Pioneer PRV-LX10 Service Manual page 191

5
No. Name
10
PLAY button ( )
11
PAUSE button ( )
12 REC button ( )
13 PLAY/REC indicator for DVD 2 drive
14 DISC indicator for DVD 2 drive
15 EJECT button ( ) for DVD 2 drive
16
MOUSE/KEYBOARD connectors
17 STEP FWD button ( )
18 STEP REV button ( )
19
SCAN/SKIP FWD button (
20
SCAN/SKIP REV button (
21
ENTER button
22 CURSOR buttons ( ,
23 Filter cover (2)
24 FUNCTION button (*4)
25
DISPLAY button
26
Remote control sensor
27
VOLUME knob
28
PHONES jack
*1 A disc created on the PRV-LX10 or PRV-LX1 that contains many titles may take dozens of seconds to recognize when
loaded. The DISC indicator flashes and the disc recording and playback cannot be started during disc recognition.
*2 Progressive is supported only during NTSC output.
• Connect to progressive-scan TV monitor. Non-progressive monitors will not produce correct playback.
• When progressive is set to ON, no video is output to any output connectors except the component output.
*3 Functionality of connected devices is not guaranteed. If USB mouse and keyboard operation is unstable, try disconnecting
and reconnecting the USB connector. If a USB hard disk drive is not recognized, or if operation is unstable, change to a
hub supporting USB 2.0. If operation continues to be erratic, inquire your Pioneer dealer or one of the service centers
listed at the end of this manual.
*4 This operates the same as the remote control unit's SETUP button. The FUNCTION button operates only in the idling
condition.
*5 When performing reverse slow-motion playback with progressive output (NTSC only), the speed cannot be changed.
5
6
When this button is pressed, playback begins from selected source (DVD
drive or HDD), and the indicator lights (white). When HDD is designated
as the recording destination and time shift playback has been set, this
button responds even during recording, and initiates playback from the
recording start.
When pressed, recording or playback is temporarily interrupted and the
indicator lights (white). During recording, allows automatic setting of
chapters. To resume recording from the recording pause mode, press the
REC button.
When pressed, recording begins to the selected recording destination
(drive or project), and the indicator lights (white).
Lights to indicate operating state of DVD2 drive.
Appears green during PLAY mode, and orange during REC mode.
Located to the right side of DVD2, this indicator light (orange) to indicate
that a disc is loaded. (*1)
Press to open/close DVD2 disc tray. The DISC indicator flashes from the
time the button is pressed until the disc tray closes fully.
Allows connection of a USB mouse, USB keyboard and USB HDD to the unit. (*3)
During normal playback, press for frame advance. Hold depressed for
slow motion playback; during slow mode, press again to increase
playback speed. (*5)
During normal playback, press for frame playback in reverse direction.
Hold depressed for slow motion playback; during slow mode, press to
decrease playback speed. (*5)
During playback, press to move to next title or chapter. Hold depressed to
/ )
initiate scan mode.
During playback, press to move to previous title or chapter. Hold
/ )
depressed to initiate scan mode.
Press to select function menu items and commands, and to input DVD
menu items and commands (during DVD playback).
During recording, press to insert chapter marks at optional locations.
Use when selecting function menu items, and for DVD menu control
, , )
(during DVD playback).
These are ventilation ports provided to prevent excessive heating of
internal parts. During installation and operation, do not allow these ports
to become blocked, since malfunctions may result.
* Air filters are installed inside these filter covers, and must be removed
and replaced at regular intervals. Continuing to use the unit with clogged
filters may result in malfunction. Consult the appended instruction sheet
"Air Filter Replacement Instructions and Precautions".
Press to enable and disable the monitor's on-screen function menu
display (default setting: DISABLED). When disabled, the unit returns to
idling condition.
Press to turn on-screen display (OSD) ON/OFF (default setting: OFF). This
button does not operate when on-screen function display is set to
DISABLED.
Receives signals from the remote control unit. Do not allow this part to be
blocked by other objects.
Use to adjust output level to the headphones jack.
Use to connect headphones.
PRV-LX10
6
7
Function
7
8
A
B
C
D
E
F
191
8