an existing file or directory. MIB Objects systemServices systemServicesArg1 systemServicesArg2 systemServicesAction page 7-26 OmniSwitch 6250 CLI Reference Guide November 2009...
If the fsck command detects a problem with the /flash file system, a message is displayed indicating the problem, along with any steps needed to resolve it. MIB Objects SystemFileSystemTable systemFileSystemFreespace OmniSwitch 6250 CLI Reference Guide November 2009 page 7-29...
# of bad clusters: total free space: 77,357,056 max contiguous free space: 55,451,648 bytes # of files: # of folders: total bytes in files: 44,357,695 # of lost chains: total bytes in lost chains: page 7-30 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 243
Release History Release 6.6.1; command was introduced. Related Commands freespace Displays the amount of free space available in the /flash directory. MIB Objects systemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-31...
• This command can also be used on the secondary CMM. Examples -> newfs /flash Release History Release 6.6.1; command was introduced. Related Commands MIB Objects systemServices systemServicesArg1 systemServicesAction page 7-32 OmniSwitch 6250 CLI Reference Guide November 2009...
Removes a file from a secondary CMM or from a non-primary switch in a stack. Displays the content of a non primary CMM in a switch or a non-pri- mary switch in a stack. MIB Objects chasSupervisionRfsLsTable alcatelIND1ChassisSupervisionRfsCommands chasSupervisionRfsCommandsSlot chasSupervisionRfsCommandsCommand chasSupervisionRfsCommandsSrcFileName chasSupervisionRfsCommandsDestFileName OmniSwitch 6250 CLI Reference Guide November 2009 page 7-33...
Copies a file from a non-primary switch to a primary switch in a stack. Displays the content of a non primary CMM in a switch or anon-pri- mary switch in a stack. MIB Objects chasSupervisionRfsLsTable alcatelIND1ChassisSupervisionRfsCommands chasSupervisionRfsCommandsSlot chasSupervisionRfsCommandsCommand chasSupervisionRfsCommandsSrcFileName page 7-34 OmniSwitch 6250 CLI Reference Guide November 2009...
3 11:20 cs_system.pmd 394632 1980 bootrom.bin 511096 1980 miniboot.backup 511096 1980 miniboot.default 2048 Feb 25 06:34 network/ 2048 3 11:29 switch/ 3 11:29 random-seed Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 7-35...
Page 248
Removes a file from a secondary CMM or from a non-primary switch in a stack. MIB Objects chasSupervisionRfsLsTable chasSupervisionRfsLsFileIndex chasSupervisionRfsLsSlot chasSupervisionRfsLsDirName chasSupervisionRfsLsFileName chasSupervisionRfsLsFileType chasSupervisionRfsLsFileSize chasSupervisionRfsLsFileAttr chasSupervisionRfsLsFileDateTime page 7-36 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 249
Release 6.6.1; command was introduced. Related Commands view Allows you to view the contents of a specified file by invoking the Vi text editor in read-only mode. MIB Objects systemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-37...
This command can also be used on the secondary CMM. Examples -> view flash/text_file.txt Release History Release 6.6.1; command was introduced. Related Commands Launches the switch’s Vi text editor. MIB Objects systemServices systemServicesArg1 systemServicesAction page 7-38 OmniSwitch 6250 CLI Reference Guide November 2009...
The values set with this command do not control the CLI screen when the switch is operating in normal mode. • This command can also be used on the secondary CMM. Examples -> tty 10 60 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 7-39...
Page 252
File Management Commands Related Commands show tty Displays current TTY settings. more Displays a switch text file onto the console screen. MIB Objects systemServices systemServicesTtyLines systemServicesTtyColumns page 7-40 OmniSwitch 6250 CLI Reference Guide November 2009...
= 24, columns = 80 Release History Release 6.6.1; command was introduced. Related Commands Specifies the number of TTY lines and columns to be displayed. MIB Objects systemServices systemServicesTtyLines systemServicesTtyColumns OmniSwitch 6250 CLI Reference Guide November 2009 page 7-41...
This command can also be used on the secondary CMM. Examples -> more config_file1 -> more flash/config_file1 -> more flash/working/config_file1 Release History Release 6.6.1; command was introduced. Related Commands Specifies the number of TTY lines and columns to be displayed. page 7-42 OmniSwitch 6250 CLI Reference Guide November 2009...
List the commands that the remote FTP server supports. user Send new user information. lpwd Display the current working directory on the local host. Display list of available FTP commands. page 7-44 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 257
220 Annex FTP server (Version RA4000 R14.1.15) ready. Name : Release History Release 6.6.1; command was introduced. Related Commands sftp Starts an SFTP session. ftp6 Starts an FTPv6 session. MIB Objects systemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-45...
Print the hash symbol (#) for every block of data transferred. (This com- mand toggles hash enabling and disabling.) help Display list of available FTP commands. Change to a new directory on the local machine. page 7-46 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 259
-> ftp6 fe80::a00:20ff:fea8:8961 int3 -> ftp6 ::5 -> ftp6 Sun.com Release History Release 6.6.1; command was introduced. Related Commands sftp6 Starts an SFTPv6 session. Starts an FTP session. MIB Objects systemServices systemServicesArg1 systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-47...
Invokes Secure Shell on the switch. Secure Shell is used to make a secured connection to a remote system or device. show ssh config Displays the status of Secure Shell, SCP/SFTP on the switch. MIB Objects alaSshConfigGroup alaScpSftpAdminStatus page 7-48 OmniSwitch 6250 CLI Reference Guide November 2009...
Invokes Secure Shell on the switch. Secure Shell is used to make a secured connection to a remote system or device. ftp6 Enables or disables secure copy (SCP) and secure FTP (SFTP) at the same time on the switch. OmniSwitch 6250 CLI Reference Guide November 2009 page 7-49...
Print local working directory. ls [path] Display remote directory listing. mkdir path Create remote directory. put local-path [remote- Upload file. path] Display remote working directory. exit Quit the sftp mode. OmniSwitch 6250 CLI Reference Guide November 2009 page 7-51...
Page 264
Related Commands Starts an FTP session. Invokes Secure Shell on the switch. Secure Shell is used to make a secured connection to a remote system or device. MIB Objects SystemServices systemServicesArg1 systemServicesAction page 7-52 OmniSwitch 6250 CLI Reference Guide November 2009...
Creates a symbolic link (symlink) to the remote file. symlink oldpath newpath Creates a symbolic link (symlink) to the remote file. lmkdir path Create local directory. lpwd Print local working directory. ls [path] Display remote directory listing. OmniSwitch 6250 CLI Reference Guide November 2009 page 7-53...
Page 266
Related Commands ftp6 Starts an FTP6 session. ssh6 Invokes Secure Shellv6 on the switch. Secure Shellv6 is used to make a secured connection to an SSHv6 server. MIB Objects SystemServices systemServicesArg1 systemServicesAction page 7-54 OmniSwitch 6250 CLI Reference Guide November 2009...
A TFTP server has no provisions for user authentication. • Only one active TFTP client session is allowed at a time. • When downloading a file to the switch, the file size must not exceed the available flash space. OmniSwitch 6250 CLI Reference Guide November 2009 page 7-55...
Page 268
-> tftp 10.211.17.1 get source-file boot.cfg destination-file /flash/working/ boot.cfg ascii -> tftp 10.211.17.1 get source-file boot.cfg ascii Release History Release 6.6.1; command was introduced. Related Commands MIB Objects systemServices systemServicesArg1 systemServicesArg2 systemServicesArg3 systemServicesArg4 systemServicesArg5 systemServicesAction page 7-56 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 269
-> rz Upload directory: /flash rz ready to receive file, please start upload (or send 5 CTRL-X's to abort). Release History Release 6.6.1; command was introduced. Related Commands MIB Objects systemServices systemServicesAction OmniSwitch 6250 CLI Reference Guide November 2009 page 7-57...
MIB information for the Web Management commands is as follows: Filename: AlcatelInd1WebMgt.mib Module: alcatelIND1WebMgtMIB A summary of the available commands is listed here: http server http ssl http port https port debug http sessiondb show http OmniSwitch 6250 CLI Reference Guide November 2009 page 8-1...
-> no https ssl Release History Release 6.6.1; command was introduced. Related Commands http server Enables/disables web management on the switch. show http Displays web management configuration information. MIB Objects alaIND1WebMgtConfigMIBGroup alaInd1WebMgtSsl OmniSwitch 6250 CLI Reference Guide November 2009 page 8-3...
-> http port default Release History Release 6.6.1; command was introduced. Related Commands http server Enables/disables web management on the switch. show http Displays web management configuration information. MIB Objects alaIND1WebMgtConfigMIBGroup alaIND1WebMgtHttpPort page 8-4 OmniSwitch 6250 CLI Reference Guide November 2009...
-> https port default Release History Release 6.6.1; command was introduced. Related Commands http server Enables/disables web management on the switch. show http Displays web management configuration information. MIB Objects alaIND1WebMgtConfigMIBGroup alaIND1WebMgtHttpsPort OmniSwitch 6250 CLI Reference Guide November 2009 page 8-5...
User-configured inactivity timer, in minutes. Status Session status. If the user has successfully logged in, the status is “Authenticated.” URL Name&StatMsg Current page being viewed by the user. Release History Release 6.6.1; command was introduced. page 8-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 277
Web Management Commands Related Commands http server Enables/disables web management on the switch. http ssl Enables/disables SSL on the switch. show http Displays web management configuration information. MIB Objects OmniSwitch 6250 CLI Reference Guide November 2009 page 8-7...
Web Management Http Port The port configured for the HTTP connection. Web Management Https Port The port configured for a secure HTTP connection (SSL enabled). Release History Release 6.6.1; command was introduced. page 8-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 279
Web Management Commands Related Commands http server Enables/disables web management on the switch. http ssl Enables/disables SSL on the switch. http port https port MIB Objects alaIND1WebMgtConfigMIBGroup alaInd1WebMgtAdminStatus alaInd1WebMgtSsl alaInd1WebMgtHttpPort alaInd1WebMgtHttpsPort OmniSwitch 6250 CLI Reference Guide November 2009 page 8-9...
Page 280
Web Management Commands page 8-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Module: Alcatel-IND1ConfigMgr.mib A summary of the available commands is listed here: configuration apply configuration error-file limit show configuration status configuration cancel configuration syntax check configuration snapshot show configuration snapshot write terminal OmniSwitch 6250 CLI Reference Guide November 2009 page 9-1...
To schedule a timer session in which a file is applied after a specific amount of time (i.e., a countdown) has passed, enter in followed by the number of hours and minutes. • Verbose mode is not supported for timer sessions. page 9-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 283
Release 6.6.1; command was introduced. Related Commands configuration syntax check Performs a syntax and authorization check of all CLI commands contained in a configuration file. MIB Objects alcatelIND1ConfigMgrMIBObjects configFileName configFileMode configFileAction configTimerFileName configTimerFileTime OmniSwitch 6250 CLI Reference Guide November 2009 page 9-3...
If you want to save an error file, you may change the file name so that it does not have the .err extension, or you can move it from the /flash directory. Examples -> configuration error-file limit 2 -> configuration error-file limit 1 Release History Release 6.6.1; command was introduced. page 9-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 285
Applies a configuration file to the switch. Also used for scheduling a timer session for a configuration file. configuration cancel Cancels a pending timer session for a configuration file. MIB Objects alcatelIND1ConfigMgrMIBObjects configErrorFileMaximum OmniSwitch 6250 CLI Reference Guide November 2009 page 9-5...
• To synchronize the running and saved configuration, use the write memory command. Examples -> show configuration status Release History Release 6.6.1; command was introduced. page 9-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 287
Specifies the maximum number of configuration error files allowed in the switch’s /flash directory. write memory Copies the running configuration (RAM) to the working directory. MIB Objects configTimerFileGroup configTimerFileStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 9-7...
Applies a configuration file to the switch. Also used for scheduling a timer session for a configuration file. show configuration status Displays whether there is a pending timer session scheduled for a configu- ration file. MIB Objects configTimerFileGroup configTimerClear page 9-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Note. When the configuration syntax check command is entered, one or more dots “.” is displayed in the command output. This indicates command progress; each dot represents 256 text lines in the configura- tion file processed by the syntax check mechanism. OmniSwitch 6250 CLI Reference Guide November 2009 page 9-9...
Page 290
Applies a configuration file to the switch. Also used for scheduling a timer session for a configuration file. show configuration status Displays whether there is a pending timer session scheduled for a configuration file. MIB Objects configFileGroup configErrorFileName configErrorFileMaximum configFileMode configFileStatus page 9-10 OmniSwitch 6250 CLI Reference Guide November 2009...
For example, the first default file name to be generated is asc.1.snap, the second default file name to be generated is named asc.2.snap, etc. By default, all snapshot files are placed in the root /flash directory. Platforms Supported OmniSwitch 6250 OmniSwitch 6250 CLI Reference Guide November 2009 page 9-11...
To show a list of features on the switch, use the show configuration snapshot ? syntax. • Configurations are listed below the name of each feature. • Features with no current configuration show only the name of the feature. OmniSwitch 6250 CLI Reference Guide November 2009 page 9-13...
Page 294
"local" user "public" read All write All no auth authkey 391b0e74dbd13973d703cceaa4a8e30 Release History Release 6.6.1; command was introduced. Related Commands write terminal Displays the switch’s current running configuration for all features. page 9-14 OmniSwitch 6250 CLI Reference Guide November 2009...
-> write terminal Release History Release 6.6.1; command was introduced. Related Commands show configuration snapshot Displays the switch’s current running configuration for all features or for the specified feature(s). MIB Objects configManager mib_configSnapshotAllSelect page 9-16 OmniSwitch 6250 CLI Reference Guide November 2009...
Filename: IETFsnmpCommunity.MIB Module: IETF SNMP-COMMUNITY.MIB MIB information for Trap Manager commands is a follows: Filename AlcatelIND1TrapMgr.MIB Module: ALCATEL-IND1-TRAP-MGR.MIB MIB information for SNMP Agent commands is a follows: Filename: AlcatelIND1SNMPAgent.MIB Module: ALCATEL-IND1-SNMP-AGENT.MIB OmniSwitch 6250 CLI Reference Guide November 2009 page 10-1...
Page 298
10-2 OmniSwitch 6250 CLI Reference Guide November 2009...
When modifying an SNMP station, you must specify an IP address plus at least one additional parameter. For example, the syntax snmp station 1.2.3.4 is not a valid command entry; however, snmp station 1.2.3.4 v2 is a valid command entry. OmniSwitch 6250 CLI Reference Guide November 2009 page 10-3...
Page 300
Release 6.6.1; command was introduced. Related Commands show snmp station Displays the current SNMP station information. MIB Objects trapStationTable trapStationIP trapStationPort trapStationUser trapStationProtocol trapStationRowStatus alaTrapInetStationTable alaTrapInetStationIPType alaTrapInetStationIP alaTrapInetStationPort alaTrapInetStationRowStatus alaTrapInetStationProtocol alaTrapInetStationUser page 10-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Status The Enabled/Disabled status of the SNMP management station. Protocol The version of SNMP set for this management station. User The user account name. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 10-5...
Page 302
Related Commands snmp station Adds a new SNMP station; modifies or deletes an existing SNMP station. MIB Objects trapStationTable trapStationIP trapStationPort trapStationUser trapStationProtocol trapStationRowStatus alaTrapInetStationTable alaTrapInetStationIPType alaTrapInetStationIP alaTrapInetStationPort alaTrapInetStationRowStatus alaTrapInetStationProtocol alaTrapInetStationUser page 10-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Privileges attached to the community string are the ones inherited from the user account name that created it. Examples -> snmp community map community1 user testname1 -> snmp community map community1 enable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 10-7...
Page 304
SNMP Commands Related Commands snmp community map mode Enables the local community strings database. MIB Objects SNMPCommunityTable snmpCommunityIndex snmpCommunitySecurityName snmpCommunityStatus page 10-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands snmp community map Configures and enables a community string on the switch and maps it to an existing user account name. MIB Objects SNMPCommunityTable snmpCommunityIndex snmpCommunitySecurityName snmpCommunityStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 10-9...
The user account name. Release History Release 6.6.1; command was introduced. Related Commands snmp community map Configures and enables a community string on the switch and maps it to an existing user account name. page 10-10 OmniSwitch 6250 CLI Reference Guide November 2009...
OmniSwitch 6250 CLI Reference Guide November 2009 page 10-11...
Page 308
-> snmp security privacy set -> snmp security trap only Release History Release 6.6.1; command was introduced. Related Commands show snmp security Displays the current SNMP security status. MIB Objects SNMPAgtConfig SnmpAgtSecurityLevel page 10-12 OmniSwitch 6250 CLI Reference Guide November 2009...
-> show snmp security snmp security = privacy set -> show snmp security snmp security = privacy all -> show snmp security snmp security = trap only Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 10-13...
Page 310
SNMP Commands Related Commands snmp security Configures the SNMP security settings. page 10-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 312
Name of the MIB object listed as an SNMP statistic. = (integer) The number of times the MIB object has been reported to the SNMP management station since the last reset. Release History Release 6.6.1; command was introduced. Related Commands page 10-16 OmniSwitch 6250 CLI Reference Guide November 2009...
Name of the MIB table. Family Command family to which this MIB table belongs. Release History Release 6.6.1; command was introduced. Related Commands show snmp trap filter Displays the SNMP trap filter information. OmniSwitch 6250 CLI Reference Guide November 2009 page 10-17...
Release 6.6.1; command was introduced. Related Commands show snmp trap config Displays the SNMP trap information. Information includes trap ID num- bers and corresponding trap names and families. MIB Objects trapFilterTable trapAbsorption page 10-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Release History Release 6.6.1; command was introduced. Related Commands show snmp trap config Displays the SNMP trap information, including the current status for trap absorption and WebView forwarding. MIB Objects trapFilterTable trapToWebView OmniSwitch 6250 CLI Reference Guide November 2009 page 10-19...
• If the specified sequence number is greater than the latest sequence number, no traps are replayed.. Examples -> snmp trap replay 172.12.2.100 -> snmp trap replay 300::1 page 10-20 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 317
Release 6.6.1; command was introduced. Related Commands show snmp station Displays the current SNMP station status. show snmp trap replay Displays the SNMP trap replay information. MIB Objects trapStationTable trapStation Replay AlaTrapInetStationEntry alaTrapInetStationReplay alaTrapInetStationNextSeq OmniSwitch 6250 CLI Reference Guide November 2009 page 10-21...
0300:0000:0000:0000:0211:d8ff:fe47:470c output definitions IPAddress IP address of the SNMP station manager that replayed the trap. Oldest Replay Number Number of the oldest replayed trap. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 10-25...
Page 322
SNMP Commands Related Commands snmp trap replay Replays stored traps from the switch to a specified SNMP station. MIB Objects trapStationTable snmpStation Replay AlaTrapInetStationEntry alaTrapInetStationReplay alaTrapInetStationNextSeq page 10-26 OmniSwitch 6250 CLI Reference Guide November 2009...
Related Commands snmp trap filter Enables or disables SNMP trap filtering. show snmp trap config Displays the SNMP trap information, including trap ID numbers, trap names, command families, and absorption rate. OmniSwitch 6250 CLI Reference Guide November 2009 page 10-27...
Identification number for the trap. Trap Name Name of the trap. Family Family to which the trap belongs. Absorption Time needed for the trap to process. Release History Release 6.6.1; command was introduced. page 10-30 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 327
Displays SNMP MIB information. snmp trap absorption Enables or disables the trap absorption function. snmp trap to webview Enables or disables the forwarding of SNMP traps to WebView. MIB Objects trapConfigTable trapConfigEntry OmniSwitch 6250 CLI Reference Guide November 2009 page 10-31...
MIB information for the DNS commands is as follows: Filename: AlcatelIND1System.mib Module: ALCATEL-IND1-SYSTEM.MIB A summary of the available commands is listed here. ip domain-lookup ip name-server ipv6 name-server ip domain-name show dns OmniSwitch 6250 CLI Reference Guide November 2009 page 11-1...
Specifies the IPv6 addresses of up to three IPv6 DNS servers to query on a host lookup. ip domain-name Sets or deletes the default domain name for DNS lookups. show dns Displays the current DNS resolver configuration and status. MIB Objects systemDNS systemDNSEnableDnsResolver page 11-2 OmniSwitch 6250 CLI Reference Guide November 2009...
You can configure up to three IPv4 DNS servers and three IPv6 DNS servers in a switch. Examples -> ip name-server 189.202.191.14 189.202.191.15 188.255.19.1 -> ip name-server 10.255.11.66 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 11-3...
Page 332
Enables or disables the DNS resolver. ip domain-name Sets or deletes the default domain name for DNS lookups. show dns Displays the current DNS resolver configuration and status. MIB Objects systemDNS systemDNSNsAddr1 systemDNSNsAddr2 systemDNSNsAddr3 page 11-4 OmniSwitch 6250 CLI Reference Guide November 2009...
You can configure up to three IPv6 DNS servers and three IPv4 DNS servers in a switch. Examples -> ipv6 name-server fec0::2d0:d3:f3fc -> ipv6 name-server fe2d::2c f302::3de1:1 f1bc::202:fd40:f3 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 11-5...
Page 334
Enables or disables the DNS resolver. ip domain-name Sets or deletes the default domain name for DNS lookups. show dns Displays the current DNS resolver configuration and status. MIB Objects systemDNS systemDNSNsIPv6Addr1 systemDNSNsIPv6Addr2 systemDNSNsIPv6Addr3 page 11-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Specifies the IPv6 addresses of up to three IPv6 DNS servers to query on a host lookup. show dns Displays the current DNS resolver configuration and status. MIB Objects systemDNS systemDNSDomainName OmniSwitch 6250 CLI Reference Guide November 2009 page 11-7...
IPv6 nameServer(s) Indicates the IPv6 address(es) of the IPv6 DNS server(s). These addresses are set using the ipv6 name-server command. Release History Release 6.6.1; command was introduced. page 11-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 337
Specify the IPv6 addresses of up to three IPv6 DNS servers to query on a host lookup. ip domain-name Sets or deletes the default domain name for DNS lookups. MIB Objects systemDNS systemDNSEnableDnsResolver systemDNSDomainName systemDNSNsAddr1 systemDNSNsAddr2 systemDNSNsAddr3 systemDNSNsIPv6Addr1 systemDNSNsIPv6Addr2 systemDNSNsIPv6Addr3 OmniSwitch 6250 CLI Reference Guide November 2009 page 11-9...
Page 338
DNS Commands page 11-10 OmniSwitch 6250 CLI Reference Guide November 2009...
The dynamic aggregation software is compatible only with the following IEEE standard: 802.3ad — Aggregation of Multiple Link Segments MIB information for the link aggregation commands is as follows: Filename: AlcatelIND1LAG.MIB Module: ALCATEL-IND1-LAG-MIB OmniSwitch 6250 CLI Reference Guide November 2009 page 12-1...
Page 340
Static and dynamic show linkagg show linkagg port page 12-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Use the lacp linkagg size command to create a dynamic aggregation (i.e., LACP) group. See page 12-9 for more information about this command. Examples -> static linkagg 3 size 8 -> static linkagg 4 size 2 admin state disable -> no static linkagg 3 OmniSwitch 6250 CLI Reference Guide November 2009 page 12-3...
Page 342
Link Aggregation Commands Release History Release 6.6.1; command was introduced. Related Commands show linkagg Displays information about static and dynamic (LACP) link aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggSize alclnkaggAggLacpType alclnkaggAggName alclnkaggAggAdminState page 12-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands static linkagg size Creates a static aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggName OmniSwitch 6250 CLI Reference Guide November 2009 page 12-5...
Release 6.6.1; command was introduced. Related Commands static linkagg size Creates a static aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggAdminState page 12-6 OmniSwitch 6250 CLI Reference Guide November 2009...
The ethernet, fastethernet, and gigaethernet keywords do not modify a port’s configuration. See Chapter 20, “Ethernet Port Commands,” for information on CLI commands to configure Ethernet ports. Examples -> static agg 2/1 agg num 4 -> static agg no 2/1 OmniSwitch 6250 CLI Reference Guide November 2009 page 12-7...
Page 346
Release History Release 6.6.1; command was introduced. Related Commands static linkagg size Creates a static aggregate group. show linkagg port Displays information about link aggregation ports. MIB Objects alclnkaggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortLacpType alclnkaggAggPortSelectedAggNumber page 12-8 OmniSwitch 6250 CLI Reference Guide November 2009...
The priority of the remote system to which the aggregation group is attached. Possible values are 0–65535. partner_admin_key The administrative key for the aggregation group’s remote partner. Possible values are 0–65535. OmniSwitch 6250 CLI Reference Guide November 2009 page 12-9...
Page 348
Release 6.6.1; command was introduced. Related Commands show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggSize alclnkaggAggLacpType alclnkaggAggName alclnkaggAggAdminState alclnkaggAggActorAdminKey alclnkaggAggActorSystemPriority alclnkaggAggActorSystemID alclnkaggAggPartnerSystemID alclnkaggAggPartnerSystemPriority alclnkaggAggPartnerAdminKey page 12-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggName OmniSwitch 6250 CLI Reference Guide November 2009 page 12-11...
When the administrative state is set to disable, the operation of a dynamic aggregation (LACP) group cannot be performed. Examples -> lacp linkagg 2 admin state disable Release History Release 6.6.1; command was introduced. page 12-12 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 351
Creates a dynamic aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. show linkagg port Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggAdminState OmniSwitch 6250 CLI Reference Guide November 2009 page 12-13...
Release 6.6.1; command was introduced. Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggActorAdminKey page 12-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggActorSystemPriority OmniSwitch 6250 CLI Reference Guide November 2009 page 12-15...
Release 6.6.1; command was introduced. Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggActorSystemID page 12-16 OmniSwitch 6250 CLI Reference Guide November 2009...
The partner_system_id and the partner_system_priority specify the remote system’s priority. Examples -> lacp linkagg 2 partner system id 00:20:da4:32:81 -> lacp linkagg 2 no partner system id Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 12-17...
Page 356
Link Aggregation Commands Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggPartnerSystemID page 12-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggPartnerSystemPriority OmniSwitch 6250 CLI Reference Guide November 2009 page 12-19...
Release 6.6.1; command was introduced. Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg Displays information about static and dynamic (LACP) aggregate groups. MIB Objects alclnkaggAggTable alclnkaggAggNumber alclnkaggAggPartnerAdminKey page 12-20 OmniSwitch 6250 CLI Reference Guide November 2009...
Possible values are 0–255. partner admin state See the lacp agg partner admin state command on page 12-30. actor_port_priority The priority of the actor port. Possible values are 0–255. OmniSwitch 6250 CLI Reference Guide November 2009 page 12-21...
Page 360
Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregates. MIB Objects alclnkaggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggActorAdminKey alclnkaggAggPortLacpType alclnkaggAggPortActorAdminState alclnkaggAggPortActorSystemID page 12-22 OmniSwitch 6250 CLI Reference Guide November 2009...
Specifying that this keyword has no effect because the system always determines its value. When this bit (bit 6) is set by the system, it indi- page 12-24 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 363
Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregate groups. MIB Objects alclnkaggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortActorAdminState OmniSwitch 6250 CLI Reference Guide November 2009 page 12-25...
CLI commands to configure Ethernet ports. Examples -> lacp 3/1 actor system id 00:20:da:06:ba:d3 -> lacp 3/1 no actor system id Release History Release 6.6.1; command was introduced. page 12-26 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 365
Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregate groups. MIB Objects alclnkaggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortActorSystemID OmniSwitch 6250 CLI Reference Guide November 2009 page 12-27...
CLI commands to configure Ethernet ports. Examples -> lacp agg ethernet 3/2 actor system priority 65 -> lacp agg ethernet 3/2 no actor system priority Release History Release 6.6.1; command was introduced. page 12-28 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 367
Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregates. MIB Objects AlcLnkAggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortActorSystemPriority OmniSwitch 6250 CLI Reference Guide November 2009 page 12-29...
Specifying that this keyword has no effect because the system always determines its value. When this bit (bit 6) is set by the system, it indi- page 12-30 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 369
Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregate groups. MIB Objects alclnkaggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortPartnerAdminState OmniSwitch 6250 CLI Reference Guide November 2009 page 12-31...
Chapter 20, “Ethernet Port Commands,” for information on CLI commands to configure Ethernet ports. Examples -> lacp agg 3/1 partner admin system id 00:20:da:05:f6:23 Release History Release 6.6.1; command was introduced. page 12-32 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 371
Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregate groups. MIB Objects AlcLnkAggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortPartnerAdminSystemID OmniSwitch 6250 CLI Reference Guide November 2009 page 12-33...
CLI commands to configure Ethernet ports. Examples -> lacp agg 2/1 partner admin key 0 -> lacp agg 2/1 no partner admin key Release History Release 6.6.1; command was introduced. page 12-34 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 373
Displays detailed information about ports associated with a particular aggregate group or all aggregate groups. show linkagg port Displays information about slots and ports associated with all aggregate groups. MIB Objects AlcLnkAggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortPartnerAdminKey OmniSwitch 6250 CLI Reference Guide November 2009 page 12-35...
CLI commands to configure Ethernet ports. Examples -> lacp agg 2/1 partner admin system priority 65 -> lacp agg 2/1 no partner admin system priority Release History Release 6.6.1; command was introduced. page 12-36 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 375
Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregate groups. MIB Objects AlcLnkAggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortAdminSystemPriority OmniSwitch 6250 CLI Reference Guide November 2009 page 12-37...
CLI commands to configure Ethernet ports. Examples -> lacp agg 2/1 actor port priority 100 -> lacp agg 2/1 no actor port priority Release History Release 6.6.1; command was introduced. page 12-38 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 377
Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregate groups. MIB Objects AlcLnkAggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortActorPortPriority OmniSwitch 6250 CLI Reference Guide November 2009 page 12-39...
CLI commands to configure Ethernet ports. Examples -> lacp agg 2/1 partner admin port 255 -> lacp agg 2/1 no partner admin port Release History Release 6.6.1; command was introduced. page 12-40 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 379
Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregate groups. MIB Objects AlcLnkAggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortPartnerAdminPort OmniSwitch 6250 CLI Reference Guide November 2009 page 12-41...
CLI commands to configure Ethernet ports. Examples -> lacp agg 2/1 partner admin port priority 100 -> lacp agg 2/1 no partner admin port priority Release History Release 6.6.1; command was introduced. page 12-42 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 381
Related Commands lacp linkagg size Creates a dynamic aggregate group. show linkagg port Displays information about ports associated with a particular aggregate group or all aggregate groups. MIB Objects AlcLnkAggAggPortTable alclnkaggAggPortGlobalPortNumber alclnkaggAggPortPartnerAdminPortPriority OmniSwitch 6250 CLI Reference Guide November 2009 page 12-43...
Aggregate The type of aggregate group, which can be Static or Dynamic. SNMP Id The SNMP ID associated with the aggregate group. Size The number of links in this aggregate group. page 12-44 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 383
Number of Reserved Ports The total number of ports reserved for use in link aggregation by this static aggregate group. (Note: This field is not relevant for static aggre- gate groups.) OmniSwitch 6250 CLI Reference Guide November 2009 page 12-45...
Page 384
The total number of ports reserved for use in link aggregation by this dynamic aggregate group. Number of Attached Ports The number of ports actually attached to this dynamic aggregate group. page 12-46 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 385
The operational key of the remote system to which the dynamic aggre- gation group is attached. Release History Release 6.6.1; command was introduced. Related Commands static linkagg size Creates a static aggregate group. lacp linkagg size Creates a dynamic aggregate group. OmniSwitch 6250 CLI Reference Guide November 2009 page 12-47...
The SNMP ID associated with the aggregate group. Status The current status of the port, which can be CONFIGURED, PENDING, SELECTED, or RESERVED. The number of the aggregate groups associated with this port. OmniSwitch 6250 CLI Reference Guide November 2009 page 12-49...
Page 388
The port number of the first port to join this static aggregate group. If the first port to join the aggregate is no longer part of the aggregate group, the switch automatically assigns another port in the aggregate group to be the primary port. page 12-50 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 389
If the first port to join the aggregate is no longer part of the aggregate group, the switch automatically assigns another port in the aggregate group to be the primary port. OmniSwitch 6250 CLI Reference Guide November 2009 page 12-51...
Page 390
You can modify this parameter with the lacp agg partner admin port priority command (see page 12-42). Partner Oper Port Priority The priority value assigned to the this port by the partner. page 12-52 OmniSwitch 6250 CLI Reference Guide November 2009...
13 802.1AB Commands Alcatel-Lucent’s 802.1AB is an IEEE standard for exchanging information with neighboring devices and maintaining a database of the information. The information is exchanged using the LLDPDU (Link Layer Discovery Protocol Data Unit) in TLV (Time, Length, Value) format. This chapter details configuring and monitoring 802.1AB on a switch.
Sets the transmit hold multiplier value, which is used to calculate the Time To Live TLV. show lldp local -system Displays local system information. MIB Objects lldpConfiguration lldpMessageTxInterval page 13-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Release History Release 6.6.1; command was introduced. Related Commands lldp transmit interval Sets the transmit time interval for LLDPDUs. show lldp local -system Displays local system information. MIB Objects lldpConfiguration lldpMessageTxHoldMultiplier OmniSwitch 6250 CLI Reference Guide November 2009 page 13-3...
Release History Release 6.6.1; command was introduced. Related Commands lldp transmit interval Sets the transmit time interval for LLDPDUs. show lldp local -system Displays local system information. MIB Objects lldpConfiguration lldpTxDelay page 13-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands lldp transmit delay Sets the minimum time interval between successive LLDPDUs trans- mitted. show lldp local -system Displays local system information. MIB Objects lldpConfiguration lldpReinitDelay OmniSwitch 6250 CLI Reference Guide November 2009 page 13-5...
Release 6.6.1; command was introduced. Related Commands lldp notification Specifies the switch to control per port notification status about the remote device change. show lldp local -system Displays local system information. MIB Objects lldpConfiguration lldpNotificationInterval page 13-6 OmniSwitch 6250 CLI Reference Guide November 2009...
If this command is applied to a slot or chassis, then the existing configuration related to this command will be lost. Examples -> lldp 1/2 lldpdu tx-and-rx -> lldp chassis lldpdu disable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 13-7...
Page 400
LLDPDUs for a particular chassis, a slot, or a port. lldp notification Specifies the switch to control per port notification status about the remote device change. MIB Objects lldpPortConfigTable lldpPortConfigPortNum lldpPortConfigAdminStatus page 13-8 OmniSwitch 6250 CLI Reference Guide November 2009...
If this command is applied to a slot or chassis, then the existing configuration related to this command will be lost. Examples -> lldp 1/2 notification enable -> lldp 1 notification disable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 13-9...
Page 402
MIB change is generated. lldp lldpdu Specifies the switch to control the transmission and the reception of LLDPDUs for a particular chassis, a slot, or a port. MIB Objects lldpPortConfigTable lldpPortConfigPortNum lldpPortConfigNotificationEnable page 13-10 OmniSwitch 6250 CLI Reference Guide November 2009...
If this command is applied to a slot or chassis, then the existing configuration related to this command will be lost. Examples -> lldp 1/2 tlv management port-description enable -> lldp 2 tlv management management-address enable -> lldp 3 tlv management system-name disable OmniSwitch 6250 CLI Reference Guide November 2009 page 13-11...
Page 404
Displays local system information. show lldp local -port Displays per port information. show lldp remote-system Displays per local port and information of remote system. MIB Objects lldpPortConfigTable lldpLocPortPortNum lldpPortConfigTLVsTxEnable lldpConfigManAddrTable lldpConfigManAddrPortsTxEnable page 13-12 OmniSwitch 6250 CLI Reference Guide November 2009...
If one TLV is included then the other TLV is automatically included when you use this command. Examples -> lldp 5/1 tlv dot1 port-vlan enable -> lldp 3 tlv dot1 vlan-name enable -> lldp 3 tlv dot1 vlan-name disable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 13-13...
Page 406
Specifies the switch to control per port management TLVs to be incor- porated in the LLDPDUs. show lldp statistics Displays per port statistics. show lldp local -port Displays per port information. MIB Objects lldpPortConfigTable lldpPortConfigPortNum lldpXdot1ConfigPortVlanTable lldpXdot1ConfigPortVlanTxEnable lldpXdot1ConfigVlanNameTable lldpXdot1ConfigVlanNameTxEnable page 13-14 OmniSwitch 6250 CLI Reference Guide November 2009...
If this command is applied to a slot or chassis, then the existing configuration related to this command will be lost. Examples -> lldp 2/4 tlv dot3 mac-phy enable -> lldp 2 tlv dot3 mac-phy disable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 13-15...
Page 408
Specifies the switch to control per port 802.1 TLVs to be incorporated in the LLDPDUs. show lldp statistics Displays per port statistics. MIB Objects lldpPortConfigTable lldpPortConfigPortNum lldpXdot3PortConfigTable lldpXdot3PortConfigTLVsTxEnable page 13-16 OmniSwitch 6250 CLI Reference Guide November 2009...
Examples -> lldp 4/4 tlv med power enable -> lldp 4/3 tlv med capability enable -> lldp 4 tlv med power disable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 13-17...
Page 410
Specifies the switch to control per port 802.1 TLVs to be incorporated in the LLDPDUs. lldp tlv dot3 Specifies the switch to control per port 802.3 TLVs to be incorporated in the LLDPDUs. MIB Objects lldpPortConfigTable lldpPortConfigPortNum lldpXMedPortConfigTable lldpXMedPortConfigTLVsTxEnable page 13-18 OmniSwitch 6250 CLI Reference Guide November 2009...
The total number of LLDPDUs dropped because of insufficient resources. Remote Systems MIB Age The total number of complete age-outs in the tables associated with the Outs remote system. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 13-19...
Page 412
Sets the time interval that must elapse before a notification about the local system MIB change is generated. MIB Objects lldpStatistics lldpStatsRemTablesLastChangeTime lldpStatsRemTablesInserts lldpStatsRemTablesDeletes lldpStatsRemTablesDrops lldpStatsRemTablesAgeouts page 13-20 OmniSwitch 6250 CLI Reference Guide November 2009...
The total number of unrecognized LLDP TLVs on the port. TLV Discards The total number of LLDP TLVs discarded on the port. Device Ageouts The total number of complete age-outs on the port. OmniSwitch 6250 CLI Reference Guide November 2009 page 13-21...
Page 414
Specifies the switch to control per port management TLVs to be incor- porated in the LLDPDUs. MIB Objects lldpStatsTxPortTable lldpStatsTxPortNum lldpStatsTxPortFramesTotal lldpStatsRxPortTable lldpStatsRxPortNum lldpStatsRxPortFramesDiscardedTotal lldpStatsRxPortFramesErrors lldpStatsRxPortFramesTotal lldpStatsRxPortTLVsDiscardedTotal lldpStatsRxPortTLVsUnrecognizedTotal lldpStatsRxPortAgeoutsTotal page 13-22 OmniSwitch 6250 CLI Reference Guide November 2009...
Capabilites Supported The capabilities of the system. Capabilites Enabled The enabled capabilities of the system. LLDPDU Transmit Interval The LLDPDU transmit interval. TTL Hold Multiplier The hold multiplier used to calculate TTL. OmniSwitch 6250 CLI Reference Guide November 2009 page 13-23...
Page 416
Sets the minimum time interval between successive LLDPDUs trans- mitted. MIB Objects lldpLocalSystemData lldpLocChassisIdSubtype lldpLocChassisId lldpLocSysName lldpLocSysDesc lldpLocSysCapSupported lldpLocSysEnabled lldpPortConfigTable lldpMessageTxInterval lldpMessageTXHoldMultiplier lldpTxDelay lldpReinitDelay lldpNotificationInterval lldpLocManAddrTable lldpLocManAddrSubtype lldpLocManAddr page 13-24 OmniSwitch 6250 CLI Reference Guide November 2009...
Local Slot 1/Port 8 LLDP Info: Port ID = 1008 (Locally assigned), Port Description = Alcatel 1/8 6.3.1.636.R01, Local Slot 1/Port 9 LLDP Info: Port ID = 1009 (Locally assigned), Port Description = Alcatel 1/9 6.3.1.636.R01, OmniSwitch 6250 CLI Reference Guide November 2009 page 13-25...
Page 418
= Alcatel 2/1 6.3.1.636.R01, Local Slot 2/Port 2 LLDP Info: Port ID = 2002 (Locally assigned), Port Description = Alcatel 2/2 6.3.1.636.R01, Local Slot 2/Port 3 LLDP Info: Port ID = 2003 (Locally assigned), page 13-26 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 419
= 2021 (Locally assigned), Port Description = Alcatel 2/21 6.3.1.636.R01, Local Slot 2/Port 22 LLDP Info: Port ID = 2022 (Locally assigned), Port Description = Alcatel 2/22 6.3.1.636.R01, Local Slot 2/Port 23 LLDP Info: OmniSwitch 6250 CLI Reference Guide November 2009 page 13-27...
Page 420
Local Slot 2/Port 41 LLDP Info: Port ID = 2041 (Locally assigned), Port Description = Alcatel 2/41 6.3.1.636.R01, Local Slot 2/Port 42 LLDP Info: Port ID = 2042 (Locally assigned), Port Description = Alcatel 2/42 6.3.1.636.R01, page 13-28 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 421
Specifies the switch to control per port management TLVs to be incor- porated in the LLDPDUs. lldp tlv dot1 Specifies the switch to control per port 802.1 TLVs to be incorporated in the LLDPDUs. MIB Objects lldpLocPortTable lldpLocPortNum lldpLocPortIdsubtype lldpLocPortId lldpLocPortDesc OmniSwitch 6250 CLI Reference Guide November 2009 page 13-29...
Specifies the switch to control per port management TLVs to be incor- porated in the LLDPDUs. show lldp local -system Displays local system information. MIB Objects lldpLocManAddrTable lldpLocManAddrLen lldpLocManAddrIfSubtype lldpLocManAddrIfId page 13-30 OmniSwitch 6250 CLI Reference Guide November 2009...
Port ID Subtype = 7 (Locally assigned), Port ID = 2047, Port Description = (null), System Name = (null), System Description = (null), Capabilites Supported = none supported, Capabilites Enabled = none enabled, OmniSwitch 6250 CLI Reference Guide November 2009 page 13-31...
Page 424
-port Displays per port information. show lldp local -system Displays local system information. MIB Objects lldpRemTable lldpRemLocalPortNum lldpRemChassisIdSubtype lldpRemChassisId lldpRemPortIdSubtype lldpRemPortId lldpRemPortDesc lldpRemSysName lldpRemSysDesc lldpRemSysCapSupported lldpRemSysCapEnabled lldpRemManAddrIfSubtype lldpRemManAddrIfId page 13-32 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 425
14 Interswitch Protocol Commands Alcatel-Lucent Interswitch Protocols (AIP) are used to discover and advertise adjacent switch information. Only one protocol is supported: • Alcatel-Lucent Mapping Adjacency Protocol (AMAP), used to discover the topology of OmniSwitches. This chapter includes descriptions of AMAP commands.
Interswitch Protocol Commands amap Enables or disables the Alcatel-Lucent Mapping Adjacency Protocol (AMAP) on the switch. AMAP discovers adjacent switches by sending and responding to Hello update packets on active Spanning Tree ports. amap {enable | disable} Syntax Definitions enable Enables AMAP.
The discovery transmission time value is also used by ports in the common transmission state to deter- mine how long to wait for Hello packets (see page 14-5). Examples -> amap discovery 1200 -> amap discovery time 600 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 14-3...
Page 428
Sets the common transmission time interval used by active Span- ning Tree ports in the common transmission state. show amap Displays adjacent switches and associated MAC addresses, ports, VLANs, and IP addresses. MIB Objects aipAMAPdisctime page 14-4 OmniSwitch 6250 CLI Reference Guide November 2009...
A port reverts to the discovery transmission state if a Hello response is not received after the discovery time interval (see page 14-3) has expired. Examples -> amap common 1200 -> amap common time 600 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 14-5...
Page 430
Sets the discovery transmission time interval used by the active Spanning Tree ports in the discovery transmission state. show amap Displays adjacent switches and associated MAC addresses, ports, VLANs, and IP addresses. MIB Objects aipAMAPcommontime page 14-6 OmniSwitch 6250 CLI Reference Guide November 2009...
AMAP Common Phase Time- The number of seconds to wait between each Hello packet transmission out Interval (seconds) during the common phase. Use the amap common time command to change this value. OmniSwitch 6250 CLI Reference Guide November 2009 page 14-7...
Page 432
Sets the discovery transmission time interval used by active Span- ning Tree ports in the discovery transmission state. amap common time Sets the common transmission time interval used by the active Spanning Tree ports in the common transmission state. page 14-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 433
15 802.1Q Commands Alcatel-Lucent’s 802.1Q is an IEEE standard for sending frames through the network tagged with VLAN identification. This chapter details configuring and monitoring 802.1Q tagging on a single port in a switch or an aggregate of ports on a switch.
The port’s default VLAN can never be configured to accepted tagged frames. Examples -> vlan 2 802.1q 3/1 -> vlan 10 802.1q 100 -> vlan 5 802.1q 4/2 "802.1q tag 2" -> vlan 6 no 802.1q 3/1 page 15-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 435
Configures a port to accept only VLAN-tagged frames or all frames. show 802.1q Displays 802.1Q tagging status and configuration. MIB Objects QPORTVLANTABLE qPortVlanSlot qPortVlanPort qPortVLanStatus qPortVlanTagValue qPortVlanDescription qAggregateVlanTagValue qAggregateVlanAggregateId qAggregateVlanStatus qAggregateVlanDescription OmniSwitch 6250 CLI Reference Guide November 2009 page 15-3...
Frames that are not discarded by this ingress rule are classified and processed according to the ingress rules for this port. Examples -> vlan 802.1q 3/1 frame type all Release History Release 6.6.1; command was introduced. page 15-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 437
Related Commands vlan 802.1q Creates, modifies, or deletes 802.1Q tagging on a single port or an aggregate of ports. show 802.1q Displays 802.1Q tagging status and configuration. MIB Objects DOT1QPORTVLANTABLE dot1dBasePort dot1qPortAcceptableFrameTypes OmniSwitch 6250 CLI Reference Guide November 2009 page 15-5...
The acceptable frame type for this port, which can be Any Frame Type or Tagged Only Frame Type. Force Tag Internal This field displays if adding the default VLAN ID (VID) to tagged frames is turned on or off. page 15-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 439
Creates, modifies, or deletes 802.1Q tagging on a single port or an aggregate of ports. vlan 802.1q frame type Configures a port to accept only VLAN-tagged frames or all frames. MIB Objects QPORTVLANTABLE qPortVlanSlot qPortVlanPort qPortVLanStatus qPortVlanTagValue qPortVlanDescription qAggregateVlanTagValue qAggregateVlanAggregateId qAggregateVlanStatus qAggregateVlanDescription OmniSwitch 6250 CLI Reference Guide November 2009 page 15-7...
Based on the IEEE 802.1D standard, the Alcatel-Lucent STP implementation distributes the Spanning Tree load between the primary management module and the network interface modules. In the case of a stack of switches, the STP load is distributed between the primary management switch and other switches in the stack.
Page 442
1x1 forward delay show spantree cist show spantree msti show spantree 1x1 Implicit port commands bridge slot/port bridge slot/port priority bridge slot/port path cost bridge slot/port mode bridge slot/port connection show spantree ports page 16-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 443
RRSTP commands bridge rrstp bridge rrstp ring bridge rrstp ring vlan-tag bridge rrstp ring status show bridge rrstp configuration show bridge rrstp ring PVST+ commands bridge mode 1x1 pvst+ bridge port pvst+ OmniSwitch 6250 CLI Reference Guide November 2009 page 16-3...
Tree status for an individual VLAN (see Chapter 22, “VLAN Management Commands”). Note that active ports associated with such a VLAN are excluded from any Spanning Tree calculations and will remain in a forwarding state. page 16-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 445
Selects the Spanning Tree protocol for the specified instance. bridge bpdu-switching Enables the switching of Spanning Tree BPDU on a VLAN that has Spanning Tree disabled. show spantree Displays VLAN Spanning Tree parameter values. MIB Objects vStpTable vStpNumber vStpMode OmniSwitch 6250 CLI Reference Guide November 2009 page 16-5...
1x1 Spanning Tree mode. • Deleting all existing MSTIs is required before changing the protocol from MSTP to STP or RSTP. page 16-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 447
Explicit command for changing the Spanning Tree protocol for the flat mode instance. bridge 1x1 protocol Explicit command for changing the Spanning Tree protocol for a VLAN instance. MIB Objects vStpInsTable vStpInsNumber vStpInsMode vStpInsProtocolSpecification OmniSwitch 6250 CLI Reference Guide November 2009 page 16-7...
Note that when a configuration snapshot is taken of the switch, all Spanning Tree commands are saved in their explicit format. Examples -> bridge cist protocol rstp -> bridge cist protocol mstp -> bridge cist protocol stp page 16-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 449
Implicit command for changing the Spanning Tree protocol for the flat mode instance or for a 1x1 mode VLAN instance. bridge 1x1 protocol Explicit command for changing the Spanning Tree protocol for a VLAN instance. MIB Objects vStpInsTable vStpInsNumber vStpInsProtocolSpecification OmniSwitch 6250 CLI Reference Guide November 2009 page 16-9...
Implicit command for changing the Spanning Tree protocol for the flat mode instance or for a 1x1 mode VLAN instance. bridge cist protocol Explicit command for changing the Spanning Tree protocol for the flat mode instance. page 16-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Spanning Tree mode and using MSTP. Examples -> bridge mst region name SalesRegion -> bridge mst region name “Alcatel-Lucent Marketing” -> bridge mst region no name Release History Release 6.6.1; command was introduced.
Page 453
Defines a MSTI number that identifies an association between a range of VLANs and a Spanning Tree instance. bridge msti vlan Defines an association between a range of VLANs and a single MSTI. MIB Objects vStpMstRegionTable vStpMstRegionNumber vStpMstRegionConfigName OmniSwitch 6250 CLI Reference Guide November 2009 page 16-13...
Defines a MSTI number that identifies an association between a range of VLANs and a Spanning Tree instance. bridge msti vlan Defines an association between a range of VLANs and a single MSTI. MIB Objects vStpMstRegionTable vStpMstRegionNumber vStpMstRegionConfigRevisionLevel page 16-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Spanning Tree mode and using the MSTP. Examples -> bridge mst region max hops 40 -> bridge mst region max hops 10 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-15...
Page 456
Defines a MSTI number that identifies an association between a range of VLANs and a Spanning Tree instance. bridge msti vlan Defines an association between a range of VLANs and a single MSTI. MIB Objects vStpMstRegionTable vStpMstRegionNumber vStpMstRegionMaxHops page 16-16 OmniSwitch 6250 CLI Reference Guide November 2009...
Examples -> bridge msti 10 -> bridge msti 20 name BldgOneST10 -> bridge msti 20 no name -> bridge no msti 10 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-17...
Page 458
Defines the maximum number of hops for the MST region. bridge msti vlan Defines an association between a range of VLANs and a single MSTI. MIB Objects vStpMstInstanceTable vStpMstInstanceNumber vStpMstInstanceName vStpMstInstanceVlanBitmapAddition vStpMstInstanceVlanBitmapDeletion vStpMstInstanceVlanBitmapState page 16-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 460
Defines the maximum number of hops for the MST region. bridge msti Defines a MSTI number that identifies an association between a range of VLANs and a Spanning Tree instance. MIB Objects vStpMstVlanAssignmentTable vStpMstVlanAssignmentVlanNumber vStpMstVlanAssignmentMstiNumber page 16-20 OmniSwitch 6250 CLI Reference Guide November 2009...
• Note that when the protocol is changed to/from MSTP, the bridge priority for the flat mode CIST instance is reset to the default value. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-21...
Page 462
Explicit command for changing the Spanning Tree priority for a VLAN instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpInsNumber vStpInsMode vStpInsPriority vStpInsBridgeAddress page 16-22 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 464
1x1 protocol Explicit command for changing the Spanning Tree priority for a VLAN instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpInsNumber vStpInsPriority vStpInsBridgeAddress page 16-24 OmniSwitch 6250 CLI Reference Guide November 2009...
Note that when the protocol is changed to/from MSTP, the bridge priority for the flat mode CIST instance is reset to the default value. • In regards to the priority for an MSTI, only the four most significant bits are used. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-25...
Page 466
Explicit command for changing the Spanning Tree priority for a VLAN instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpInsMstiNumber vStpInsMode vStpInsPriority vStpInsBridgeAddress page 16-26 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 468
Explicit command for changing the Spanning Tree priority for an MSTP MSTI when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpIns1x1VlanNumber vStpInsMode vStpInsPriority vStpInsBridgeAddress page 16-28 OmniSwitch 6250 CLI Reference Guide November 2009...
Examples -> bridge mode flat -> bridge hello time 5 -> bridge mode 1x1 -> bridge 10 hello time 8 -> bridge hello time 5 OmniSwitch 6250 CLI Reference Guide November 2009 page 16-29...
Page 470
Explicit command for changing the Spanning Tree hello time value for a VLAN instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpInsNumber vStpInsMode vStpInsBridgeHelloTime page 16-30 OmniSwitch 6250 CLI Reference Guide November 2009...
-> bridge cist hello time 5 -> bridge cist hello time 10 -> bridge mode 1x1 -> bridge cist hello time 5 -> bridge cist hello time 10 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-31...
Page 472
Explicit command for changing the Spanning Tree hello time value for a VLAN instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpInsNumber vStpInsBridgeHelloTime page 16-32 OmniSwitch 6250 CLI Reference Guide November 2009...
-> bridge 1x1 10 hello time 10 -> bridge mode 1x1 -> bridge 1x1 255 hello time 5 -> bridge 1x1 455 hello time 10 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-33...
Page 474
Explicit command for changing the Spanning Tree hello time value for the CIST instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpIns1x1VlanNumber vStpInsMode vStpInsBridgeHelloTime page 16-34 OmniSwitch 6250 CLI Reference Guide November 2009...
Examples -> bridge mode flat -> bridge max age 40 -> bridge mode 1x1 -> bridge 255 max age 40 -> bridge max age 10 OmniSwitch 6250 CLI Reference Guide November 2009 page 16-35...
Page 476
Explicit command for changing the Spanning Tree max age time value for a VLAN instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpInsNumber vStpInsMode vStpInsBridgeMaxAge page 16-36 OmniSwitch 6250 CLI Reference Guide November 2009...
-> bridge cist max age 10 -> bridge cist max age 30 -> bridge mode 1x1 -> bridge cist max age 10 -> bridge cist max age 30 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-37...
Page 478
Explicit command for changing the Spanning Tree max age time value for a VLAN instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpInsNumber vStpInsBridgeMaxAge page 16-38 OmniSwitch 6250 CLI Reference Guide November 2009...
-> bridge 1x1 10 max age 40 -> bridge mode 1x1 -> bridge 1x1 255 max age 30 -> bridge 1x1 455 max age 10 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-39...
Page 480
Explicit command for changing the Spanning Tree max age time value for the CIST instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpIns1x1VlanNumber vStpInsMode vStpInsBridgeMaxAge page 16-40 OmniSwitch 6250 CLI Reference Guide November 2009...
CIST instance and is not a configurable parameter. Examples -> bridge mode flat -> bridge forward delay 30 -> bridge mode 1x1 -> bridge 255 forward delay 10 -> bridge forward delay 30 OmniSwitch 6250 CLI Reference Guide November 2009 page 16-41...
Page 482
VLAN instance when the switch is operating in either the flat or 1x1 mode. bridge rrstp ring vlan-tag Displays VLAN Spanning Tree parameter values. MIB Objects vStpInsTable vStpInsNumber vStpInsMode vStpInsBridgeForwardDelay page 16-42 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 484
Explicit command for changing the Spanning Tree forward delay time value for a VLAN instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpInsNumber vStpInsBridgeForwardDelay page 16-44 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 486
Explicit command for changing the Spanning Tree forward delay time value for the CIST instance when the switch is operating in either the flat or 1x1 mode. MIB Objects vStpInsTable vStpIns1x1VlanNumber vStpInsMode vStpInsBridgeForwardDelay page 16-46 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 488
Release 6.6.1; command was introduced. Related Commands vlan stp Enables or disables Spanning Tree instance for the specified VLAN. show spantree Displays VLAN Spanning Tree parameter values. MIB Objects vStpInsTable vStpInsBpduSwitching page 16-48 OmniSwitch 6250 CLI Reference Guide November 2009...
Related Commands bridge slot/port path cost Defines a Spanning Tree path cost for a port. bridge protocol Configures the protocol for the flat mode CIST instance or a 1x1 mode VLAN instance. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-49...
Page 490
Distributed Spanning Tree Commands MIB Objects vStpBridge vStpPathCostMode page 16-50 OmniSwitch 6250 CLI Reference Guide November 2009...
AVC does not have any effect on root bridges. Examples -> bridge auto-vlan-containment enable -> bridge auto-vlan-containment disable -> bridge msti 1 auto-vlan-containment disable -> bridge msti 1 auto-vlan containment enable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-51...
Page 492
Defines a Spanning Tree path cost for a port. show spantree msti ports Displays Spanning Tree port information for a flat mode Multiple Span- ning Tree Instance (MSTI). MIB Objects vStpInsTable vStpInsAutoVlanContainment vStpBridge vStpBridgeAutoVlanContainment page 16-52 OmniSwitch 6250 CLI Reference Guide November 2009...
Physical ports that are reserved for link aggregation do not participate in the Spanning Tree Algo- rithm. Instead, the algorithm is applied to the aggregate logical link (virtual port) that represents a collection of physical ports. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-53...
Page 494
1x1 or flat mode. vlan stp Enables or disables the Spanning Tree instance for a VLAN. bridge bpdu-switching Enables or disables BPDU switching for the specified VLAN. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortEnable page 16-54 OmniSwitch 6250 CLI Reference Guide November 2009...
Physical ports that are reserved for link aggregation do not participate in the Spanning Tree Algo- rithm. Instead, the algorithm is applied to the aggregate logical link (virtual port) that represents a collection of physical ports. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-55...
Page 496
1x1 or flat mode. vlan stp Enables or disables the Spanning Tree instance for a VLAN. bridge bpdu-switching Enables or disables BPDU switching for the specified VLAN. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortEnable page 16-56 OmniSwitch 6250 CLI Reference Guide November 2009...
Physical ports that are reserved for link aggregation do not participate in the Spanning Tree Algo- rithm. Instead, the algorithm is applied to the aggregate logical link (virtual port) that represents a collection of physical ports. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-57...
Page 498
1x1 or flat mode. vlan stp Enables or disables Spanning Tree instance for the specified VLAN. bridge bpdu-switching Enables or disables BPDU switching for the specified VLAN. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortEnable page 16-58 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 500
Explicit command for configuring the Spanning Tree priority for a port or an aggregate of ports for a VLAN instance when the switch is operat- ing in either the 1x1 or flat mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPriority page 16-60 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 502
Explicit command for configuring the Spanning Tree priority value for a port or an aggregate of ports for a VLAN instance when the switch is operating in either the 1x1 or flat mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPriority page 16-62 OmniSwitch 6250 CLI Reference Guide November 2009...
MSTI until the operating mode for the switch is changed to the flat mode. • Note that when a configuration snapshot is taken of the switch, all Spanning Tree commands are saved in their explicit format. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-63...
Page 504
Explicit command for configuring the Spanning Tree priority value for a port or an aggregate of ports for a VLAN instance when the switch is operating in either the 1x1 or flat mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPriority page 16-64 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 506
Explicit command for configuring the Spanning Tree priority value for a port or an aggregate of ports for an MSTI when the switch is operating in either the 1x1 or flat mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPriority page 16-66 OmniSwitch 6250 CLI Reference Guide November 2009...
• If a 32-bit path cost value is in use and the path_cost is set to zero, the following recommended default path cost values based on link speed are used. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-67...
Page 508
Aggregate Size Default Path Link Speed (number of links) Cost Value 10 MB 1,200,000 800,000 600,000 100 MB 120,000 80,000 60,000 1 GB 12,000 8,000 6,000 10 GB 1,200 page 16-68 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 510
Explicit command for configuring the Spanning Tree path cost for a port or an aggregate of ports for a VLAN instance when the switch is operat- ing in either the 1x1 or flat mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPathCost page 16-70 OmniSwitch 6250 CLI Reference Guide November 2009...
• If a 32-bit path cost value is in use and the path_cost is set to zero, the following recommended default path cost values based on link speed are used: OmniSwitch 6250 CLI Reference Guide November 2009 page 16-71...
Page 512
Aggregate Size Default Path Link Speed (number of links) Cost Value 10 MB 1,200,000 800,000 600,000 100 MB 120,000 80,000 60,000 1 GB 12,000 8,000 6,000 10 GB 1,200 page 16-72 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 514
Explicit command for configuring the Spanning Tree path cost value for a port or an aggregate of ports for a VLAN instance when the switch is operating in either the 1x1 or flat mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPathCost page 16-74 OmniSwitch 6250 CLI Reference Guide November 2009...
When MSTP is the active protocol on the switch, only a 32-bit path cost value is used. Using a 16-bit path cost value is not an option. • If zero is entered for the path_cost value, then the following recommended default path cost values based on link speed are used: OmniSwitch 6250 CLI Reference Guide November 2009 page 16-75...
Page 517
Explicit command for configuring the Spanning Tree path cost value for a port or an aggregate of ports for a VLAN instance when the switch is operating in either the 1x1 or flat mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPathCost OmniSwitch 6250 CLI Reference Guide November 2009 page 16-77...
If a 32-bit path cost value is in use and the path_cost is set to zero, the following IEEE 892.1S recom- mended default path cost values based on link speed are used: page 16-78 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 519
Aggregate Size Default Path Link Speed (number of links) Cost Value 10 MB 1,200,000 800,000 600,000 100 MB 120,000 80,000 60,000 1 GB 12,000 8,000 6,000 10 GB 1,200 OmniSwitch 6250 CLI Reference Guide November 2009 page 16-79...
Page 520
Explicit command for configuring the Spanning Tree path cost value for a port or an aggregate of ports for an MSTI when the switch is operating in either the 1x1 or flat Spanning Tree mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPathCost page 16-80 OmniSwitch 6250 CLI Reference Guide November 2009...
When port state is manually set to forwarding or blocking, the port remains in that state until it is changed using this command. • Ports manually configured to operate in a forwarding or blocking state do not participate in the Span- ning Tree Algorithm. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-81...
Page 522
Explicit command for configuring the Spanning Tree mode on a port or an aggregate of ports for a VLAN instance when the switch is operating in either the 1x1 or flat mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortManualMode page 16-82 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 524
Explicit command for configuring the Spanning Tree mode for a port or an aggregate of ports for the specified VLAN instance when the switch is operating in either the 1x1 or flat Spanning Tree mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortManualMode page 16-84 OmniSwitch 6250 CLI Reference Guide November 2009...
Ports manually configured to operate in a forwarding or blocking state do not participate in the Span- ning Tree algorithm. • When port state is manually set to forwarding or blocking, the port remains in that state until it is changed using this command. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-85...
Page 526
Explicit command for configuring the Spanning Tree mode for a port or an aggregate of ports for the CIST instance when the switch is operating in either the 1x1 or flat Spanning Tree mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortManualMode page 16-86 OmniSwitch 6250 CLI Reference Guide November 2009...
Otherwise, the port is considered connected to a no point to point LAN segment. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-87...
Page 528
Configures whether or not Spanning Tree automatically determines the operational edge status of a port or an aggregate of ports for the flat mode CIST instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortAdminConnectionType vStpInsPortOperConnectionType page 16-88 OmniSwitch 6250 CLI Reference Guide November 2009...
Rapid transition of an alternate port role to a root port role is not affected by the port connection type definition. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-89...
Page 530
Configures whether or not Spanning Tree automatically determines the operational edge status of a port or an aggregate of ports for the flat mode CIST instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortAdminConnectionType vStpInsPortOperConnectionType page 16-90 OmniSwitch 6250 CLI Reference Guide November 2009...
Rapid transition of an alternate port role to a root port role is not affected by the port connection type definition. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-91...
Page 532
Configures whether or not Spanning Tree automatically determines the operational edge status of a port or an aggregate of ports for the flat mode CIST instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortAdminConnectionType vStpInsPortOperConnectionType page 16-92 OmniSwitch 6250 CLI Reference Guide November 2009...
Rapid transition of an alternate port role to a root port role is not affected by the port connection type definition. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-93...
Page 534
Configures whether or not Spanning Tree determines the operational edge port status for a port or an aggregate of ports for the specified 1x1 mode VLAN instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortAdminEdge page 16-94 OmniSwitch 6250 CLI Reference Guide November 2009...
Rapid transition of a designated port to forwarding can only occur if the port’s connection type is defined as point to point or an edge port. Rapid transition of an alternate port role to a root port role is not affected by the port connection type definition. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-95...
Page 536
Configures whether or not Spanning Tree determines the operational edge port status for a port or an aggregate of ports for the specified 1x1 mode VLAN instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortAdminEdge page 16-96 OmniSwitch 6250 CLI Reference Guide November 2009...
MAC addresses on these ports if a topology change occurs as a result of another non-edge port going active. If an edge port receives a BPDU, it will operationally revert back to a no point to point connec- tion type. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-97...
Page 538
CIST instance. bridge 1x1 slot/port admin-edge Configures the administrative edge port status for a port or an aggre- gate of ports for a specific VLAN instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortAutoEdge page 16-98 OmniSwitch 6250 CLI Reference Guide November 2009...
MAC addresses on these ports if a topology change occurs as a result of another non-edge port going active. If an edge port receives a BPDU, it will operationally revert back to a no point to point connec- tion type. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-99...
Page 540
CIST instance. bridge 1x1 slot/port admin-edge Configures the administrative edge port status for a port or an aggre- gate of ports for a specific VLAN instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortAutoEdge page 16-100 OmniSwitch 6250 CLI Reference Guide November 2009...
Spanning Tree topology. • Note that when a configuration snapshot is taken of the switch, all Spanning Tree commands are saved in their explicit format. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-101...
Page 542
Selects the Spanning Tree operating mode (flat or 1x1) for the switch. bridge 1x1 slot/port restricted- Configures the restricted role status for a port or an aggregate of ports role for the 1x1 mode VLAN instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortRestrictedRole page 16-102 OmniSwitch 6250 CLI Reference Guide November 2009...
VLAN instance until the switch is running in the 1x1 Spanning Tree mode. • Note that when a configuration snapshot is taken of the switch, all Spanning Tree commands are saved in their explicit format. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-103...
Page 544
Selects the Spanning Tree operating mode (flat or 1x1) for the switch. bridge cist slot/port restricted- Configures the restricted role status for a port or an aggregate of ports role for the flat mode CIST instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortRestrictedRole page 16-104 OmniSwitch 6250 CLI Reference Guide November 2009...
CIST instance until the switch is running in the flat Spanning Tree mode. • Note that when a configuration snapshot is taken of the switch, all Spanning Tree commands are saved in their explicit format. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-105...
Page 546
Selects the Spanning Tree operating mode (flat or 1x1) for the switch. bridge 1x1 slot/port restricted- Configures the restricted TCN status for a port or an aggregate of ports for the specified 1x1 mode VLAN instance. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortRestrictedTcn page 16-106 OmniSwitch 6250 CLI Reference Guide November 2009...
VLAN instance until the switch is running in the 1x1 Spanning Tree mode. • Note that when a configuration snapshot is taken of the switch, all Spanning Tree commands are saved in their explicit format. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-107...
Page 548
Configures the restricted TCN status for a port or an aggregate of ports for the flat mode Common and Internal Spanning Tree (CIST). MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortRestrictedTcn page 16-108 OmniSwitch 6250 CLI Reference Guide November 2009...
Explicit command used to rate limit the transmission of BPDU for the specified VLAN instance when the switch is operating in either the 1x1 or flat Spanning Tree mode. MIB Objects vStpInsTable vStpInsBridgeTxHoldCount OmniSwitch 6250 CLI Reference Guide November 2009 page 16-109...
Explicit command used to rate limit the transmission of BPDU for the CIST instance when the switch is operating in either the 1x1 or flat Spanning Tree mode. MIB Objects vStpInsTable vStpInsBridgeTxHoldCount page 16-110 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands bridge rrstp ring Creates a RRSTP ring comprising of two ports. show bridge rrstp Displays the current RRSTP status for the switch. configuration MIB Objects vStpInfo VStpRrstpGlobalState OmniSwitch 6250 CLI Reference Guide November 2009 page 16-111...
Also RRSTP ring ports must be of same type i.e. either both ring ports should be NNI ports or both should be conventional ports. • RRSTP ring cannot be created on UNI ports. page 16-112 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 553
Enables RRSTP on a switch. show bridge rrstp ring Displays information for all the rings or a specific ring present in the system. MIB Objects vStpRrstpRingConfigTable vStpRrstpRingId vStpRrstpRingPort1 vStpRrstpRingPort2 vStpRrstpRingVlanTag vStpRrstpRingState vStpRrstpRingRowStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 16-113...
Related Commands bridge rrstp ring Creates a RRSTP ring comprising of two ports. show bridge rrstp ring Displays information for all the rings or a specific ring present in the system. page 16-114 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 555
Distributed Spanning Tree Commands MIB Objects vStpRrstpRingConfigTable vStpRrstpRingId vStpRrstpRingVlanTag OmniSwitch 6250 CLI Reference Guide November 2009 page 16-115...
Creates a RRSTP ring comprising of two ports. show bridge rrstp ring Displays information for all the rings or a specific ring present in the system. MIB Objects vStpRrstpRingConfigTable vStpRrstpRingId vStpRrstpRingState vStpRrstpRingRowStatus page 16-116 OmniSwitch 6250 CLI Reference Guide November 2009...
Examples -> bridge mode flat -> bridge protocol rstp -> show spantree Spanning Tree Path Cost Mode : AUTO Bridge STP Status Protocol Priority(Prio:SysID) ------+----------+--------+-------------------- RSTP 32768 (0x8000:0x0000 OmniSwitch 6250 CLI Reference Guide November 2009 page 16-117...
Page 558
The port that offers the next best (second lowest) cost path to the root bridge for this Spanning Tree instance. Tx Hold Count The count to limit the transmission of BPDU through the port. page 16-118 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 559
The Spanning Tree protocol applied to this instance. Configured through the bridge protocol command. Priority The Spanning Tree bridge priority for the instance. The lower the num- ber, the higher the priority. Configured through the bridge priority command. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-119...
Page 560
The Spanning Tree protocol applied to this instance (STP or RSTP). Configured through the bridge protocol command. Mode The Spanning Tree operating mode for the switch (PVST+, 1x1 or flat). Configured through bridge mode 1x1 pvst+ bridge mode command. page 16-120 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 561
The Max Age value for the root bridge. System Forward Delay The Forward Delay value for the root bridge. System Hello Time The Hello Time value for the root bridge. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-121...
Page 562
VLAN instance regardless of which mode (1x1 or flat) is active on the switch. MIB Objects vStpInsTable vStpInsNumber vStpInsProtocolSpecification vStpInsMode vStpInsPriority vStpInsBridgeAddress vStpInsDesignatedRoot vStpInsRootCost vStpInsRootPortNumber vStpInsNextBestRootCost vStpInsNextBestRootPortNumber vStpInsBridgeTxHoldCount vStpInsTopChanges vStpInsTimeSinceTopologyChange vStpInsMaxAge vStpInsForwardDelay vStpInsHelloTime page 16-122 OmniSwitch 6250 CLI Reference Guide November 2009...
Topology Changes Topology age 00:00:07, Current Parameters (seconds) Max Age Forward Delay Hello Time Parameters system uses when attempting to become root System Max Age System Forward Delay = System Hello Time OmniSwitch 6250 CLI Reference Guide November 2009 page 16-123...
Page 564
Spanning Tree instance (hh:mm:ss or dd days and hh:mm:ss). Max Age The amount of time (in seconds) that Spanning Tree Protocol informa- tion is retained before it is discarded. Configured through the bridge max age command. page 16-124 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 565
1x1 Explicit command for displaying the Spanning Tree bridge configu- ration for a VLAN instance regardless of which mode (1x1 or flat) is active on the switch. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-125...
MSTP 32771 (0x8000:0x0003) -> show spantree msti 0 Spanning Tree Parameters for Cist Spanning Tree Status : Protocol IEEE Multiple STP, mode FLAT (Single STP), Priority 32768 (0x8000), Bridge ID 8000-00:d0:95:6b:08:40, OmniSwitch 6250 CLI Reference Guide November 2009 page 16-127...
Page 568
-> show spantree msti Spanning Tree Path Cost Mode : AUTO ** Inactive flat mode instances: ** Msti STP Status Protocol Priority (Prio:SysID) -----+----------+--------+--------------------- MSTP 32768 (0x8000:0x0000) MSTP 32770 (0x8000:0x0002) MSTP 32771 (0x8000:0x0003) page 16-128 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 569
The port that offers the lowest cost path from this bridge to the root bridge for this Spanning Tree instance. Next Best Root Cost The cost of the next best root port for this Spanning Tree instance. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-129...
Page 570
1x1 Explicit command for displaying the Spanning Tree bridge configu- ration for a VLAN instance regardless of which mode (1x1 or flat) is active on the switch. page 16-130 OmniSwitch 6250 CLI Reference Guide November 2009...
Examples -> show spantree 1x1 Spanning Tree Path Cost Mode : AUTO Vlan STP Status Protocol Priority -----+----------+--------+-------------- 32768 (0x8000) 32768 (0x8000) 32768 (0x8000) 32768 (0x8000) 32768 (0x8000) 32768 (0x8000) page 16-132 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 573
Configured through the bridge priority command. Bridge ID The bridge identifier for this Spanning Tree instance. Consists of the bridge priority value (in hex) concatenated with the dedicated bridge MAC address. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-133...
Page 574
The Max Age value for the root bridge. System Forward Delay The Forward Delay value for the root bridge. System Forward Delay The Forward Delay value for the root bridge. Release History Release 6.6.1; command was introduced. page 16-134 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 575
MSTI when the switch is operating in the 1x1 or flat Spanning Tree mode. MIB Objects vStpInsTable vStpInsNumber vStpInsMode vStpInsProtocolSpecification vStpInsPriority vStpInsBridgeAddress vStpInsTimeSinceTopologyChange vStpInsTopChanges vStpInsDesignatedRoot vStpInsRootCost vStpInsRootPortNumber vStpInsNextBestRootCost vStpInsNextBestRootPortNumber vStpInsMaxAge vStpInsHelloTime vStpInsBridgeTxHoldCount vStpInsForwardDelay vStpInsBridgeMaxAge vStpInsBridgeHelloTime vStpInsBridgeForwardDelay vStpIns1x1VlanNumber OmniSwitch 6250 CLI Reference Guide November 2009 page 16-135...
The configured keyword is only available when an instance number is specified with this command. In addition, this keyword cannot be used in combination with either the forwarding or blocking keywords. page 16-136 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 577
(e.g., 0/31). Oper St The port operational state as defined by application of the Spanning Tree Protocol. Possible port operational states include: disabled, block- ing, learning, and forwarding. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-137...
Page 578
Adm St The Spanning Tree administrative status of the port: enabled or dis- abled. Configured through the bridge slot/port command to enable or disable Spanning Tree on a port. page 16-138 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 579
-> bridge protocol mstp -> show spantree ports Msti Port Oper Status Path Cost Role -----+-----+------------+---------+----- FORW 200000 ROOT 1/10 1/11 1/12 1/13 1/14 1/15 1/16 1/17 1/18 1/19 1/20 1/21 OmniSwitch 6250 CLI Reference Guide November 2009 page 16-139...
Page 580
Config- ured through the bridge slot/port path cost command. Role The role of the port for this Spanning Tree instance. Possible port roles are: root, designated, alternate, and backup. page 16-140 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 581
Path cost is a measure of the distance of the listed port from the root bridge in the number of hops. Config- ured through the bridge slot/port path cost command. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-141...
Page 582
The edge port administrative status: yes indicates that the port is an admin edge port; no indicates that the port is not an admin edge port. Configured through the bridge slot/port connection command. page 16-142 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 583
Tree mode. show spantree 1x1 ports Explicit command for displaying Spanning Tree port information for a VLAN instance when the switch is operating in the 1x1 or flat Spanning Tree mode. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-143...
Page 586
-> show spantree cist ports configured Spanning Tree Port Admin Configuration for Vlan 1 Port Man. Config Rstr Rstr Role/ OS8800 PVST+ Port Mode Cost Root Guard 10G Opt Cfg Stat -----+----+----+-----+-------+----+----+----+----+-----------+--------+-------- page 16-146 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 587
Indicates whether or not the PVST+ interoperability status is enabled (ENA) or disabled (DIS) for the port. Configured throught the bridge mode 1x1 pvst+ command. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-147...
Page 588
VLAN instance when the switch is operating in the 1x1 or flat Spanning Tree mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPriority vStpInsPortState vStpInsPortEnable vStpInsPortPathCost vStpInsPortDesignatedCost vStpInsPortDesignatedBridge vStpInsPortAdminEdge vStpInsPortAutoEdge vStpInsPortRestrictedRole vStpInsPortRestrictedTcn vStpInsPortManualMode vStpInsPortRole vStpInsPrimaryPortNumber vStpInsPortAdminConnectionType vStpInsPortOperConnectionType page 16-148 OmniSwitch 6250 CLI Reference Guide November 2009...
Note that MSTI 0 also represents the CIST instance that is always present on the switch. To view the CIST instance using this command, specify zero (0) for the msti_id number. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-149...
Page 591
Path cost is a measure of the distance of the listed port from the root bridge in the number of hops. Config- ured through the bridge msti slot/port path cost command. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-151...
Page 592
Adm St The Spanning Tree administrative status of the port: enabled or dis- abled. Configured through the bridge slot/port command to enable or disable Spanning Tree on a port. page 16-152 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 593
Spanning Tree mode. show spantree 1x1 ports Explicit command for displaying Spanning Tree port information for a VLAN when the switch is operating in the 1x1 or flat Span- ning Tree mode. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-153...
The configured keyword is only available when an instance number is specified with this command. In addition, this keyword cannot be used in combination with either the forwarding or blocking keywords. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-155...
Page 596
Spanning Tree Port Summary for Vl 11 Oper Path Desig Prim. Op Port Cost Cost Role Port Cnx Edg Desig Bridge ID -----+----+-------+-------+----+-----+---+---+--------------------- 1/36 DIS 1/36 NS EDG 0000-00:00:00:00:00:00 1/37 DIS 1/37 NO 0000-00:00:00:00:00:00 page 16-156 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 597
See the bridge slot/port connection command on page 16-87 for more information. Desig Bridge ID The bridge identifier for the designated bridge for this port’s segment. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-157...
Page 598
Adm St The Spanning Tree administrative status of the port: enabled or dis- abled. Configured through the bridge slot/port command to enable or disable Spanning Tree on a port. page 16-158 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 599
Indicates whether or not the PVST+ interoperability status is enabled (ENA) or disabled (DIS) for the port. Configured throught the bridge mode 1x1 pvst+ command. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-159...
Page 600
MSTI when the switch is operating in the 1x1 or flat Span- ning Tree mode. MIB Objects vStpInsPortTable vStpInsPortNumber vStpInsPortPriority vStpInsPortState vStpInsPortEnable vStpInsPortPathCost vStpInsPortDesignatedCost vStpInsPortDesignatedBridge vStpInsPortAdminConnectionType vStpInsPortOperConnectionType vStpInsPortAdminEdge vStpInsPortAutoEdge vStpInsPortRestrictedRole vStpInsPortRestrictedTcn vStpInsPortManualMode vStpInsPortRole vStpInsPrimaryPortNumber vStpInsPortAdminConnectionType vStpInsPortOperConnectionType page 16-160 OmniSwitch 6250 CLI Reference Guide November 2009...
An MST region identifier consisting of a 16 octet hex value (as per the IEEE 802.1Q 2005 standard) that represents all defined MSTIs and their associated VLAN ranges. Use the bridge msti bridge msti vlan commands to define VLAN to MSTI associations. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-161...
Page 602
Displays the range of VLANs associated to the CIST instance. show spantree map-msti Displays the MSTI that is associated to the specified VLAN MIB Objects vStpMstRegionTable vStpMstRegionNumber vStpMstRegionConfigDigest vStpMstRegionConfigName vStpMstRegionConfigRevisionLevel vStpMstRegionCistInstanceNumber vStpMstRegionMaxHops page 16-162 OmniSwitch 6250 CLI Reference Guide November 2009...
Name VLAN list : 10-11 Msti 2 Name VLAN list : 12-13 -> show spantree msti 2 vlan-map Spanning Tree Msti Vlan map ----------------------------- Msti 2 Name VLAN list : 12-13 OmniSwitch 6250 CLI Reference Guide November 2009 page 16-163...
Page 604
Displays the range of VLANs associated to the CIST instance. show spantree map-msti Displays the MSTI that is associated to the specified VLAN MIB Objects vStpMstInstanceTable vStpMstInstanceNumber vStpMstInstanceName vStpMstInstanceVlanBitmapState page 16-164 OmniSwitch 6250 CLI Reference Guide November 2009...
Displays the MST region information for the switch. show spantree msti vlan-map Displays the range of VLANs associated to the specified MSTI. show spantree map-msti Displays the MSTI that is associated to the specified VLAN OmniSwitch 6250 CLI Reference Guide November 2009 page 16-165...
Displays the range of VLANs associated to the specified MSTI. show spantree cist vlan-map Displays the range of VLANs associated to the CIST instance. MIB Objects vStpMstVlanAssignmentTable vStpMstVlanAssignmentVlanNumber vStpMstVlanAssignmentMstiNumber OmniSwitch 6250 CLI Reference Guide November 2009 page 16-167...
Related Commands bridge rrstp Enables RRSTP on a switch. show bridge rrstp ring Displays information for all the rings or a specific ring present in the system. MIB Objects vStpInfo VStpRrstpGlobalState page 16-170 OmniSwitch 6250 CLI Reference Guide November 2009...
The first port in the RRSTP ring. Ring-Port-2 The second port in the RRSTP ring. Ring Status The current state of the RRSTP ring (Enabled or Disabled). Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 16-171...
Page 612
Creates a RRSTP ring comprising of two ports. show bridge rrstp Displays the current RRSTP status for the switch. configuration MIB Objects vStpRrstpRingConfigTable vStpRrstpRingId vStpRrstpRingPort1 vStpRrstpRingPort2 vStpRrstpRingVlanTag vStpRrstpRingState vStpRrstpRingRowStatus page 16-172 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands bridge port pvst+ Configures the type of BPDU to be used on a port when PVST+ mode is enabled. MIB Objects vStpTable vStpMode vStpModePVST OmniSwitch 6250 CLI Reference Guide November 2009 page 16-173...
PVST+ BPDUs for tagged VLANs and IEEE BPDUs for default VLANs. Examples -> bridge port 1/3 pvst+ enable -> bridge port 2/2 pvst+ auto Release History Release 6.3.1; command was introduced. page 16-174 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 615
Distributed Spanning Tree Commands Related Commands bridge mode 1x1 pvst+ Enables or disables PVST+ mode on the switch. MIB Objects vStpPortConfigTable vStpPortConfigIfInedx vStpPortConfigPVST OmniSwitch 6250 CLI Reference Guide November 2009 page 16-175...
Page 616
Distributed Spanning Tree Commands page 16-176 OmniSwitch 6250 CLI Reference Guide November 2009...
MIB information for the Loopback Detection commands is as follows: Filename: alcatelIND1LBD.mib Module: ALCATEL-IND1-LBD-MIB A summary of available commands is listed here: loopback-detection loopback-detection port loopback-detection transmission-timer loopback-detection autorecovery-timer show loopback-detection show loopback-detection port show loopback-detection statistics port OmniSwitch 6250 CLI Reference Guide November 2009 page 17-1...
-> loopback-detection enable Release History Release 6.6.1; command was introduced. Related Commands loopback-detection port Enables or disables LBD on a specific port. show loopback-detection Displays LBD configuration information. MIB Objects alaLdbConfigTable alaLdbGLobalConfigStatus page 17-2 OmniSwitch 6250 CLI Reference Guide November 2009...
LBD is enabled globally. However, LBD functionality on a port is available only when LBD is enabled globally on the switch. Examples -> loopback-detection port 1/1 enable -> loopback-detection port 1/1-8 enable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 17-3...
Page 620
Loopback Detection Commands Related Commands loopback-detection Enables or disables LBD globally on the switch. show loopback-detection Displays LBD configuration information. MIB Objects alaLdbPortConfigTable alaLdbPortConfigEntry alaLdbPortConfigIndex alaLdbPortConfigLdbAdminStatus alaLdbPortConfigLdbOperStatus page 17-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Global LBD Auto-recovery Displays the autorecovery time period in seconds. It is the time period Timer that passes after which ports that were shut down through LBD are moved to normal state. OmniSwitch 6250 CLI Reference Guide November 2009 page 17-7...
Page 624
Release 6.6.1; command was introduced. Related Commands loopback-detection Enables or disables LBD globally on the switch. show loopback-detection port Displays LBD configuration information for all ports on the switch. MIB Objects alaLdbConfigTable alaLdbGLobalConfigStatus page 17-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Slot/Port The slot/port number LBD port. Admin State The administrative state of the port (Enabled or Disabled). Oper State The operational state of the port (Normal or Inactive). OmniSwitch 6250 CLI Reference Guide November 2009 page 17-9...
Page 626
Release 6.6.1; command was introduced. Related Commands loopback-detection Enables or disables LBD globally on the switch. show loopback-detection Displays LBD configuration information for the switch or for a specific port. MIB Objects alaLdbConfigTable alaLdbGLobalConfigStatus page 17-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands loopback-detection Enables or disables LBD globally on the switch. show loopback-detection Displays LBD configuration information for the switch or for a specific port. MIB Objects alaLdbConfigTable alaLdbGLobalConfigStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 17-11...
AlcatelInd1MacAddress.mib Module: ALCATEL-IND1-MAC-ADDRESS-MIB A summary of the available commands is listed here: mac-address-table mac-address-table static-multicast mac-address-table aging-time source-learning show mac-address-table show mac-address-table static-multicast show mac-address-table count show mac-address-table aging-time show source-learning OmniSwitch 6250 CLI Reference Guide November 2009 page 18-1...
ID to a VLAN before you configure the static MAC address. Only traffic from other ports associated with the same VLAN is directed to the static MAC address slot/port. page 18-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 631
Displays Source Learning MAC Address Table statistics. show mac-address-table aging- Displays the current aging time value for the Source Learning MAC time Address Table. MIB Objects slMacAddressTable slMacAddress slMacAddressManagement slMacAddressDisposition OmniSwitch 6250 CLI Reference Guide November 2009 page 18-3...
If a multicast prefix value is not present, then the address is treated as a regular MAC address and not allowed when using the mac-address-table static-multicast command. Also note that multicast addresses within the following ranges are not supported: 01:00:5E:00:00:00 to 01:00:5E:7F:FF:FF 01:80:C2:XX.XX.XX 33:33:XX:XX:XX:XX page 18-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 633
Displays a list of static multicast MAC addresses that are configured in multicast the Source Learning MAC Address Table. show mac-address-table count Displays Source Learning MAC Address Table statistics. MIB Objects slMacAddressTable slMacAddress slMacAddressManagement slMacAddressDisposition OmniSwitch 6250 CLI Reference Guide November 2009 page 18-5...
(ARP) table. This timeout value determines how long the switch retains dynamically learned ARP table entries. Examples -> mac-address-table aging-time 1200 -> no mac-address-table aging-time Release History Release 6.6.1; command was introduced. page 18-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 635
Displays Source Learning MAC Address Table statistics. show mac-address-table aging- Displays the current aging time value for the Source Learning MAC time Address Table. MIB Objects slMacAddressAgingTable slMacAgingValue OmniSwitch 6250 CLI Reference Guide November 2009 page 18-7...
MAC addresses from switch B or for a Transparent LAN Service, where the service provider does not require the MAC addresses of the customer network. Examples -> source-learning port 1/2 disable -> source-learning port 1/3-9 disable -> source-learning linkagg 10 disable page 18-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 637
Source Learning Commands Release History Release 6.6.1; command introduced. Related Commands show source-learning Displays Source Learning status of each port or linkagg ports on a switch. Related MIB Objects slMacAddressTable slMacLearningControlTable slMacLearningControlEntry slMacLearningControlStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 18-9...
MAC address. When the port link comes up, however, the MAC address is then considered valid and the asterisk no longer appears next to the address in the display. page 18-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 639
MAC address. If the interface is a link aggregate ID, zero is displayed as the slot number (e.g., 0/29). Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 18-11...
Page 640
Displays Source Learning MAC Address Table statistics. show mac-address-table aging- Displays the current aging time value for the Source Learning MAC time Address Table. MIB Objects slMacAddressTable slMacAddress slMacAddressManagement slMacAddressDisposition slMacAddressProtocol page 18-12 OmniSwitch 6250 CLI Reference Guide November 2009...
The asterisk indicates that MAC address is invalid. When the port link comes up, however, the MAC address is then considered valid and the asterisk no longer appears next to the address in the display. OmniSwitch 6250 CLI Reference Guide November 2009 page 18-13...
Page 642
ID, zero is displayed as the slot number (e.g., 0/29). Release History Release 6.6.1; command was introduced. Related Commands show mac-address-table Displays Source Learning MAC Address Table information. show mac-address-table count Displays Source Learning MAC Address Table statistics. page 18-14 OmniSwitch 6250 CLI Reference Guide November 2009...
-> show mac-address-table count 10-20 Mac Address Table count: Permanent Address Count DeleteOnReset Address Count DeleteOnTimeout Address Count Dynamic Learned Address Count = 28 Total MAC Address In Use = 28 page 18-16 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 645
Release 6.6.1; command was introduced. Related Commands show mac-address-table Displays Source Learning MAC Address Table information. show mac-address-table aging- Displays the current aging time value for the Source Learning MAC time Address Table. OmniSwitch 6250 CLI Reference Guide November 2009 page 18-17...
Example -> show source-learning port source-learning -----+------------- disabled enabled disabled -> show source-learning port 1/2 port source-learning -----+------------- disabled -> show source-learning linkagg 10 port source-learning -----+------------- 0/10 disabled OmniSwitch 6250 CLI Reference Guide November 2009 page 18-19...
Page 648
Configures the status of source MAC address learning on a single port, a range of ports or on a link aggregate of ports. Related MIB Objects slMacAddressTable slMacLearningControlTable slMacLearningControlEntry slMacLearningControlStatus page 18-20 OmniSwitch 6250 CLI Reference Guide November 2009...
A summary of the available commands is listed here: port-security port-security shutdown port-security maximum port-security max-filtering port-security convert-to-static port-security mac port-security mac-range port-security violation port-security release port-security learn-trap-threshold show port-security show port-security shutdown OmniSwitch 6250 CLI Reference Guide November 2009 page 19-1...
Disables LPS on the specified port(s). chassis disable Disables all LPS-eligible ports on the chassis. Defaults By default, LPS is disabled on all switch ports. parameter default enable | disable enable Platforms Supported OmniSwitch 6250 page 19-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 651
Configures the amount of time in minutes to allow source learning on all LPS ports. port-security violation Selects the method for handling traffic that does not comply with LPS restrictions for the specified port(s). MIB Objects learnedPortSecurityTable lpsAdminStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 19-3...
MAC addresses are converted to static MAC addresses. This stops the MAC addresses from aging out. • The conversion of dynamic MAC addresses to static ones does not apply to LPS mobile and authenti- cated ports. page 19-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 653
Specifies the maximum number of source MAC addresses that an LPS port(s) is allowed to learn. port-security violation Selects the method for handling traffic that does not comply with LPS restrictions for the specified port. MIB Objects learnedPortSecurityGlobalGroup lpsLearningWindowTime lpsLearningWindowTimeWithStaticConversion OmniSwitch 6250 CLI Reference Guide November 2009 page 19-5...
LPS time limit has not expired. Examples -> port-security 2/14 maximum 25 -> port-security 4/10-15 maximum 100 Release History Release 6.6.1; command was introduced. page 19-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 655
MAC addresses on LPS ports. port-security violation Selects the method for handling traffic that does not comply with LPS restrictions for the specified port. MIB Objects learnedPortSecurityTable lpsMaxMacNum OmniSwitch 6250 CLI Reference Guide November 2009 page 19-7...
Specifies the maximum number of source MAC addresses that an LPS port(s) is allowed to learn. port-security violation Selects the method for handling traffic that does not comply with LPS restrictions for the specified port. MIB Objects learnedPortSecurityTable lpsMaxFilteredMacNum page 19-8 OmniSwitch 6250 CLI Reference Guide November 2009...
The number of converted static MAC addresses cannot exceed the maximum number of MAC addresses allowed on the port(s). Examples -> port-security 4/8 convert-to-static Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 19-9...
Page 658
Enables or disables Learned Port Security (LPS) on the switch port(s). port-security maximum Specifies the maximum number of source MAC addresses that an LPS port(s) is allowed to learn. MIB Objects learnedPortSecurityGlobalGroup lpsConvertToStatic page 19-10 OmniSwitch 6250 CLI Reference Guide November 2009...
MAC addresses and the maximum number of addresses allowed is set to 10, then only 7 addi- tional MAC addresses are allowed on that port. Examples -> port-security 4/20 mac 00:20:95:00:fa:5c vlan 2 -> port-security 2/11 no mac 00:20:95:00:fa:5c Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 19-11...
Page 660
Specifies the maximum number of source MAC addresses that an LPS port(s) is allowed to learn. port-security violation Selects the method for handling traffic that does not comply with LPS restrictions for the specified port. MIB Objects learnedPortSecurityL2MacAddressTable lpsL2MacAddress lpsL2VlanId lpsL2MacAddressRowStatus page 19-12 OmniSwitch 6250 CLI Reference Guide November 2009...
For example, if a port has 3 configured autho- rized MAC addresses and the maximum number of addresses allowed is set to 10, then only 7 addi- tional MAC addresses are allowed on that port. OmniSwitch 6250 CLI Reference Guide November 2009 page 19-13...
Page 662
Specifies the maximum number of source MAC addresses that an LPS port(s) is allowed to learn. port-security violation Selects the method for handling traffic that does not comply with LPS restrictions for the specified port. MIB Objects learnedPortSecurityTable lpsLoMacRange lpsHiMacRange lpsRowStatus page 19-14 OmniSwitch 6250 CLI Reference Guide November 2009...
(restrict) due to a security violation, use the port-security release command to restore the port to normal operation. Examples -> port-security 2/14 violation restrict -> port-security 4/10-15 violation shutdown Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 19-15...
Page 664
Configures the amount of time in minutes to allow source learning on all LPS ports. Also, enables or disables the conversion of dynamic MAC addresses to static MAC addresses on LPS ports. MIB Objects learnedPortSecurityTable lpsViolationOption page 19-16 OmniSwitch 6250 CLI Reference Guide November 2009...
LPS ports. Also, enables or disables the conversion of dynamic MAC addresses to static MAC addresses on LPS ports. port-security maximum Specifies the maximum number of source MAC addresses that an LPS port(s) is allowed to learn. OmniSwitch 6250 CLI Reference Guide November 2009 page 19-17...
Page 666
Learned Port Security Commands MIB Objects learnedPortSecurityTable lpsRelease page 19-18 OmniSwitch 6250 CLI Reference Guide November 2009...
If the configuration is not saved before the next reboot, all dynamic MAC addresses are cleared from the LPS table. • The MAC Type field is blank if an authorized MAC address range is configured for the LPS port. page 19-20 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 669
MAC address for the port. Dynamic MAC addresses become configured MAC address entries after a configura- tion save and switch reboot. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 19-21...
Page 670
Learned Port Security Commands Related Commands show port-security shutdown Displays the amount of time during which source learning can occur on all LPS ports. MIB Objects learnedPortSecurityTable lpsMaxMacNum lpsMaxFilteredMacNum lpsLoMacRange lpsHiMacRange lpsViolationOption lpsOperStatus lpsRelease page 19-22 OmniSwitch 6250 CLI Reference Guide November 2009...
(enabled or disabled). Configured through the port-security shutdown command. Remaining Learning Window The remaining amount of time during which the LPS port can learn MAC addresses. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 19-23...
Page 672
Learned Port Security Commands Related Commands port-security learn-trap- Displays Learned Port Security (LPS) configuration and table threshold entries. MIB Objects learnedPortSecurityGlobalGroup lpsConvertToStatic lpsLearningWindowTime lpsLearningWindowTimeWithStaticConversion page 19-24 OmniSwitch 6250 CLI Reference Guide November 2009...
Gathering basic line statistics for Ethernet ports and passing this information to the user interface and configuration manager. MIB information for the Ethernet Port commands is as follows: Filename: AlcatelIND1Port.mib Module: alcatelIND1PortMIB Filename: IETF_ETHERLIKE.mib Module: EtherLike-MIB OmniSwitch 6250 CLI Reference Guide November 2009 page 20-1...
Page 674
20-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Platforms Supported OmniSwitch 6250 Usage Guidelines Examples -> trap 3/1 port link enable -> trap 3 port link enable -> trap 3/1-6 port link enable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-3...
Page 676
Ethernet Port Commands Related Commands show interfaces status Displays interface line settings. MIB Objects esmConfigTable esmPortSlot esmPortIF page 20-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Configuration changes made with the interfaces speed command on combo ports configured as either forced copper or preferred copper will only be made on the copper RJ-45 ports and not to the SFP fiber port. See the interfaces hybrid speed command for more information. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-5...
Page 678
Release History Release 6.6.1; command was introduced. Related Commands interfaces duplex Configures duplex mode. interfaces autoneg Enables and disables auto negotiation. show interfaces status Displays interface line settings. MIB Objects esmConfTable esmPortCfgSpeed page 20-6 OmniSwitch 6250 CLI Reference Guide November 2009...
SFP fiber port. See the interfaces hybrid crossover command for more information. Examples -> interfaces 3 crossover mdi -> interfaces 3/1 crossover mdix -> interfaces 3/1-4 crossover auto Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-9...
Page 682
Configures interface speed. interfaces autoneg Enables and disables auto negotiation. show interfaces status Displays interface line settings. show interfaces capability Displays auto negotiation, speed, duplex, and crossover settings. MIB Objects esmConfTable esmPortCfgCrossover page 20-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Note that the operational settings, as shown in the following table, override the configured settings as long as autonegotiation and flow control are both enabled for the interface: OmniSwitch 6250 CLI Reference Guide November 2009 page 20-11...
Page 684
Release 6.6.1; command was introduced. Related Commands interfaces hybrid pause Configures flow control settings for combo ports. show interfaces pause Displays interface flow control settings. MIB Objects esmConfigTable esmPortCfgFlow dot3PauseTable dot3PauseAdminMode page 20-12 OmniSwitch 6250 CLI Reference Guide November 2009...
Configuration changes made with the interfaces duplex command on combo ports configured as either forced copper or preferred copper will only be made on the copper RJ-45 ports and not to the SFP fiber port. See the interfaces hybrid duplex command for more information. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-13...
Page 686
Configures interface line speed. Set to auto to set speed and duplex mode to auto-sensing. show interfaces status Displays interface line settings (e.g., speed, and mode). MIB Objects esmConfTable esmPortAutoDuplexMode page 20-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands show interfaces Displays general interface information (e.g., hardware, MAC address, input errors, and output errors). show interfaces port Displays port status (up or down). MIB Objects ifTable ifAdminStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 20-15...
Displays general interface information (e.g., hardware, MAC address, input errors, and output errors). show interfaces port Displays port status (up or down) and any aliases for a port. MIB Objects ifXTable ifAlias page 20-16 OmniSwitch 6250 CLI Reference Guide November 2009...
-> interfaces 3/1-4 ifg 10 Release History Release 6.6.1; command was introduced. Related Commands show interfaces ifg Displays the inter-frame gap value for one or more ports. MIB Objects esmConfTable esmPortCfgIfg OmniSwitch 6250 CLI Reference Guide November 2009 page 20-17...
“1” (one) will result in an error message. Examples -> interfaces 3/1 no l2 statistics -> interfaces 3 no l2 statistics -> interfaces 3/1-6 no l2 statistics Release History Release 6.6.1; command was introduced. page 20-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 691
Displays interface error frame information (e.g., CRC errors, transit errors, and receive errors). show interfaces collisions Displays interface collision information (e.g., number of collisions and number of retries). MIB Objects alcetherStatsTable alcetherClearStats OmniSwitch 6250 CLI Reference Guide November 2009 page 20-19...
-> interfaces 3/1-3 max frame 1518 Release History Release 6.6.1; command was introduced. Related Commands show interfaces Displays general interface information (e.g., hardware, MAC address, input errors, and output errors). MIB Objects esmConfTable esmPortCfgMaxFrameSize page 20-20 OmniSwitch 6250 CLI Reference Guide November 2009...
This does not prevent the normal flow of multicast traffic on the specified interface. Examples -> interfaces 3 flood multicast -> interfaces 1/24 flood multicast -> interfaces 1/23-24 flood multicast Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-21...
Page 694
Ethernet Port Commands Related Commands show interfaces flood rate Displays interface peak flood rate settings. interfaces flood rate Configures the peak flood rate for an interface. MIB Objects esmConfTable esmPortFloodMcastEnable page 20-22 OmniSwitch 6250 CLI Reference Guide November 2009...
OmniSwitch 6250 Usage Guidelines • Although you can configure a flood rate equal to the line speed you should not do so. Alcatel-Lucent recommends that you always configure the flood rate to be less than the line speed. • You can only configure one slot at a time. Repeat the command to configure additional slots.
Page 696
Release 6.6.1; command was introduced. Related Commands show interfaces flood rate Displays interface peak flood rate settings. interfaces flood multicast Enables/disables flood rate limiting for multicast traffic on an interface. MIB Objects esmConfTable esmPortMaxFloodRate page 20-24 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 699
Enables or disables flow (pause). show interfaces hybrid status Displays interface line settings for combo ports. show interfaces hybrid Displays auto negotiation, speed, duplex, and crossover settings for capability combo ports. MIB Objects esmHybridConfTable esmHybridPortCfgAutoNegotiation OmniSwitch 6250 CLI Reference Guide November 2009 page 20-27...
MIB object for the active configured media. Examples -> interfaces 1/25 hybrid copper crossover disable -> interfaces 1/25-26 hybrid copper crossover mdix -> interfaces hybrid copper crossover auto Release History Release 6.6.1; command was introduced. page 20-28 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 701
Enables or disables flow (pause) for combo ports. show interfaces hybrid status Displays interface line settings for combo ports. show interfaces hybrid Displays auto negotiation, speed, duplex, and crossover settings for capability combo ports. MIB Objects esmHybridConfTable esmHybridPortCfgCrossover OmniSwitch 6250 CLI Reference Guide November 2009 page 20-29...
Examples -> interfaces 1/25 hybrid copper duplex auto -> interfaces 1/25-26 hybrid copper duplex half -> interfaces 1 hybrid copper fiber full Release History Release 6.6.1; command was introduced. page 20-30 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 703
Configures interface line speed for combo ports. Set to auto to set speed and duplex mode to auto-sensing. show interfaces hybrid status Displays interface line settings (e.g., speed, mode) for combo ports. MIB Objects esmHybridConfTable esmHybridPortCfgDuplexMode OmniSwitch 6250 CLI Reference Guide November 2009 page 20-31...
The MIB table and MIB object listed in the “MIB Objects” section below apply to the inactive configured media only. See the “MIB Objects” section in the interfaces speed section for the MIB table and MIB object for the active configured media. page 20-32 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 705
Configures duplex mode for combo ports. interfaces hybrid autoneg Enables and disables auto negotiation for combo ports. show interfaces hybrid status Displays interface line settings for combo ports. MIB Objects esmHybridConfTable esmHybridPortCfgSpeed OmniSwitch 6250 CLI Reference Guide November 2009 page 20-33...
By default, flow control is disabled on all combo ports. Usage Guidelines • Flow control is only supported on interfaces configured to run in full-duplex mode; half-duplex mode is not supported. page 20-34 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 707
If autonegotiation is disabled, the configured flow control setting is applied to the local interface. Examples -> interfaces 1 hybrid fiber tx-and-rx -> interfaces 3/21-24 hybrid copper pause rx -> interfaces 3/21-24 hybrid copper disable Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-35...
Page 708
Ethernet Port Commands Related Commands interfaces pause Configures flow control settings for switch interfaces. show interfaces hybrid pause Displays flow control settings for combo ports. MIB Objects esmHybridConfigTable esmHybridPortCfgFlow dot3PauseTable dot3PauseAdminMode page 20-36 OmniSwitch 6250 CLI Reference Guide November 2009...
You can display a specific interface by entering the slot and port number (e.g., 3/1). • You can display a range of port numbers (e.g., 3/1-4). • You can display all interfaces in a slot by entering the slot number (e.g., 3). OmniSwitch 6250 CLI Reference Guide November 2009 page 20-37...
Page 710
Number of oversized frames received. Rx Lost Frames Number of Lost Frames received. Rx Error Frames Number of error frames received. Rx CRC Error Frames Number of CRC error frames received. page 20-38 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 711
Displays interface collision information (e.g., number of collisions and number of retries). show interfaces status Displays the interface line settings (e.g., speed and mode). show interfaces traffic Displays interface traffic statistics (input/output bytes and packets). OmniSwitch 6250 CLI Reference Guide November 2009 page 20-39...
In the row labeled CAP, the field displays the valid flow configurations for the port. In the row label DEF, the field displays the default flow settings for the port. The possible values are EN (enabled) or DIS (dis- abled). OmniSwitch 6250 CLI Reference Guide November 2009 page 20-41...
Page 714
Configures crossover port settings. interfaces speed Configures interface speed. interfaces duplex Configures duplex settings. show interfaces status Displays interface line settings. MIB Objects esmConfTable esmPortCfgAutoNegotiation esmPortCfgFlow esmPortCfgCrossover esmPortCfgSpeed esmPortAutoDuplexMode page 20-42 OmniSwitch 6250 CLI Reference Guide November 2009...
Interface slot and port number Active Interface status. Wait time Flow control wait time, in microseconds. Cfg-Flow Flow control status (Pause or Go). Cfg-Cross The user-configured cross-over setting (Auto, MDI, or MDIX). OmniSwitch 6250 CLI Reference Guide November 2009 page 20-43...
Page 716
Related Commands interfaces crossover Configures crossover settings. show interfaces hybrid flow control Displays interface flow control wait time settings for combo ports. MIB Objects esmConfTable esmPortSlot esmPortIF esmPortPauseSlotTime esmPortCfgCrossover dot3PauseTable dot3PauseSlotTime page 20-44 OmniSwitch 6250 CLI Reference Guide November 2009...
MDIX MDIX MDIX MDIX Auto Auto 65535 Auto 1/10 Auto 1/11 65535 Auto 1/12 Auto 1/13 Auto 1/14 Auto 1/15 Auto 1/16 Auto 1/17 Auto 1/18 Auto 1/19 Auto 1/20 Auto OmniSwitch 6250 CLI Reference Guide November 2009 page 20-45...
Page 718
Release History Release 6.6.1; command was introduced. Related Commands show interfaces hybrid pause Displays flow control pause settings for combo ports. MIB Objects esmConfTable esmPortSlot esmPortIF esmPortPauseSlotTime esmPortCfgCrossover esmPortActiveHybridType dot3PauseTable dot3PauseSlotTime page 20-46 OmniSwitch 6250 CLI Reference Guide November 2009...
For combo ports configured as either forced copper or preferred copper the accounting information for the copper RJ-45 ports and not the SFP fiber port will be displayed. See the show interfaces hybrid accounting command for more information. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-47...
Page 720
Release 6.6.1; command was introduced. Related Commands show interfaces Displays general interface information (e.g., hardware, MAC address, and input/output errors). show interfaces counters Displays interface counter information (e.g., unicast packets received/transmitted). page 20-48 OmniSwitch 6250 CLI Reference Guide November 2009...
For combo ports configured as either forced copper or preferred copper statistics for the copper RJ-45 ports and not the SFP fiber port will be displayed. See the show interfaces hybrid counters command for more information. page 20-50 OmniSwitch 6250 CLI Reference Guide November 2009...
For combo ports configured as either forced copper or preferred copper, statistics for the copper RJ-45 ports and not the SFP fiber port will be displayed. See the show interfaces hybrid counters errors command for more information. page 20-52 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 725
Release 6.6.1; command was introduced. Related Commands show interfaces counters Displays interface counters information (e.g., unicast, broadcast, and multi-cast packets received/transmitted). MIB Objects esmConfTable esmPortSlot esmPortIF ifTable ifInErrors ifOutErrors alcetherStatsTable alcetherStatsRxUndersizePkts dot3StatsTable dot3StatsAlignmentErrors dot3StatsFCSErrors dot3StatsFrameTooLong OmniSwitch 6250 CLI Reference Guide November 2009 page 20-53...
The hybrid mode for combo ports is not configurable; combo ports are set to preferred fiber by default. As a result, the Hybrid Mode field always displays preferred fiber (PF) for all combo ports. For non- combo ports, the Hybrid Type and Hybrid Mode fields display NA. page 20-56 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 729
The configured combo port type, which is PF (Preferred Fiber). Con- figuring the Hybrid Mode is not supported. Trap Link Up/Down Trap Link status (up/down). Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-57...
Page 730
RJ-45 port(s) when both ports are enabled and have a valid link. MIB Objects ifTable ifLinkUpDownTrapEnable esmConfTable esmPortSlot esmPortIF esmPortAutoSpeed esmPortAutoDuplexMode esmPortCfgSpeed esmPortCfgDuplexMode esmHybridConfTable esmPortCfgHybridMode esmPortCfgHybridType page 20-58 OmniSwitch 6250 CLI Reference Guide November 2009...
Slot/Port Admin Status Link Status Violations Alias ----------+--------------+------------+----------------+----------------------- 1/24 enable down NETSEC "" output definitions Slot/Port Interface slot and port number. Admin Status Port status (enable/disable). Link Status Operational status (enable/disable). OmniSwitch 6250 CLI Reference Guide November 2009 page 20-59...
Page 732
Clears all port violations set by various applications on the switch. interfaces alias Configures an alias for a port. MIB Objects esmConfTable esmPortSlot esmPortIF ifXTable ifAlias ifTable ifAdminStatus ifOperStatus page 20-60 OmniSwitch 6250 CLI Reference Guide November 2009...
You can display all interfaces in a slot by entering the slot number (e.g., 3). Examples -> show interfaces ifg Slot/Port ifg(Bytes) -----------+------------- 02/01 02/02 02/03 02/04 02/05 02/06 02/07 02/08 02/09 02/10 02/11 02/12 02/13 02/14 02/15 02/16 02/17 02/18 OmniSwitch 6250 CLI Reference Guide November 2009 page 20-61...
Page 734
Interface slot and port numbers. Inter-frame gap value (Gigabit Ethernet interface). Release History Release 6.6.1; command was introduced. Related Commands interfaces ifg Configures the inter-frame gap value. MIB Objects esmConfTable esmPortSlot esmPortIF esmPortCfgIFG page 20-62 OmniSwitch 6250 CLI Reference Guide November 2009...
Flood only 02/09 Flood only 02/10 Flood only 02/11 Flood only 02/12 Flood only 02/13 Flood only 02/14 Flood only 02/15 Flood only 02/16 Flood only 02/17 Flood only 02/18 Flood only OmniSwitch 6250 CLI Reference Guide November 2009 page 20-63...
Page 736
Configures the peak flood rate for an interface. interfaces flood multicast Enables/disables flood rate limiting for multicast traffic on an interface. MIB Objects esmConfTable esmPortSlot esmPortIF esmPortMaxFloodRate esmPortFloodMcastEnable page 20-64 OmniSwitch 6250 CLI Reference Guide November 2009...
You can display a specific interface by entering the slot and port number (e.g., 3/1). • You can display a range of port numbers (e.g., 3/1-4). • You can display all interfaces in a slot by entering the slot number (e.g., 3). OmniSwitch 6250 CLI Reference Guide November 2009 page 20-67...
Page 740
Rx Broadcast Frames Number of broadcast frames received. Rx M-cast Frames Number of multicast frames received. Rx Undersize Frames Number of undersized frames received. Rx Oversize Frames Number of r oversized frames received. page 20-68 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 741
Displays the interface line settings (e.g., speed, mode) for combo ports. show interfaces hybrid traffic Displays interface traffic statistics (input/output bytes and packets) for combo ports. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-69...
Interface status. Wait time Flow control wait time, in microseconds. Cfg-Flow Flow control status, which can be Pause or Go. Cfg-Cross The user-configured cross-over setting, which can be Auto, MDI, or MDIX. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-73...
Page 746
Related Commands interfaces hybrid crossover Configures crossover settings for combo ports. show interfaces flow control Displays interface flow control wait time settings. MIB Objects esmConfTable esmPortCfgSlot esmPortCfgIfIndex esmHybridConfTable esmHybridPortCfgFlow esmHybridPortPauseSlotTime esmHybridPortCfgCrossover page 20-74 OmniSwitch 6250 CLI Reference Guide November 2009...
-> show interfaces hybrid copper pause Slot/Port Active Wait time(usec) Cfg-Pause Cfg-Cross Hybrid Type -----------+--------+---------------+--------+-----------+----------- 1/25 Auto 1/26 Active 65535 Tx-N-Rx Auto output definitions Slot/Port Interface slot and port number Active Interface status. OmniSwitch 6250 CLI Reference Guide November 2009 page 20-75...
Page 748
Release History Release 6.6.1; command was introduced. Related Commands show interfaces pause Displays the interface flow control pause settings. MIB Objects esmConfTable esmPortCfgSlot esmPortCfgIF esmPortPauseSlotTime esmPortActiveHybridType esmHybridConfTable esmHybridPortCfgFlow esmHybridPortCfgCrossover dot3PauseTable dot3PauseSlotTime page 20-76 OmniSwitch 6250 CLI Reference Guide November 2009...
-> show interfaces 1/25 hybrid copper capability Slot/Port AutoNeg Flow Crossover Speed Duplex -----------+---------+--------+-----------+----------+---------- 1/25 CAP EN/DIS EN/DIS MDI/X/Auto 10/100/1G Full/Half 1/25 DEF Auto Auto Auto output definitions Slot The slot number. Port The port number OmniSwitch 6250 CLI Reference Guide November 2009 page 20-77...
Page 750
Configures duplex settings for combo ports. show interfaces hybrid status Displays interface line settings for combo ports. MIB Objects esmConfTable esmPortCfgSlot esmPortCfgIfIndex esmHybridConfTable esmHybridPortCfgAutoNegotiation esmHybridPortCfgFlow esmHybridPortCfgCrossover esmHybridPortCfgSpeed esmHybridPortCfgDuplex page 20-78 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 752
Displays general interface information (e.g., hardware, MAC address, input/output errors) for combo ports. show interfaces hybrid counters Displays interface counter information (e.g., unicast packets received/transmitted) for combo ports. page 20-80 OmniSwitch 6250 CLI Reference Guide November 2009...
OutPauseFrames= 786876, output definitions InOctets Number of octets received. OutOctets Number of octets transmitted. InUcastPkts Number of unicast packets received. OutUcastPkts Number of unicast packets transmitted. InMcastPkts Number of multicast packets received. page 20-82 OmniSwitch 6250 CLI Reference Guide November 2009...
= 867568, Oversize pkts = 5.98E8 output definitions Slot/Port Interface slot and port number. Alignments Errors Number of Alignments errors. FCS Errors Number of Frame Check Sequence errors. IfInErrors Number of received error frames. page 20-84 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 757
Release 6.6.1; command was introduced. Related Commands show interfaces hybrid counters Displays interface counters information (e.g., unicast, broadcast, multi-cast packets received/transmitted). MIB Objects esmConfTable esmPortCfgSlot esmPortCfgIfIndex ifTable ifInErrors ifOutErrors alcetherStatsTable alcetherStatsRxUndersizePkts dot3StatsTable dot3StatsAlignmentErrors dot3StatsFCSErrors dot3StatsFrameTooLong OmniSwitch 6250 CLI Reference Guide November 2009 page 20-85...
"" output definitions Slot/Port Interface slot and port number. Admin Status Port status (enable/disable). Link Status Operational status (enable/disable). Alias Interface alias. Release History Release 6.6.1; command was introduced. page 20-90 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 763
Ethernet Port Commands Related Commands interfaces admin Enables/disables an interface. interfaces alias Configures an alias for a port. MIB Objects esmConfTable esmPortCfgSlot esmPortCfgIfIndex ifXTable ifAlias ifTable ifAdminStatus ifOperStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 20-91...
Flood only 02/07 Flood only 02/08 Flood only 02/09 Flood only 02/10 Flood only 02/11 Flood only 02/12 Flood only 02/13 Flood only 02/14 Flood only 02/15 Flood only 02/16 Flood only page 20-92 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 765
Release 6.6.1; command was introduced. Related Commands interfaces flood rate Configures the peak flood rate for an interface. interfaces flood multicast Enables/disables flood multicasting on an interface. MIB Objects esmConfTable esmPortSlot esmPortIF esmPortMaxFloodRate esmPortFloodMcastEnable OmniSwitch 6250 CLI Reference Guide November 2009 page 20-93...
Rules are only assigned to existing VLANs. Use the vlan command to create a new VLAN. Examples -> vlan 10 dhcp mac 00:00:39:59:0a:0c -> vlan 20 dhcp mac 00:00:39:4f:f1:22 -> vlan 10 no dhcp mac 00:00:39:59:0a:0c page 21-2 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 771
DHCP frames that do not match other DHCP rules are tempo- rarily assigned to the VLAN. show vlan Displays existing VLANs. show vlan rules Displays rules defined for VLANs. MIB Objects vDhcpMacRuleTable vDhcpMacRuleAddr vDhcpMacRuleVlanId vDhcpMacRuleStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 21-3...
DHCP rules are most often used in combination with IP network address rules. A DHCP client has an IP address of all zeros (0.0.0.0) until it receives an IP address from a DHCP server, so it would not match any IP network address rules. page 21-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 773
Defines a generic DHCP rule for an existing VLAN. Mobile ports that receive DHCP frames that do not match other DHCP rules are tempo- rarily assigned to the VLAN. show vlan Displays existing VLANs. show vlan rules Displays rules defined for VLANs. OmniSwitch 6250 CLI Reference Guide November 2009 page 21-5...
IP address as part of the rule, similar to IP network address rule definitions. • Rules are only assigned to existing VLANs. Use the vlan command to create a new VLAN. page 21-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 775
DHCP frames that do not match other DHCP rules are tempo- rarily assigned to the VLAN. show vlan Displays existing VLANs. show vlan rules Displays rules defined for VLANs. MIB Objects vDhcpPortRuleTable vDhcpPortRuleIfIndex vDhcpPortRuleVlanId vDhcpPortRuleStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 21-7...
Rules are only assigned to existing VLANs. Use the vlan command to create a new VLAN. Examples -> vlan 10 dhcp generic -> vlan 10 no dhcp generic Release History Release 6.6.1; command was introduced. page 21-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 777
VLAN. show vlan Displays existing VLANs. show vlan rules Displays rules defined for VLANs. MIB Objects vDhcpGenericRuleTable vDhcpGenericRuleVlanId vDhcpGenericRuleStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 21-9...
Rules are only assigned to existing VLANs. Use the vlan command to create a new VLAN. Examples -> vlan 10 mac 00:00:39:59:0a:0c -> vlan 20 mac 00:00:39:4f:f1:22 -> vlan 10 no mac 00:00:39:59:0a:0c Release History Release 6.6.1; command was introduced. page 21-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 779
MAC address that falls within the range specified by this rule are temporarily assigned to the VLAN. show vlan Displays existing VLANs. show vlan rules Displays rules defined for VLANs. MIB Objects vMacRuleTable vMacRuleAddr vMacRuleVlanId vMacRuleStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 21-11...
Rules are only assigned to existing VLANs. Use the vlan command to create a new VLAN. Examples -> vlan 10 mac range 00:00:39:59:0a:0c 00:00:39:59:0a:0f -> vlan 10 no mac range 00:00:39:59:0a:0c page 21-12 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 781
MAC address that matches the address specified by this rule are temporarily assigned to the VLAN. show vlan Displays existing VLANs. show vlan rules Displays rules defined for VLANs. MIB Objects vMacRangeRuleTable vMacRangeRuleLoAddr vMacRangeRuleHiAddr vMacRangeRuleVlanId vMacRangeRuleStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 21-13...
-> vlan 10 ip 51.0.0.0 255.0.0.0 -> vlan 20 ip 21.0.0.0 -> vlan 10 no ip 21.0.0.0 255.0.0.0 -> vlan 10 no ip 51.0.0.0 Release History Release 6.6.1; command was introduced. page 21-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 783
DHCP frames that do not match other DHCP rules are tempo- rarily assigned to the VLAN. show vlan Displays existing VLANs. show vlan rules Displays rules defined for VLANs. MIB Objects vIpNetRuleTable vIpNetRuleAddr vIpNetRuleMask vIpNetRuleVlanId vIpNetRuleStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 21-15...
IP protocol rules, a message displays recommending the use of the IP generic rule. • Protocol rules take precedence behind DHCP, binding, MAC address, and network address rules. page 21-16 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 785
-> vlan 50 no protocol snap 80FE Release History Release 6.6.1; command was introduced. Related Commands show vlan Displays existing VLANs. show vlan rules Displays rules defined for VLANs. MIB Objects vProtocolRuleTable vProtoRuleProtoClass vProtoRuleEthertype vProtoRuleDsapSsap vProtoRuleVlanId vProtoRuleStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 21-17...
An alternative to port rules is to manually assign a port to a VLAN by using the vlan port default command. This applies to both mobile and non-mobile ports. • Rules are only assigned to existing VLANs. Use the vlan command to create a new VLAN. page 21-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 787
-> vlan 600 no port 2/14-20 7/1-9 Release History Release 6.6.1; command was introduced. Related Commands show vlan Displays existing VLANs. show vlan rules Displays rules defined for VLANs. MIB Objects vPortRuleTable vPortRuleIfIndes vPortRuleVlanId vPortRuleStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 21-19...
IP and Appletalk traffic and VLAN 10 has an IP protocol rule and VLAN 20 has an appletalk protocol rule, the mobile port and its device dynamically join both VLANs. However, certain rules, such as MAC address rules, can limit port membership to one VLAN. page 21-20 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 789
Enables default VLAN membership for mobile port traffic that does not match any VLAN rules. vlan port authenticate Enables or disables authentication on a mobile port. show vlan port mobile Displays mobile port properties. MIB Objects vMobilePortTable vMobilePortIIfIndex vMobilePortMobility vMobilePortIgnoreBPDU OmniSwitch 6250 CLI Reference Guide November 2009 page 21-21...
-> vlan port 3/1 default vlan restore enable -> vlan port 5/2 default vlan restore disable -> vlan port 6/1-32 8/10-24 9/3-14 default vlan restore enable Release History Release 6.6.1; command was introduced. page 21-22 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 791
Enables default VLAN membership for mobile port traffic that does not match any VLAN rules. vlan port authenticate Enables or disables authentication on a mobile port. show vlan port mobile Displays mobile port properties. MIB Objects vMobilePortTable vMobilePortIIfIndex vMobilePortDefVlanRestore OmniSwitch 6250 CLI Reference Guide November 2009 page 21-23...
Examples -> vlan port 3/1 default vlan enable -> vlan port 5/2 default vlan disable -> vlan port 6/1-32 8/10-24 9/3-14 default vlan enable Release History Release 6.6.1; command was introduced. page 21-24 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 793
Enables default VLAN restore on a mobile port. vlan port authenticate Enables or disables authentication on a mobile port. show vlan port mobile Displays mobile port properties. MIB Objects vMobilePortTable vMobilePortIIfIndex vMobilePortDefVlanEnable OmniSwitch 6250 CLI Reference Guide November 2009 page 21-25...
Configures Ethernet ports as mobile ports. vlan port 802.1x Enables or disables 802.1X port-based access control on a mobile port. show vlan port mobile Displays mobile port properties. MIB Objects vMobilePortTable vMobilePortIIfIndex vMobilePortAuthenticate page 21-26 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands vlan port mobile Configures Ethernet ports as mobile ports. vlan port authenticate Enables or disables authentication on a mobile port. show vlan port mobile Displays mobile port properties. OmniSwitch 6250 CLI Reference Guide November 2009 page 21-27...
Page 796
Port Mobility Commands MIB Objects vMobilePortTable vMobilePortIIfIndex vMobilePortAuthenticate page 21-28 OmniSwitch 6250 CLI Reference Guide November 2009...
The type of rule defined. There are several types of VLAN rules: binding rules, MAC address rules, IP network address rules, protocol rules, port rules, custom rules, and DHCP rules. Identifies a binding rule. The asterisk appears next to the rule type. OmniSwitch 6250 CLI Reference Guide November 2009 page 21-29...
Page 798
Related Commands show vlan Displays a list of existing VLANs. show vlan port Displays VLAN port assignments for all VLANs, a specific VLAN, or for a specific port (mobile and fixed). page 21-30 OmniSwitch 6250 CLI Reference Guide November 2009...
VLAN. Use the vlan port mobile to enable or disable mobility on a port. cfg def The configured default VLAN for the port, which is assigned using the vlan port default command. OmniSwitch 6250 CLI Reference Guide November 2009 page 21-31...
Page 800
Release History Release 6.6.1; command was introduced. Related Commands show vlan port Displays VLAN port assignments for all VLANs, a specific VLAN, or for a specific port. page 21-32 OmniSwitch 6250 CLI Reference Guide November 2009...
A summary of the available commands is listed here: vlan vlan stp vlan mobile-tag vlan authentication vlan port default vlan source-learning show vlan show vlan port show vlan router mac status show vlan gvrp show vlan ipmvlan OmniSwitch 6250 CLI Reference Guide November 2009 page 22-1...
A numeric value (2–4094) that uniquely identifies an individual VLAN. This value becomes the VLAN ID for the new VLAN. description Text string up to 32 characters. Use quotes around string if description contains multiple words with spaces between them (e.g. “Alcatel-Lucent Marketing VLAN”). enable Enable VLAN administrative status.
Page 803
Statically assigns ports to a VLAN. show vlan Displays a list of existing VLANs. show vlan port Displays VLAN port assignments. MIB Objects vlanTable vlanNumber vlanDescription vlanAdmStatus vlanOperStatus vlanStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 22-3...
To create more than 252 VLANs in the 1x1 Spanning Tree mode, use the vlan stp disable, vlan 1x1 stp disable, or vlan flat stp disable command to create a VLAN with Spanning Tree disabled. page 22-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 805
Selects a flat Spanning Tree or 1x1 Spanning Tree operating mode for a switch. show vlan Displays a list of existing VLANs. show vlan port Displays VLAN port assignments. MIB Objects vlanTable vlanNumber vlanStpStatus vlan1x1StpStatus vlanflatStpStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 22-5...
Page 807
VLAN Management Commands Related Commands vlan Creates a VLAN. show vlan Displays a list of existing VLANs. show vlan port Displays VLAN port assignments. MIB Objects vlanTable vlanNumber vlanTagMobilePortStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 22-7...
-> vlan 200 port default 29 -> vlan 10 no port default 3/1 -> vlan 20 no port default 4/1-24 -> vlan 30 no port default 5/1-8 6/12-24 -> vlan 200 no port default 29 page 22-8 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 809
Release 6.6.1; command was introduced. Related Commands vlan Creates a VLAN. show vlan Displays list of existing VLANs. show vlan port Displays VLAN port assignments. MIB Objects vpaTable vpaVlanNumber vpaIfIndex vpaType vpaState vpaStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 22-9...
Static MAC addresses associated with a VLAN or IMPVLAN are not cleared when source learning is disabled for the VLAN or IMPVLAN. Examples -> vlan 10-15 source-learning disable -> vlan ipmvlan 10 source-learning disable Release History Release 6.6.1; command was introduced. page 22-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 811
Displays the VLAN configuration for the switch. show vlan ipmvlan Displays IPMVLAN information for a specific IPMVLAN, a range of IPMVLANs, or all the IPMVLANs. MIB Objects vlanTable vlanEntry vlanNumber vlanStatus vlanMacLearningControlStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 22-11...
: VLAN 100, Administrative State: enabled, Operational State : disabled, 1x1 Spanning Tree State : disabled, Flat Spanning Tree State : enabled, IP Router Port : off, IP MTU : 1500, page 22-12 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 813
Type of traffic passing through the VLAN. For example, customer traf- fic tunneled through a VLAN Stacking Ethernet Service VLAN (SVLAN). Note this VLAN Stacking is supported only on Metro switches. Priority-Map Priority map value set for the VLAN. OmniSwitch 6250 CLI Reference Guide November 2009 page 22-13...
Page 814
Displays IPMVLAN information for a specific IPMVLAN, a range of IPMVLANs, or all the IPMVLANs. show ip interface Displays IP router information. MIB Objects vlanMgrVlan vlanTable vlanNumber vlanDescription vlanAdmStatus vlanOperStatus vlanStatus vlanStpStatus vlanAuthentStatus vlanIpAddress vlanIpMask vlanIpEnacp vlanIpForward vlanIpStatus vlanTagMobilePortStatus page 22-14 OmniSwitch 6250 CLI Reference Guide November 2009...
VLAN IDs— is allowed with this command. Multiple entries are not accepted. Examples -> show vlan port vlan port type status +-----+-------+---------+------------+ default inactive default blocking mobile forwarding 11/4 qtagged forwarding qtagged blocking 11/4 default forwarding dynamic forwarding OmniSwitch 6250 CLI Reference Guide November 2009 page 22-15...
Page 816
VLAN. When the operational status is enabled, then VLAN properties (e.g. router interfaces, Spanning Tree) are applied to ports and traffic flow. A VLAN must have an enabled administrative status before it can become operationally enabled. page 22-16 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 817
Displays IPMVLAN information for a specific IPMVLAN, a range of IPMVLANs, or all the IPMVLANs. show ip interface Displays IP router information. MIB Objects vlanMgrVpa vpaTable vpaVlanNumber vpaIfIndex vpaType vpaState vpaStatus vlanMgrVlan vlanTable vlanAdmStatus vlanOperStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 22-17...
The total number of VLANs configured on the switch that have an IP router interface defined. Use the ip interface command to define an IP router for a VLAN. Release History Release 6.6.1; command was introduced. page 22-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 819
Displays list of VLANs configured on the switch. show vlan port Displays VLAN port assignments. show ip interface Displays VLAN IP router interface information. MIB Objects vlanMgrVlanSet vlanSetMultiRtrMacStatus vlanSetVlanCount vlanSetVlanRouterCount vlanSetIpRouterCount OmniSwitch 6250 CLI Reference Guide November 2009 page 22-19...
VLAN. When the operational status is enabled, then VLAN properties (e.g. router interfaces, Spanning Tree) are applied to ports and traffic flow. A VLAN must have an enabled administrative status before it can become operationally enabled. page 22-20 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 821
ID is specified for the VLAN description. Release History Release 6.6.1; command was introduced. Related Commands show vlan Displays a list of VLANs configured on the switch. show vlan port Displays VLAN port assignments. OmniSwitch 6250 CLI Reference Guide November 2009 page 22-21...
1202 Vstk ipmtv VLAN 1202 1203 Entp ipmtv VLAN 1203 -> show vlan ipmvlan 50 Name : VLAN 50, IPMV Mode : Enterprise IPMVLAN Administrative State: enabled, Operational State : disabled, OmniSwitch 6250 CLI Reference Guide November 2009 page 22-23...
Page 824
VLAN ports (forwarding or blocking); off (disabled) prevents Span- ning Tree algorithm from controlling VLAN ports, leaving active ports in a forwarding state. Configured through the vlan stp command. Release History Release 6.6.1; command was introduced. page 22-24 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 825
Creates an IP Multicast VLAN. show vlan Displays a list of VLANs configured on the switch. show vlan port Displays VLAN port assignments. MIB Objects vlanTable vlanNumber vlanDescription vlanTrafficType alavlanOperStatus alavlanAdmStatus alavlanStpStatus alavlan1x1StpStatus alavlanflatStpStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 22-25...
1x1 mode. Examples -> gvrp -> no gvrp Release History Release 6.6.1; command was introduced. Related Commands show gvrp configuration Displays the global configuration for GVRP. MIB Objects dot1qGvrpStatus page 23-2 OmniSwitch 6250 CLI Reference Guide November 2009...
To use the agg_num parameter, the link aggregate group should be created and enabled. Examples -> gvrp port 3/2 -> no gvrp port 3/2 -> gvrp linkagg 2 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-3...
Page 830
Displays the GVRP configuration for all the ports. show gvrp configuration Displays the GVRP configuration for a specific port or an aggregate of linkagg/port ports. MIB Objects dot1qPortVlanTable dot1qPortGvrpStatus page 23-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Examples -> gvrp transparent switching -> no gvrp transparent switching Release History Release 6.6.1; command was introduced. Related Commands show gvrp configuration Displays the global configuration for GVRP. MIB Objects alaGvrpTransparentSwitching OmniSwitch 6250 CLI Reference Guide November 2009 page 23-5...
VLANs learnt earlier will be maintained. Examples -> gvrp maximum vlan 100 Release History Release 6.6.1; command was introduced. Related Commands show gvrp configuration Displays the global configuration for GVRP. MIB Objects alaGvrpMaxVlanLimit page 23-6 OmniSwitch 6250 CLI Reference Guide November 2009...
To use the agg_num parameter, the link aggregate group should be created and enabled. Examples -> gvrp registration forbidden port 3/2 -> no gvrp registration port 3/2 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-7...
Page 834
GVRP Commands Related Commands show gvrp configuration Displays the GVRP configuration for a specific port or an aggregate of linkagg/port ports. MIB Objects alaGvrpPortConfigtable alaGvrpPortConfigRegistrarMode page 23-8 OmniSwitch 6250 CLI Reference Guide November 2009...
To use the agg_num parameter, the link aggregate group should be created and enabled. Examples -> gvrp applicant active port 2/2 -> no gvrp applicant port 2/2 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-9...
Page 836
GVRP Commands Related Commands show gvrp configuration Displays the GVRP configuration for a specific port or an aggregate of linkagg/port ports. MIB Objects alaGvrpPortConfigtable alaGvrpPortConfigApplicantMode page 23-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Leave timer value should be greater than or equal to three times the Join timer value. • Leaveall timer value should be greater than or equal to the Leave timer value. • To use the agg_num parameter, the link aggregate group should be created and enabled. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-11...
Page 838
Displays the timer values configured for all the ports or a specific port. show gvrp configuration Displays the GVRP configuration for a specific port or an aggregate of linkagg/port ports. MIB Objects alaGvrpPortConfigTable alaGvrpPortConfigJoinTimer alaGvrpPortConfigLeaveTimer alaGvrpPortConfigLeaveAllTimer page 23-12 OmniSwitch 6250 CLI Reference Guide November 2009...
-> gvrp restrict-vlan-registration port 3/1 5 -> no gvrp restrict-vlan-registration port 3/1 5 -> gvrp restrict-vlan-registration port 3/1 6-10 -> no gvrp restrict-vlan-registration port 3/1 6-10 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-13...
Page 840
Configures the GVRP registration mode for the switch ports. show gvrp configuration Displays the GVRP configuration for a specific port or an aggregate of linkagg/port ports. MIB Objects alaGvrpPortConfigTable alaGvrpPortConfigRestrictedRegistrationBitmap alaGvrpPortConfigAllowRegistrationBitmap alaGvrpPortConfigRegistrationBitmap page 23-14 OmniSwitch 6250 CLI Reference Guide November 2009...
-> gvrp restrict-vlan-advertisement port 3/1 6-9 -> no gvrp restrict-vlan-advertisement port 3/1 6-9 -> gvrp restrict-vlan-advertisement linkagg 3 10 -> no gvrp restrict-vlan-advertisement linkagg 3 10 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-15...
Page 842
Configures the applicant mode for the switch port. show gvrp configuration Displays the GVRP configuration for a specific port or an aggregate of linkagg/port ports. MIB Objects alaGvrpPortConfigTable alaGvrpPortConfigRestrictedApplicantBitmap alaGvrpPortConfigAllowApplicantBitmap alaGvrpPortConfigApplicantBitmap page 23-16 OmniSwitch 6250 CLI Reference Guide November 2009...
-> gvrp static-vlan restrict port 3/2 6-9 -> no gvrp static-vlan restrict port 3/2 6-9 -> gvrp static-vlan restrict linkagg 3 4-5 -> no gvrp static-vlan aggregate linkagg 3 4-5 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-17...
Page 844
GVRP Commands Related Commands show gvrp configuration Displays the GVRP configuration for a specific port or an aggregate of linkagg/port ports. MIB Objects alaGvrpPortConfigTable alaGvrpPortConfigRegistrationToStaticVlan alaGvrpPortConfigRegistrationToStaticVlanLearn alaGvrpPortConfigRegistrationToStaticVlanRestrict page 23-18 OmniSwitch 6250 CLI Reference Guide November 2009...
Release 6.6.1; command was introduced. Related Commands show gvrp statistics Displays the GVRP statistics or all the ports, an aggregate of ports, or a specific port. MIB Objects alaGvrpGlobalClearStats alaGvrpPortStatsTable alaGvrpPortStatsClearStats OmniSwitch 6250 CLI Reference Guide November 2009 page 23-19...
Garp Msgs Transmitted : 2693, Invalid Msgs Received -> show gvrp statistics Port 1/1: Join Empty Received : 0, Join In Received : 0, Empty Received : 0, Leave Empty Received : 0, page 23-20 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 847
The number of Join Empty messages transmitted. Join In Transmitted The number of Join In messages transmitted. Empty Transmitted The number of Empty messages transmitted. Leave Empty Transmitted The number of Leave Empty messages transmitted. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-21...
Page 848
Clears GVRP statistics for all the ports, an aggregate of ports, or a spe- cific port. MIB Objects alaGvrpPortStatsTable alaGvrpPortStatsJoinEmptyReceived alaGvrpPortStatsJoinInReceived alaGvrpPortStatsEmptyReceived alaGvrpPortStatsLeaveInReceived alaGvrpPortStatsLeaveEmptyReceived alaGvrpPortStatsLeaveAllReceived alaGvrpPortStatsJoinEmptyTransmitted alaGvrpPortStatsJoinInTransmitted alaGvrpPortStatsEmptyTransmitted alaGvrpPortStatsLeaveInTransmitted alaGvrpPortStatsLeaveEmptyTransmitted alaGvrpPortStatsLeaveAllTransmitted dot1qPortGvrpFailedRegistrations alaGvrpPortStatsTotalPDUReceived alaGvrpPortStatsTotalPDUTransmitted alaGvrpPortStatsInvalidMsgsReceived alaGvrpPortStatsTotalMsgsReceived alaGvrpPortStatsTotalMsgsTransmitted page 23-22 OmniSwitch 6250 CLI Reference Guide November 2009...
Last-PDU Origin The source MAC address of the last PDU message received on the spe- cific port. Release History Release 6.6.1; command was introduced. Related Commands MIB Objects Dot1qPortvlantable dot1qPortGvrpLastPduOrigin OmniSwitch 6250 CLI Reference Guide November 2009 page 23-23...
(No). When enabled, GVRP messages are flooded even if GVRP is dis- abled for the switch. Maximum VLAN Limit The maximum number of VLANs that can be learned by GVRP in the system. Release History Release 6.6.1; command was introduced. page 23-24 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 851
Enables GVRP on the device globally. gvrp transparent switching Enables transparent switching on the device. gvrp maximum vlan Configures the maximum number of dynamic VLANs that can be learned by GVRP. MIB Objects dot1qGvrpStatus alaGvrpTransparentSwitching alaGvrpMaxVlanLimit OmniSwitch 6250 CLI Reference Guide November 2009 page 23-25...
Page 853
Enables GVRP on a specific port or an aggregate of ports on the switch. show gvrp configuration Displays the GVRP configuration for a specific port or an aggregate of linkagg/port ports. MIB Objects Dot1qportvlantable dot1qPortGvrpStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 23-27...
Page 855
Indicates if the VLAN is restricted (TRUE) or not restricted (FALSE) from dynamic registration on the port. Restricted Applicant Indicates if the restricted applicant mode is enabled (TRUE) or not (FALSE). Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-29...
Page 856
VLANs. show gvrp configuration port Displays the GVRP configuration status for all the ports. MIB Objects Dot1qportvlantable dot1qPortGvrpLastPduOrigin dot1qPortGvrpStatus alaGvrpPortConfigTable alaGvrpPortConfigRegistrarMode alaGvrpPortConfigApplicantMode alaGvrpPortConfigJoinTimer alaGvrpPortConfigLeaveTimer alaGvrpPortConfigLeaveAllTimer alaGvrpPortConfigRestrictedRegistrationBitmap alaGvrpPortConfigRegistrationToStaticVlan alaGvrpPortConfigPropagateDynamicNonGvrpVlan page 23-30 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 858
Leave Timer (msec) : 1800 -> show gvrp timer leaveall port 1/21 LeaveAll Timer (msec) : 30000 -> show gvrp timer join Legend : All timer values are in milliseconds Port Join Timer --------+---------------- page 23-32 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 859
1/43 1/44 1/45 1/46 1/47 1/48 1/49 1/50 -> show gvrp timer leave Legend : All timer values are in milliseconds Port Leave Timer --------+---------------- 1800 1800 1800 1800 1800 1800 OmniSwitch 6250 CLI Reference Guide November 2009 page 23-33...
Page 860
1800 1/49 1800 1/50 1800 -> show gvrp timer leaveall Legend : All timer values are in milliseconds Port LeaveAll Timer --------+---------------- 30000 30000 30000 30000 30000 30000 30000 30000 30000 page 23-34 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 861
Displays the Join timer value in milliseconds. Leave Timer Displays the Leave timer value in milliseconds. LeaveAll Timer Displays the LeaveAll timer value in milliseconds. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 23-35...
Page 862
GVRP Commands Related Commands gvrp timer Configures the Join, Leave, or LeaveAll timer values for the switch ports. MIB Objects alaGvrpPortConfigTable alaGvrpPortConfigJoinTimer alaGvrpPortConfigLeaveTimer alaGvrpPortConfigLeaveAllTimer page 23-36 OmniSwitch 6250 CLI Reference Guide November 2009...
24 VLAN Stacking Commands The VLAN Stacking feature provides a method for tunneling multiple customer VLANs (CVLAN) through a service provider network using one or more service provider VLANs by way of 802.1Q double tagging or VLAN Translation. This feature enables service providers to provide their customers with Transparent LAN Services (TLS).
An alphanumeric string of up to 32 characters. Use quotes around the string if the VLAN name contains multiple words with spaces between them (e.g., “Alcatel-Lucent Engineering”). Defaults By default, the Spanning Tree status is enabled in both the 1x1 and flat mode when the SVLAN or IPMV...
Page 865
VLAN Stacking Commands Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines • Use the no form of this command to delete an SVLAN or a range of SVLANs. Note that SVLAN port associations are also removed when the SVLAN is deleted.
| disable enable Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines • By default, source MAC address learning is enabled on all the SVLANs. • Disabling source learning on an SVLAN clears all the dynamically learned MAC addresses associated with the VLAN from the MAC address table.
Page 867
VLAN Stacking Commands Related Commands ethernet-service Creates a VLAN Stacking VLAN (SVLAN). show ethernet-service vlan Displays a list of SVLANs configured for the switch. MIB Objects vlanTable vlanEntry vlanNumber vlanStatus vlanMacLearningControlStatus OmniSwitch CLI Reference Guide November 2009 page 24-5...
The name of the VLAN Stacking service; an alphanumeric string of up to 32 characters. Use quotes around string if the service name contains multiple words with spaces between them (e.g., “Alcatel-Lucent Engi- neering”). svid The VLAN ID number that identifies an existing SVLAN or IPMV to associate with the VLAN Stacking service (2–4094).
Page 869
VLAN Stacking Commands Related Commands ethernet-service Creates an SVLAN for customer traffic, a management VLAN for pro- vider traffic, or an IPMV for multicast traffic. MIB Objects alaEServiceTable alaEServiceID alaEServiceSVLAN alaEServiceVlanType alaEServiceRowStatus OmniSwitch CLI Reference Guide November 2009 page 24-7...
A switch port or link aggregate becomes a VLAN Stacking NNI port by default when the port or link aggregate is associated with an SVLAN. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines • Use the no form of this command to remove an association between an NNI port and an SVLAN. Note that when the last SVLAN association is removed, the NNI port reverts to a conventional switch port.
Page 871
VLAN Stacking Commands Release History Release 6.6.1; command was introduced. Related Commands ethernet-service Creates an SVLAN for customer traffic, a management VLAN for pro- vider traffic, or an IPMV for multicast traffic. ethernet-service nni Configures the vendor TPID value and the legacy BPDU processing sta- tus for a VLAN Stacking Network Network Interface (NNI).
| disable disable gvrp legacy-bpdu enable | disable disable Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines • This command only applies to ports configured as VLAN Stacking NNI ports. • Enable legacy BPDU support only on VLAN Stacking network ports that are connected to legacy BPDU switches.
Page 873
VLAN Stacking Commands • Note that if the peer switch connected to the VLAN Stacking network port supports the Provider MAC address (i.e., STP, 802.1ad/D6.0 MAC), then enabling legacy BPDU support is not required on the network port. Refer to the following table to determine the type of STP or GVRP MAC used: Customer MAC {0x01, 0x80, 0xc2, 0x00, 0x00, 0x00} Provider MAC address (802.1ad/D6.0)
Defaults The “default-sap-profile” profile is automatically associated with the SAP ID when the SAP is created. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines • Use the no form of this command to delete a VLAN Stacking SAP. When a SAP is deleted, all port and CVLAN associations with the SAP are also deleted.
Page 875
VLAN Stacking Commands Related Commands ethernet-service service-name Creates a VLAN Stacking service and associates the service with an SVLAN or an IP Multicast VLAN (IPMV). ethernet-service sap-profile Creates a VLAN Stacking SAP profile. ethernet-service sap sap-profile Associates a SAP profile with a SAP ID. MIB Objects alaEServiceSapTable alaEServiceSapID...
A switch port or a link aggregate becomes a VLAN Stacking UNI port by default when the port or link aggregate is associated with a VLAN Stacking SAP. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines • Use the no form of this command to remove an association between a UNI port and a SAP. Note that when the last SAP association is removed, the UNI port converts back to a conventional switch port.
Page 877
VLAN Stacking Commands Release History Release 6.6.1; command was introduced. Related Commands ethernet-service sap Creates a VLAN Stacking SAP and associates the SAP with a VLAN Stacking SAP profile and service. ethernet-service sap sap-profile Creates a UNI profile that is used to specify how to process control packets ingressing on UNI ports.
Defaults By default, no CVLAN traffic is associated with the SAP ID when the SAP is created. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines • Use the no form of this command to remove a CVLAN ID or the designation for all or untagged frames from the SAP.
Page 879
VLAN Stacking Commands • Only one SAP with the all or untagged option per UNI is allowed. For example, if UNI port 1/17 is part of SAP 10 and SAP 20 and SAP 10 is configured for all traffic, then only untagged or a CVLAN ID is allowed for SAP 20.
Syntax Definitions sap-profile-name Alphanumeric string of up to 32 characters. Use quotes around string if the profile name contains multiple words with spaces between them (e.g., “Alcatel-Lucent Engineering”). bandwidth not-assigned This parameter is not supported. shared Shares the ingress bandwidth limit across all SAP ports and CVLANs.
Page 881
Use the cir, cbs, pir, and pbs traffic control parameters to configure Tri-Color Marking (TCM) ingress rate limiting/policing for the SAP profile. These parameters are applied to packets serviced by the SAP. For more information about TCM, see the “Configuring QoS” chapter in the OmniSwitch 6250 Network Configuration Guide.
Page 882
VLAN Stacking Commands Related Commands ethernet-service sap Creates a VLAN Stacking SAP and associates the SAP with a service. ethernet-service sap sap-profile Associates a SAP profile with a SAP ID. show ethernet-service sap-profile Displays the profile attribute configuration for a SAP profile. show ethernet-service statistics Displays the TCM packet counts by service or for a specific SAP ID.
Defaults The “default-sap-profile” profile is automatically associated with the SAP ID when the SAP is created. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines • If a profile association already exists for the specified SAP ID, the current profile is replaced with the profile specified with this command.
Page 884
VLAN Stacking Commands Related Commands ethernet-service sap Creates a VLAN Stacking SAP and associates the SAP with a VLAN Stacking SAP profile and service. ethernet-service sap-profile Creates a VLAN Stacking SAP profile. MIB Objects alaEServiceSapTable alaEServiceSapID alaEServiceSapProfile alaEServiceSapRowStatus page 24-22 OmniSwitch CLI Reference Guide November 2009...
• Use the show ethernet-service statistics command to display the current statistics for TCM packet counts. • For more information about TCM, see the “Configuring QoS” chapter in the OmniSwitch 6250 Network Configuration Guide. Examples -> ethernet-service statistics reset Release History Release 6.6.1;...
Discards the specified PDU. tunnel Tunnels the specified PDU across the provider network. Defaults parameter default tunnel 802.1x discard 802.3ad peer 802.1ab discard gvrp tunnel amap discard Platforms Supported OmniSwitch 6250-Metro Models page 24-24 OmniSwitch CLI Reference Guide November 2009...
Page 887
VLAN Stacking Commands Usage Guidelines • Use the no form of this command to delete a UNI profile. • Remove any UNI profile associations with UNI ports before attempting to modify or delete the profile. • Up to five unique UNI profile combinations, including the default profile, are allowed per switch. If a profile has the same processing settings as any other profile, the profile is not considered unique.
The default profile (default-uni-profile) is used to process control packets ingressing on a UNI port. This profile is assigned at the time a port is configured as a VLAN Stacking UNI. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines • This UNI specified with this command must already exist in the switch configuration.
Page 890
VLAN Stacking Commands Related Commands ethernet-service sap sap-profile Creates a UNI profile that is used to specify how to process control packets ingressing on UNI ports. ethernet-service sap uni Configures the switch port as a VLAN Stacking UNI and associates the port with a VLAN Stacking Service Access Point (SAP).
Displays the active VLAN Stacking mode for the switch. show ethernet-service mode Syntax Definitions Defaults Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines This command is available in both modes: Legacy or EServices. Examples -> show ethernet-service mode Vlan Stacking Mode: Legacy Mode ->...
By default, all SVLANs are displayed if an SVLAN or range of SVLANs is not specified with this command. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines Specify a single SVLAN ID or a range of SVLAN IDs to display configuration information for a specific SVLAN or range of SVLANs.
Page 893
VLAN Stacking Commands Related Commands ethernet-service Creates a VLAN Stacking VLAN (SVLAN) for tunneling customer traf- fic, a management SVLAN for provider traffic, or an SVLAN that the IP Multicast VLAN (IPMV) application will use to distribute multicast traffic. show ethernet-service Displays configuration information for VLAN Stacking Ethernet ser- vices.
Syntax Definitions service-name The name of an existing VLAN Stacking service. Use quotes around string if the service name contains multiple words with spaces between them (e.g., “Alcatel-Lucent Engineering”). svid The VLAN ID number that identifies an existing SVLAN (2–4094). Defaults By default, all services are displayed if a service name or SVLAN ID is not specified with this command.
Page 895
VLAN Stacking Commands Service Name : ipmv_service IPMVLAN : 40 NNI(s) : No NNIs configured SAP Id UNIs : 1/22 CVLAN(s) : 100 sap-profile : translate_profile -> show ethernet-service service-name CustomerABC Service Name : CustomerABC SVLAN : 255 NNI(s) : 1/22 SAP Id : 10 UNIs...
Page 896
VLAN Stacking Commands Related Commands ethernet-service service-name Creates a VLAN Stacking service and associates the service with an SVLAN or an IPMVLAN. show ethernet-service vlan Displays a list of all or a range of configured SVLANs or the parameters of a specified SVLAN. MIB Objects alaEServiceTable alaEServiceID...
The SAP ID number identifying the service instance. Defaults By default, all SAPs are displayed if a SAP ID is not specified with this command. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines Specify a single SAP ID to display configuration information for a specific SAP. Examples ->...
Page 898
VLAN Stacking Commands output definitions SAP Id The ID number for the VLAN Stacking Service Access Point that is applied to the service. UNIs VLAN Stacking User Network Interface ports that receive customer traffic. CVLAN(s) Customer VLAN IDs ingressing on UNI ports. sap-profile The name of the SAP profile associated with the SAP.
(e.g., 3/1 specifies port 1 on slot 3). agg_num The link aggregate ID number (0–31). Defaults Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines Specifying a slot/port or link aggregate ID number is required with this command. Examples -> show ethernet-service port 1/10...
Page 900
VLAN Stacking Commands -> show ethernet-service port 1/22 Interface : 1/22 Port Type : NNI Service Name : CustomerABC SVLAN : 255 NNI(s) : 1/22 SAP Id : 10 UNIs : 2/10, 2/11 CVLAN(s) : 500, 600 sap-profile : default-sap-profile Service Name : Video-Service SVLAN : 300...
Page 901
VLAN Stacking Commands Related Commands ethernet-service svlan nni Configures the switch port as a VLAN Stacking NNI port and associates the port with a customer SVLAN, management SVLAN, or an IP Multi- cast VLAN (IPMV). ethernet-service sap uni Configures the switch port as a VLAN Stacking UNI and associates the port with a VLAN Stacking SAP.
By default, all NNI ports are displayed if a slot/port or link aggregate ID number is not specified. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines Specify a slot/port or link aggregate ID number to display information for a single slot/port or link aggre- gate ID.
Page 903
VLAN Stacking Commands Release History Release 6.6.1; command was introduced. Related Commands ethernet-service svlan nni Configures the switch port as a VLAN Stacking NNI port and associates the port with a customer SVLAN, management SVLAN, or an IP Multi- cast VLAN (IPMV). ethernet-service nni Configures the vendor TPID value and the legacy BPDU processing sta- tus for a VLAN Stacking Network Network Interface (NNI).
By default, profile information for all UNI ports is displayed if a slot/port or link aggregate ID number is not specified. Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines Specify a slot/port or link aggregate ID number to display information for a single slot/port or link aggre- gate ID.
Page 905
VLAN Stacking Commands Related Commands ethernet-service sap sap-profile Creates a UNI profile that is used to specify how to process control packets ingressing on UNI ports. ethernet-service uni uni-profile Associates a VLAN Stacking UNI profile with a UNI port. show ethernet-service uni- Displays the profile attribute configuration for VLAN Stacking User profile Network Interface (UNI) profiles.
Indicates how IEEE 802.1AB control packets are processed. GVRP Indicates how GARP VLAN Registration Protocol packets are pro- cessed. AMAP Indicates how Alcatel-Lucent Mapping adjacency Protocol packets are processed. Release History Release 6.6.1; command was introduced. page 24-44 OmniSwitch CLI Reference Guide...
Page 907
VLAN Stacking Commands Related Commands ethernet-service sap sap-profile Creates a UNI profile that is used to specify how to process control packets ingressing on UNI ports. ethernet-service uni uni-profile Associates a VLAN Stacking UNI profile with a UNI port. show ethernet-service uni Displays the profile associations for VLAN Stacking User Network Interface (UNI) ports.
The ingress bandwidth value is displayed in megabytes. • The Tri-Color Marking (TCM) parameter values (CIR, CBS, PIR, and PBS) are displayed in kilobytes. For more information about TCM, see the “Configuring QoS” chapter in the OmniSwitch 6250 Network Configuration Guide. Examples ->...
Page 909
VLAN Stacking Commands output definitions Bandwidth Sharing The status of bandwidth sharing (enable or disable). If enabled, the ingress bandwidth value is shared across all SAP ports and CVLANs. If disabled, the bandwidth value is not shared and applied to individual SAP ports and CVLANs.
• Specify a SAP ID with this command to display packet counts for a specific SAP. • For more information about TCM, see the “Configuring QoS” chapter in the OmniSwitch 6250 Network Configuration Guide. Examples In the following examples, Customer A is associated with a SAP configured with shared bandwidth and Customer B is associated with a SAP configured with the bandwidth not shared.
Page 911
VLAN Stacking Commands -----+----------------+---------------+---------------+------------- -> show ethernet-service sap 1 statistics Port CVLAN Green Yellow Total -----+-------+--------------+---------------+---------------+------------- -> show ethernet-service service-name customer-b statistics Green Yellow Total -----+----------------+---------------+---------------+------------- 425633 14101459 14527388 -> show ethernet-service sap 2 statistics Port CVLAN Green Yellow Total -----+-------+--------------+---------------+---------------+------------- 368412 11990964...
The level must be 0-2 at operator level, 3-5 at provider level and 6-7 at customer level when creating the level of domain. Examples -> ethoam domain esd.alcatel-lucent.com format dnsname level 5 -> no ethoam domain esd.alcatel-lucent.com Release History Release 6.6.1; command was introduced.
Page 916
Displays the information of all the Management Domains (MD) configured on the bridge. show ethoam domain Displays the information of a specific Management Domain config- ured on the bridge. MIB Objects Dot1agCfmMd dot1agCfmMdIndex dot1agCfmMdFormat dot1agCfmMdName dot1agCfmMdLevel dot1agCfmMdMhfCreation dot1agCfmMdRowStatus page 25-4 OmniSwitch 6250 CLI Reference Guide November 2009...
OmniSwitch 6250-Metro Models Usage Guidelines The domain_name should be unique amid all those used by or available to the service provider. Examples -> ethoam domain esd.alcatel-lucent.com mhf explicit Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide...
Page 918
Displays the information of all the Management Domains (MD) configured on the bridge. show ethoam domain Displays the information of a specific Management Domain config- ured on the bridge. MIB Objects Dot1agCfmMaintenanceDomain dot1agCfmMdIndex dot1agCfmMdFormat dot1agCfmMdName dot1agCfmMdLevel dot1agCfmMdMhfCreation dot1agCfmMdRowStatus page 25-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Use the no form of this command to remove the Ethernet OAM Maintenance Association. • The association_name should be unique within a domain. Examples -> ethoam association alcatel-sales format string domain esd.alcatel-lucent.com vlan 10 -> no ethoam association alcatel-sales domain esd.alcatel-lucent.com Release History Release 6.6.1;...
Page 920
Related Commands show ethoam domain Displays the information of a specified MA in a Management association Domain configured on the bridge. MIB Objects Dot1agCfmMa dot1agCfmMaIndex dot1agCfmMaFormat dot1agCfmMaName dot1agCfmMaVid dot1agCfmMaMhfCreation dot1agCfmMaCcmInterval dot1agCfmMaRowStatus page 25-8 OmniSwitch 6250 CLI Reference Guide November 2009...
The association_name should be unique amid all those used by or available to the service provider within a domain. Examples -> ethoam association alcatel-sales domain esd.alcatel-lucent.com mhf none Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide...
Page 922
Displays the information of a specified MA in a Management association Domain configured on the bridge. show ethoam default-domain Displays the information of the default MA. MIB Objects Dot1agCfmMa dot1agCfmMaIndex dot1agCfmMaFormat dot1agCfmMaName dot1agCfmMaVid dot1agCfmMaMhfCreation dot1agCfmMaCcmInterval dot1agCfmMaRowStatus page 25-10 OmniSwitch 6250 CLI Reference Guide November 2009...
Usage Guidelines The association_name should be unique amid all those used by or available to the service provider within a domain. Examples -> ethoam association alcatel-sales domain esd.alcatel-lucent.com ccm-interval interval10s Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide...
Page 924
Ethernet OAM Commands Related Commands show ethoam domain Displays the information of a specific Management Domain config- ured on the bridge. MIB Objects Dot1agCfmMa dot1agCfmMaIndex dot1agCfmMaFormat dot1agCfmMaName dot1agCfmMaVid dot1agCfmMaMhfCreation dot1agCfmMaCcmInterval dot1agCfmMaRowStatus page 25-12 OmniSwitch 6250 CLI Reference Guide November 2009...
• The association_name should be unique within a domain. Examples -> ethoam association alcatel-sales domain esd.alcatel-lucent.com endpoint-list 100-200 -> no ethoam association alcatel-sales domain esd.alcatel-lucent.com endpoint-list 100-200 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009...
Page 926
Displays the information of a specified MA in a Management association Domain configured on the bridge. MIB Objects Dot1agCfmMa dot1agCfmMaIndex dot1agCfmMaFormat dot1agCfmMaName dot1agCfmMaVid dot1agCfmMaMhfCreation dot1agCfmMaCcmInterval dot1agCfmMaRowStatus Dot1agCfmMaMepList dot1agCfmMaMepListIdentifier dot1agCfmMaMepListRowStatus page 25-14 OmniSwitch 6250 CLI Reference Guide November 2009...
You cannot add or remove a VLAN from the default MD. Examples -> ethoam default-domain vlan 100 level 4 mhf default -> ethoam default-domain vlan 200 level no-level mhf none -> no ethoam default-domain Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 25-15...
Page 928
Ethernet OAM Commands Related Commands show ethoam default-domain Displays the information of all the default MD. MIB Objects Dot1agCfmDefaultMdLevel dot1agCfmDefaultMdLevelIndex dot1agCfmDefaultMdLevelVid dot1agCfmDefaultMdLevelMhfCreation dot1agCfmDefaultMdLevelLevel page 25-16 OmniSwitch 6250 CLI Reference Guide November 2009...
-> ethoam endpoint 100 domain esd.alcatel-lucent.com association alcatel-sales direction up port 3/10 -> ethoam endpoint 100 domain esd.alcatel-lucent.com association alcatel-sales direction down port 3/10 -> no ethoam endpoint 100 domain esd.alcatel-lucent.com association alcatel-sales OmniSwitch 6250 CLI Reference Guide November 2009 page 25-17...
OmniSwitch 6250-Metro Models Usage Guidelines The mep_id should be unique amid all those used by or available to the service provider in the specified Examples -> ethoam endpoint 100 domain esd.alcatel-lucent.com association alcatel-sales admin-state enable Release History Release 6.6.1; command was introduced.
OmniSwitch 6250 Usage Guidelines The mep_id should be unique amid all those used by or available to the service provider in the specified Examples -> ethoam endpoint 100 domain esd.alcatel-lucent.com association alcatel-sales ccm enable Release History Release 6.6.1; command was introduced.
OmniSwitch 6250-Metro Models Usage Guidelines The mep_id should be unique amid all those used by or available to the service provider in the specified Examples -> ethoam endpoint 100 domain esd.alcatel-lucent.com association alcatel-sales priority 6 Release History Release 6.6.1; command was introduced.
OmniSwitch 6250-Metro Models Usage Guidelines The mep_id should be unique amid all those used by or available to the service provider in the specified Examples -> ethoam endpoint 100 domain esd.alcatel-lucent.com association alcatel-sales lowest-priority-defect all-defect Release History Release 6.6.1; command was introduced.
Sets the drop eligibility bit in the VLAN tag to true. false Sets the drop eligibility bit in the VLAN tag to false. Defaults parameter default number_of_messages true | false true Platforms Supported OmniSwitch 6250-Metro Models OmniSwitch 6250 CLI Reference Guide November 2009 page 25-27...
Page 940
This command is used to validate the connectivity between Maintenance End Points (MEP) and Main- tenance Intermediate Points (MIP). Examples -> ethoam loopback target-macaddress 10:aa:ac:12:12:ad source-endpoint 4 domain esd.alcatel-lucent.com association alcatel-sales number 10 vlan-priority 4 drop-eligible true -> ethoam loopback target-endpoint 15 source-endpoint 4 domain esd.alcatel- lucent.com association alcatel-sales Release History Release 6.6.1;...
This command allows an operator to generate a LTM for the specified MEP. • This command signals the MEP that it should transmit a Linktrace message and detect the presence or lack of the corresponding Linktrace messages. OmniSwitch 6250 CLI Reference Guide November 2009 page 25-29...
• The Fault Notification Generation Alarm timeout value is configurable per MEP. Examples -> ethoam fault-alarm-time 10 endpoint 100 domain esd.alcatel-lucent.com associa- tion alcatel_sales -> no ethoam fault-alarm-time endpoint 100 domain esd.alcatel-lucent.com associa- tion alcatel_sales Release History Release 6.6.1;...
Page 944
Ethernet OAM Commands Related Commands show ethoam Displays the information of all the Management Domains (MD) configured on the bridge. MIB Objects Dot1agCfmMep dot1agCfmMepFngAlarmTime page 25-32 OmniSwitch 6250 CLI Reference Guide November 2009...
• The Fault Notification Generation Reset timer value is configurable per MEP. Examples -> ethoam fault-reset-time 10 end-point 100 domain esd.alcatel-lucent.com associa- tion alcatel_sales -> no ethoam fault-reset-time end-point 100 domain esd.alcatel-lucent.com associa- tion alcatel_sales OmniSwitch 6250 CLI Reference Guide...
Page 946
Configures the timeout value for the Fault Notification Generation Alarm time. show ethoam Displays the information of all the Management Domains (MD) configured on the bridge. MIB Objects Dot1agCfmMep dot1agCfmMepFngResetTime page 25-34 OmniSwitch 6250 CLI Reference Guide November 2009...
Maintenance Domain The name of the maintenance domain. Maintenance Association The name of the maintenance association. Release History Release 6.6.1; command was introduced. Related Commands ethoam domain Creates an Ethernet domain. OmniSwitch 6250 CLI Reference Guide November 2009 page 25-35...
MA-MHFstatus Indicates whether the maintenance entity can create MHFs for this MA. Options include none, explicit, or default. CCM-interval The interval between the CCM transmissions. MEP-Id Indicates the Maintenance End Point. OmniSwitch 6250 CLI Reference Guide November 2009 page 25-37...
Page 950
Displays the information of all the Management Domains (MD) configured on the bridge. ethoam domain Creates an Ethernet domain. MIB Objects Dot1agCfmMd dot1agCfmMdLevel dot1agCfmMdMhfCreation Dot1agCfmMa dot1agCfmMaName dot1agCfmMaVid dot1agCfmMaMhfCreation dot1agCfmMaCcmInterval Dot1agCfmMep dot1agCfmMepIdentifier page 25-38 OmniSwitch 6250 CLI Reference Guide November 2009...
Specifies the MEP of a specific MA. The valid range is 1–8191. Defaults Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines Examples -> show ethoam domain esd.alcatel-lucent.com association alcatel-sales endpoint 3 Admin State : up, Direction : up, Slot/Port: 1/2, MacAddress: 00:D0:95:EC:84:B0, Fault Notification : FNG_RESET,...
Page 954
The lowest priority defect that allowed to generate fault alarm. Highest PrDefect Present The highest priority defect since the MEPs Fault Notification Generator in reset state. Release History Release 6.6.1; command was introduced. page 25-42 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 955
Configures the administrative state of MEP. MIB Objects Dot1agCfmMep dot1agCfmMepActive dot1agCfmMepDirection dot1agCfmMepPortNumber dot1agCfmMepMacAddress dot1agCfmMepFngState dot1agCfmMepCcmEnabled dot1agCfmMepCcmLtmPriority dot1agCfmMepSomeRMepCcmDefect dot1agCfmMepErrorCcmDefect dot1agCfmMepXconCcmDefect dot1agCfmMepSomeRdiDefect dot1agCfmMepErrorCcmLastFailure dot1agCfmMepXconCcmLastFailure dot1agCfmMepErrMacStatus dot1agCfmMepLtmNextSeqNumber dot1agCfmMepFngAlarmTime dot1agCfmMepFngAlarmTime dot1agCfmMepLowPrDef dot1agCfmMepHighestPrDefect OmniSwitch 6250 CLI Reference Guide November 2009 page 25-43...
Indicates the MHF value for a VLAN that is part of the default MD Options include none, explicit, or default. Level The level of the maintenance domain. Release History Release 6.6.1; command was introduced. page 25-44 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 959
Related Commands show ethoam domain Displays the information of a specific MEP in a Management association end-point Domain configured on the bridge. MIB Objects Dot1agCfmMepDb dot1agCfmMepDbRMepIdentifier dot1agCfmMepDbRMepState dot1agCfmMepDbRMepFailedOkTime dot1agCfmMepDbMacAddress dot1agCfmMepDbPortStatusTlv dot1agCfmMepDbInterfaceStatusTlv OmniSwitch 6250 CLI Reference Guide November 2009 page 25-47...
The VLAN ID to which the MEP is attached. Direction Indicates the direction (Inward or Outward) of the Maintenance Point (MP) on the Bridge port. MAC-Address The MEP ID configured on this port. page 25-48 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 961
Release History Release 6.6.1; command was introduced. Related Commands ethoam endpoint Creates an Ethernet OAM Maintenance End Point in the specified MIB Objects Dot1agCfmMd dot1agCfmMdName Dot1agCfmMa dot1agCfmMaName Dot1agCfmStack dot1agCfmStackVlanIdOrNone dot1agCfmStackDirection dot1agCfmStackMacAddress dot1agCfmStackMdLevel OmniSwitch 6250 CLI Reference Guide November 2009 page 25-49...
Specifies the MEP for which LTR is to be displayed. The valid range is 1-8191. Defaults Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines Examples -> show ethoam linktrace-tran-id domain esd.alcatel-lucent.com association alcatel- sales endpoint 3 S.No Transaction Id -------+----------------------- 13357, 13358,...
Page 965
Ethernet OAM Commands Related Commands ethoam linktrace Enables the maintenance entity to initiate transmitting of Link Trace Messages (LTM). MIB Objects Dot1agCfmLtr dot1agCfmLtrSeqNumber OmniSwitch 6250 CLI Reference Guide November 2009 page 25-53...
Specifies the name of Ethernet OAM Association. endpoint_id Specifies a MEP for a specific MA. Defaults Platforms Supported OmniSwitch 6250-Metro Models Usage Guidelines Examples -> show ethoam statistics domain esd.alcatel-lucent.com association alcatel-sales MEP-ID CCM Seq LBR Out LBR Bad Unexpected Error of order...
Page 967
Release 6.6.1; command was introduced. Related Commands ethoam loopback Enables the maintenance entity to initiate transmitting loopback messages (LBMs) and obtaining loopback replies. MIB Objects Dot1agCfmMep dot1agCfmMepIdentifier dot1agCfmMepCcmOut dot1agCfmMepRCcmSequenceErrors dot1agCfmMepLbrIn dot1agCfmMepLbrInOutOfOrder dot1agCfmMepLbrOut dot1agCfmMepLbrBadMsdu dot1agCfmMepUnexpLtrIn OmniSwitch 6250 CLI Reference Guide November 2009 page 25-55...
Port Status Commands efm-oam port status efm-oam port mode efm-oam port propagate-events Port Event Notification efm-oam errored-frame Commands efm-oam errored-frame-period efm-oam errored-frame-seconds-summary Timer Interval Commands efm-oam port keepalive-interval efm-oam port hello-interval OmniSwitch 6250 CLI Reference Guide November 2009 page 26-1...
Configures the LINK OAM mode on the port or on the range of ports to active or passive. show efm-oam configuration Displays the global LINK OAM configuration. MIB Objects alaDot3OamStatus OmniSwitch 6250 CLI Reference Guide November 2009 page 26-3...
-> efm-oam port 1/1 status enable -> efm-oam port 1/1 status disable -> efm-oam port 2/1-10 status enable -> efm-oam port 2/1-4 status disable Release History Release 6.6.1; command was introduced. page 26-4 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 973
OAM mode, opera- tional status and loopback status of the port. show efm-oam port detail Displays the configuration and other related parameters for a port. MIB Objects dot3OamTable dot3OamAdminState OmniSwitch 6250 CLI Reference Guide November 2009 page 26-5...
-> efm-oam port 1/1 mode active -> efm-oam port 1/1 mode passive -> efm-oam port 2/1-10 mode active -> efm-oam port 2/1-4 mode passive Release History Release 6.6.1; command was introduced. page 26-6 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 975
OAM mode, opera- tional status and loopback status of the port. show efm-oam configuration Displays the global LINK OAM configuration. MIB Objects dot3OamTable dot3OamMode OmniSwitch 6250 CLI Reference Guide November 2009 page 26-7...
Configures the time interval (in seconds) by which the information OAMPDUs are transmitted out of a LINK OAM enabled port. show efm-oam port detail Displays the configuration and other related parameters for a port. MIB Objects alaDot3OamTable alaDot3OamKeepAliveInterval page 26-8 OmniSwitch 6250 CLI Reference Guide November 2009...
On a given port, hello interval time period should not be more than half of keep alive timer on the peer port. Examples -> efm-oam port 1/1 hello-interval 5 -> efm-oam port 2/1-10 hello-interval 10 Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 26-9...
Page 978
Displays the configuration and other related parameters for a port. MIB Objects alaDot3OamTable alaDot3OamHelloInterval page 26-10 OmniSwitch 6250 CLI Reference Guide November 2009...
-> efm-oam port 1/1 remote-loopback process -> efm-oam port 1/1 remote-loopback ignore -> efm-oam port 2/1-10 remote-loopback process -> efm-oam port 2/1-4 remote-loopback ignore Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 26-11...
Page 980
Displays the LINK OAM configuration and other related parame- ters for a port. show efm-oam port remote Displays the configuration and details of the related parameters of detail the remote port. MIB Objects dot3OamLoopbackTable dot3OamLoopbackIgnoreRx page 26-12 OmniSwitch 6250 CLI Reference Guide November 2009...
CLI, an error will be displayed at the CLI prompt. Examples -> efm-oam port 1/1 remote-loopback start -> efm-oam port 1/1 remote-loopback stop Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 26-13...
Page 982
Displays the configuration and details of the related parameters of detail the remote port. show efm-oam configuration Displays the global LINK OAM configuration. MIB Objects dot3OamLoopbackTable dot3OamLoopbackStatus page 26-14 OmniSwitch 6250 CLI Reference Guide November 2009...
Examples -> efm-oam port 1/1 propagate-events critical-event enable -> efm-oam port 1/1 propagate-events critical-event disable -> efm-oam port 2/1-10 propagate-events dying-gasp enable -> efm-oam port 2/1-4 propagate-events dying-gasp disable OmniSwitch 6250 CLI Reference Guide November 2009 page 26-15...
Page 984
Displays the configuration and details of the related parameters of detail the remote port. show efm-oam port statistics Displays the LINK OAM statistics on a port, or a range of ports or on all ports. MIB Objects dot3OamEventConfigTable dot3OamDyingGaspEnable dot3OamCriticalEventEnable page 26-16 OmniSwitch 6250 CLI Reference Guide November 2009...
-> efm-oam port 1/1 errored-frame threshold 10 window 32 notify enable -> efm-oam port 1/1 errored-frame notify disable -> efm-oam port 2/1-4 errored-frame threshold 10 window 32 notify enable -> efm-oam port 2/1-2 errored-frame notify disable OmniSwitch 6250 CLI Reference Guide November 2009 page 26-19...
Page 988
Displays the LINK OAM statistics on a port, or a range of ports or on all ports. MIB Objects dot3OamEventConfigTable dot3OamErrFrameWindow dot3OamErrFrameThreshold dot3OamErrFrameEvNotifEnable page 26-20 OmniSwitch 6250 CLI Reference Guide November 2009...
-> efm-oam port 1/1 errored-frame-seconds-summary threshold 1 window 700 notify enable -> efm-oam port 1/1 errored-frame-seconds-summary notify disable -> efm-oam port 2/1-4 errored-frame-seconds-summary threshold 1 window 700 notify enable -> efm-oam port 2/1-2 errored-frame-seconds-summary notify disable OmniSwitch 6250 CLI Reference Guide November 2009 page 26-21...
Page 990
Displays the LINK OAM statistics on a port, or a range of ports or on all ports. MIB Objects dot3OamEventConfigTable dot3OamErrFrameSecsSummaryWindow dot3OamErrFrameSecsSummaryThreshold dot3OamErrFrameSecsEvNotifEnable page 26-22 OmniSwitch 6250 CLI Reference Guide November 2009...
Related Commands show efm-oam configuration Displays the global LINK OAM configuration. show efm-oam port remote Displays the configuration and details of the related parameters of detail the remote port. MIB Objects alaDot3OamMultiplePduCount OmniSwitch 6250 CLI Reference Guide November 2009 page 26-23...
-> efm-oam port 1/15 l1-ping num-frames 5 delay 100 start -> efm-oam port 1/15 l1-ping num-frames 4 delay 200 start -> efm-oam port 1/5 l1-ping num-frames 100 delay 300 start Release History Release 6.6.1; command was introduced. page 26-24 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 993
Displays the LINK OAM statistics on a port, or a range of ports or on all ports. MIB Objects alaDot3OamLoopbackTable alaDot3OamPortL1PingFramesConf alaDot3OamPortL1PingFramesDelay alaDot3OamPortL1PingStatus alaDot3OamPortL1PingFramesSent alaDot3OamPortL1PingFramesReceived alaDot3OamPortL1PingAverageRoundTripDelay OmniSwitch 6250 CLI Reference Guide November 2009 page 26-25...
Enables or disables the LINK OAM protocol on the switch. show efm-oam port detail Displays the LINK OAM configuration and other related parame- ters for a port. MIB Objects alaDot3OamStatus alaDot3OamMultiplePduCount page 26-26 OmniSwitch 6250 CLI Reference Guide November 2009...
-> show efm-oam port 1/1-5 Port EFM-OAM Status Mode Operational Status Loopback Status -------+----------------+---------+-------------------+---------------- enabled active operational remoteLoopback disabled active activeSendLocal noLoopback enabled passive activeSendLocal noLoopback OmniSwitch 6250 CLI Reference Guide November 2009 page 26-27...
Page 996
The state of the EFM-OAM. LINK OAM instance can have any of the following status. • Enabled : Specifies that the LINK OAM is disabled on the interface. • Disabled : Specifies that the LINK OAM is disabled on the interface. page 26-28 OmniSwitch 6250 CLI Reference Guide November 2009...
Page 997
The state of remote loopback. It can be initiatingLoopback, terminat- ingLoopback, localLoopback, remoteLoopback, noLoopback, or unknown. Mode The state of LINK OAM mode, active or passive. Release History Release 6.6.1; command was introduced. OmniSwitch 6250 CLI Reference Guide November 2009 page 26-29...
Page 998
PDU will be transmitted that many times towards the peer. MIB Objects dot3OamTable dot3OamAdminState dot3OamMode dot3OamOperStatus dot3OamLoopbackTable dot3OamLoopbackStatus page 26-30 OmniSwitch 6250 CLI Reference Guide November 2009...
Output fields are described here: output definitions OAM Status The state of LINK OAM on the port. Operational Status The state of the port in discovering whether the peer has LINK OAM capability or not. OmniSwitch 6250 CLI Reference Guide November 2009 page 26-31...
Page 1000
Displays the status of LINK OAM on all the ports in the system, along with other relevant information like OAM mode, operational status and loopback status of the port. MIB Objects dot3OamTable dot3OamAdminState dot3OamOperStatus dot3OamMode dot3OamMaxOamPduSize dot3OamConfigRevision dot3OamFunctionsSupported alaDot3OamTable alaDot3OamKeepAliveInterval alaDot3OamHelloInterval dot3OamLoopbackTable dot3OamLoopbackStatus page 26-32 OmniSwitch 6250 CLI Reference Guide November 2009...