Pioneer PRV-LX10 Service Manual page 178

1
XC2S100-5PQ208C (PCIB ASSY : IC2309)
• PCIF XILINX
A
Pin Function
No. Pin Name I/O
−
1 GND Ground
−
2 N.C. Not used
3 AD28 I/O PCI address/data
4 AD27 I/O PCI address/data
5 AD26 I/O PCI address/data
6 AD25 I/O PCI address/data
7 AD24 I/O PCI address/data
B
8 CBE3 I/O PCI bus command / byte enable
9 IDSE I PCI initialization device select
10 AD23 I/O PCI address/data
−
11 GND Ground
−
12 VccO I/O power supply (3.3V)
−
13 Vccint Core power supply (2.5V)
14 AD22 I/O PCI address/data
15 AD21 I/O PCI address/data
16 AD20 I/O PCI address/data
17 AD19 I/O PCI address/data
C
18 AD18 I/O PCI address/data
−
19 GND Ground
20 AD17 I/O PCI address/data
21 AD16 I/O PCI address/data
22 CBE2 I/O PCI bus command / byte enable
23 FRM I/O PCI frame
24 IRDY I/O PCI initiator ready
−
25 GND Ground
−
26 VccO I/O power supply (3.3V)
27 TRDY I/O PCI target ready
D
−
28 Vccint Core power supply (2.5V)
29 DEV I/O PCI device select
30 PAR I/O PCI parity
31 CBE1 I/O PCI bus command / byte enable
−
32 GND Ground
33 AD15 I/O PCI address/data
34 AD14 I/O PCI address/data
35 AD13 I/O PCI address/data
36 AD12 I/O PCI address/data
37 AD11 I/O PCI address/data
E
−
38 Vccint Core power supply (2.5V)
−
39 VccO I/O power supply (3.3V)
−
40 GND Ground
41 AD10 I/O PCI address/data
42 AD09 I/O PCI address/data
43 AD08 I/O PCI address/data
44 CBE0 I/O PCI bus command / byte enable
45 AD07 I/O PCI address/data
F
178
1
2
Pin Function No. Pin Name I/O
PRV-LX10
2
3
46 AD06 I/O PCI address/data
47 AD05 I/O PCI address/data
48 AD04 I/O PCI address/data
49 AD03 I/O PCI address/data
50 M1 I Configuration mode switch fixed to H
−
51 GND Ground
52 M0 I Configuration mode switch fixed to L
−
53 VccO I/O power supply (3.3V)
54 M2 I Configuration mode switch fixed to H
−
55 N.C. Not used
−
56 N.C. Not used
57 AD02 I/O PCI address/data
58 AD01 I/O PCI address/data
59 AD00 I/O PCI address/data
−
60 N.C. Not used
Signal for LTC_SW (Xilinx) configuration
61 XBSOUT O
62 WE0 I SH write strobe
−
63 N.C. Not used
−
64 GND Ground
−
65 VccO I/O power supply (3.3V)
−
66 Vccint Core power supply (2.5V)
−
67 BREQ Not used
−
68 BACK Not used
69 CASL I CAS for SH SDRAM
70 RAS3 I RAS for SH SDRAM
71 CKE I CKE for SH SDRAM
−
72 GND Ground
73 CS3 I SH chip select 3
74 RDWR I SH read/write
75 WE3 I SH write strobe
−
76 Vccint Core power supply (2.5V)
−
77 I.GCK1 Not used
78 Vcc0 I SH write strobe
−
79 GND Ground
80 I.GCK0 I SH system clock (40 MHz)
81 WE2 I SH write strobe
82 WE1 I SH write strobe
83 DRQ1 0 DMA REQ for SH
84 DAC1 I DMA ACK for SH
−
85 GND Ground
86 A15 I SH address bus
87 A14 I SH address bus
88 A13 I SH address bus
89 A12 I SH address bus
90 A11 I SH address bus
3
4
Pin Function
4