Panasonic UF-5500 Service Manual page 95

No. Parameter
017 TX START
018 RX START
019 ITU-T V.34
020 ITU-T ECM
021 EP TONE
022 SIGNAL INTERVAL 1 = 100 ms
023 TCF CHECK
024 CED FREQUENCY
025 COMM. START-UP
026 NON-STANDARD
027 SHORT
PROTOCOL B
028 SHORT
PROTOCOL D
029 REMOTE
DIAGNOSTICS
030 CED & 300 bps
031 RTC = EOLx12
032 V34 TX START
033 V34 RX START
034 V34 TX Symbol
Rate
035 V34 RX Symbol
Rate
Function Parameter Table
Selections
1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps
1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps
1 = Off
2 = On
3 = Select
1 = Off (Invalid)
2 = On (Valid)
1 = Off (without EP Tone)
2 = On (with EP Tone)
2 = 200 ms
3 = 500 ms
1 = Normal (Short)
2 = Long
1 = 1080 Hz (non ITU-T)
2 = 2100 Hz
1 = 1'st response
2 = 2'nd response
1 = Off (Invalid)
2 = On (Valid)
1 = Off (Invalid)
2 = On (Valid)
1 = Off (Invalid)
2 = On (Valid)
1 = Off (will not accept)
2 = On (accepts)
1 = 75 ms
2 = 1 sec
1 = Off (EOLx6)
2 = On (EOLx12)
2400-33600bps
2400-33600bps
2400-3429sr
2400-3429sr
Selects the transmission modem start speed, 14400/12000/
TC9600/TC7200/9600/7200/4800/2400 bps.
Note:
This parameter is applicable only when communicating with
regular G3 machines. When communicating with Super G3
(V.34) machines,
use Parameter No. 32.
Selects the reception modem start speed, 14400/12000/TC9600/
TC7200/9600/7200/4800/2400 bps.
Note:
This parameter is applicable only when communicating with
regular G3 machines. When communicating with Super G3
(V.34) machines,
use Parameter No. 33.
Selects whether the ITU-T V.34 is Off, On or Select.
Select: Select whether the ITU-T V.34 is Off or On, when
entering Phone Book Dialing Numbers or Manual
Number Dialing.
Select the ECM mode.
Note:
When communicating with V.34, the ECM mode becomes
effective automatically regardless of this parameter setting.
Selects whether to add the echo protect tone on V.29 mode.
(Used when Echo Suppression is disabled.)
On : Add
Off : Do not add
Selects the time interval between the receiving signal and the
transmitting signal.
Selects the TCF check interval Long/Short
Selects the CED frequency 2100/1080 Hz
Selects the communication start-up condition (XMT and Polling).
(Used when Echo Suppression is disabled.)
Selects own mode (Panafax mode).
Selects the short protocol mode.
Selects the short protocol mode. When activated, it allows the
machine to automatically store the modem speed for each Auto
Dial Number.
Selects whether the machine accepts Remote Diagnostics from
the service station.
Selects the pause interval between the CED and the 300 bps
signal.
(Used when Echo Suppression is disabled.)
Selects the RTC signal, EOLx6 or EOLx12.
Selects the transmission modem start speed for V.34
communication, 33600-2400 bps.
Selects the receiving modem start speed for V.34
communication, 33600-2400 bps.
Selects the transmission symbol rate for V.34, 3429/ 3200/3000/
2800/2400 sr.
Press "V" or "/\ " to select the symbol rate.
Selects receiving symbol rate for V.34, 3429/3429/3200/3000/
2800/2400 sr.
Press "V" or "/\ " to select the symbol rate.
95
UF-5500 / 4500
Function