Panasonic UF-5500 Service Manual page 159

Code Mode Phase
421 RCV B
422 XMT B
427 G3 B
RCV
434 XMT or RCV B
436 G3 RX C
456 RCV B
490 RCV C
494 RCV C
495 XMT C
RCV
501 XMT/ B
RCV(V.34)
502 XMT/ B, C, D
RCV(V.34)
503 XMT/ B, C, D
RCV(V.34)
504 XMT/V.34 B
(Polling)
505 XMT/V.34 B
(Polling)
540 XMT ECM B
541 XMT ECM D
542 XMT ECM D
543 XMT ECM D
544 XMT ECM D
550 RCV ECM C
554 RCV ECM D
580 XMT B
623 XMT A
630 XMT or RCV B
(Polling)
631 XMT A
Fax Information Codes
Description of Problem
Busy Tone is detected after sending NSF
Signal.
Content of NSF (or DIS) or NSC (or DTC)
was invalid.
DCN received to NSF/CSI/DIS transmitted. The interface is incompatible.
CD (response from Modem) did not turn
OFF within 180 sec. after receiver detected
FLAG signal.
DCN received after transmitting FTT.
Received relay transfer request or confi-
dential document to distribute to an end
receiving station or all confidential mail-
boxes are used.
Sum of error lines exceeded the limit (Func-
tion Parameter No. 70) of 64 lines.
Interval between two EOLs was more than
10 sec. when receiver received message
data.
During reception, CD turned OFF or contin-
ued ON for long time. During communica-
tion, lost loop - current.
Remote unit does not have compatible
Modem.
During reception, CD turned OFF or contin-
ued ON for long time. During communica-
tion, lost loop - current.
CS of modem is not able to turn ON during
training.
Polling is rejected from the remote station.
Polling XMT is rejected.
No response after transmitting 3rd CTC or
DCN received.
No response after transmitting 3rd EOR or
received DCN.
No response to the 3rd RR transmitted or
received DCN.
T5 timer (60 sec.) elapsed without MCF.
Stopped Transmission after EOR Transmis-
sion.
Timer between frames in phase C has
elapsed.
Transmitted ERR after receiving EOR.
Sub-address transmission to a unit that has
their DIS bit 49 (NSF bit 155) OFF.
No original was in the ADF. (Built-in dialer
engaged)
Redial count over.
"STOP" button was pressed during Auto
Dialing.
159
Cause
Remote station disconnected the line.
Wrong number is dialed.
There is an incompatibility.
Remote unit is defective.
MAIN PCB is defective.
Transmitter is defective or incompatible.
Line quality is poor.
Line quality is poor.
MAIN PCB is defective.
Transmitter is defective.
Line quality is poor. (EOL is damaged due to line
noise)
MAIN PCB is defective.
Line is disconnected.
Transmitter is defective.
MAIN PCB is defective.
Line is disconnected.
Transmitter is defective.
MAIN PCB is defective.
MAIN PCB is defective.
Line is disconnected.
No polling original is set.
No polling original is set.
Incompatible interface.
Line is faulty.
MAIN PCB is abnormal.
Remote unit is abnormal.
Remote unit is abnormal.
Line is faulty.
MAIN PCB is abnormal.
Defective remote station.
Line is faulty.
Sub-address transmission to a unit that has no
Sub-address function.
Operator removed the original from the ADF
after dialing was completed.
Original was not set properly in the ADF.
No dial tone detected. Sensor dial tone is not
detected. (destination dependent) Busy tone is
detected. (destination dependent) T1 timer (35
± 5 sec.) elapsed without a signal from the
receiver.
UF-5500 / 4500