Panasonic UF-5500 Service Manual page 91

Setting
No. Parameter
Number
125 CONFIRMS STNS
133 JOB BUILD
135 JUNK FAX FILTER
01. JUNK FAX FILTER
02. RCV WITHOUT ID
03. RECEIVED ID
04. ID NO. REGIST.
136 RESTRICT D. DIAL
137 RE-ENTER D. DIAL
142 LAN PC-FAX
156 PRT FORWARD DOC
169 DHCP CLIENT
Setting
1 INVALID Set whether to confirm the destinations.
When set to Valid the document cannot be sent unless the destination is confirmed.
2 VALID
This function also operates when the addresses are specified with Group Dialing or Pro-
gram Dialing function. If an address has been altered (added or removed) when con-
firming addresses, the address confirmation message will appears again when
transmitting the documents (pressing the start key).
1 OFF Selecting whether the machine performs Job Build when the total number of documents
exceeds the maximum capacity of the ADF, or when scanning the documents manually
2 ON
one at a time. If you place the documents on the ADF within 5 seconds after the ADF
scan, the ADF scan will continue for the current scan. (Maximum number of scanning
sheets is 255 pages for one job.)
The Quick Memory Transmission feature (Fax Parameter No. 82) is not available when
the Job Build is set to "2:ON".
Up to 250 pages can be stored. When the number of pages exceeds 255, the memory
overfull message will be displayed. Select "Yes" to start transmitting, or "No" to cancel.
If no action is taken within 5 seconds, the machine will start transmitting the stored orig-
inals.
Function to prevent direct mail FAX and unnecessary FAX messages.
When set to "VALID", the machine will not receive the faxes from the senders whose
numeric ID has been registered as a junk fax number. The denied number IDs can be
1 INVALID
registered in "04.ID NO. REGIST.".
2 VALID
When set to "VALID", the machine will receive faxes from senders without numeric ID
registered.
1 INVALID
(This setting is available only when "01. JUNK FAX FILTER" is set to "VALID".)
2 VALID
When set to "VALID", the sender's numeric ID and received time are printed at the bot-
PRINT tom of the received faxes. If the sender's numeric ID is not registered, only the received
time is printed. (This setting is available only when "01. JUNK FAX FILTER" is set to
1 INVALID
"VALID".)
2 VALID
Register fax numbers as junk fax number.
(NO. 01-30) Up to 30 fax numbers can be registered for junk fax number. (Including numerals "0-9",
blank space, and +symbol.) (When comparing the sender's numeric ID to the registered
junk fax numbers, blank spaces between numbers are ignored.)
1 INVALID Enable or disable the Restrict Direct Dial function.
When set to "VALID", manual input destination Tel No. and "Redial" button are not
2 VALID
accepted.
1 INVALID Used to set whether to display the address reinsert screen when indicating the address
for direct dial, inputting the mail address for Internet FAX, redialing or inputting the
2 VALID
address for confirming the address. When set to "VALID", unit will require input destina-
tion Tel No. or Mail address twice for confirmation. Unit will proceed transmit job when
destination data is matched.
This setting is not available when the Restrict Direct Dial function is set to "VALID".
1 INVALID Selecting whether the machine accepts and performs G3 relayed transmission. (Relay
Station Functions)
2 VALID
(UF-5500 only)
1 INC. ONLY Selecting whether a fax received in memory to be forwarded is always printed or only
when forwarding is incomplete.
2 ALWAYS
1 INVALID Select whether the machine would automatically acquire the Network Parameters from
the DHCP Server. (Such as IP Address, Subnet Mask, Default Gateway IP Address,
2 VALID
etc.) (UF-5500 only)
Note: If you change the setting of this parameter, the machine will reboot automatically.
Comments
91
UF-5500 / 4500