Pioneer PRV-LX10 Service Manual page 119

5
2-6) Clearing data on cumulative power-on time, etc. ( [A.MON] - [0] , [1] , [7], [8] , [9] )
After entering Test mode, press the [A.MON] key to enter Test mode for clearing data on cumulative power-on time, etc.:
[0]: Clearing cumulative time for accessing to the HDD
[1]: Clearing cumulative power-on time of the product (Cumulative time of accessing the HDD is not cleared.)
[7]: Preparing to download the Setup file (obtainable via FTP for users)
[8]: Copying the Setup file (obtainable via FTP for users)
[9]: Copying the Log file (obtainable via FTP for users)
2-7) Error-Rate-Measurement Test mode ( [PLAY] )
After entering Test mode, insert a disc and press the [PLAY] key to enter Error-Rate-Measurement Test mode for Drive 1.
For measurement for Drive 2, press the [2] key. Measurement starts from address 0. To change the address for measurement, use [SCAN F]
or [SCAN R].
[SCAN F]: Advancing the address for measurement by 0x10000
[SCAN R]: Setting the address for measurement back by 0x10000
[1]: Starting measurement for Drive 1
[2]: Starting measurement for Drive 2
[OP/ST]: Terminating measurement
2-8) Test mode with result (OK/NG) displayed ( [0] , [1] to [7] )
After entering Test mode, press one of the numeric keys. The corresponding test will be performed and the result (OK/NG) is displayed.
To proceed to the next test and clear the OK/NG result, press the [CLEAR] key.
[0]: Consecutive testing of [1] - [4] below (Testing stops when the test result becomes NG.)
[1]: RS-422A Loopback Test
Perform this test after connecting the IN and OUT RS-422A ports with a cable.
[1]: RS-232C Loopback Test
Perform this test after connecting the jig for loopback testing to the RS-232C port.
[3]: LAN Test
Perform this test after connecting the unit to the valid network with a LAN cable.
[4]: USB Test
Perform this test after connecting keyboards or mice to all the USB ports on the front and rear panels.
[5]: Error Rate Test (Drive 1)
Perform this test after loading a disc into Drive 1.
[6]: Error Rate Test (Drive 2)
Perform this test after loading a disc into Drive 2.
[7]: LTC display
The LTC being input is displayed on the FL display. In this mode, OK/NG judgment is not performed.
[CLEAR]: (When entered after one of the above test) To clear the result display
Note: About error-rate measurement, see the note on it in "7.1.2 List of Codes in Test Mode."
2-9) How to copy the Setup file to another PRV-LX10
1 On a PRV-LX10 (hereinafter referred to as the PRV-LX10(S)) whose Setup file is to be copied, execute the command for copying the
Setup file in Test mode for clearing data on cumulative power-on time, etc. ([ESC]-[TEST]-[A.MON]-[8]). See "2-6 Clearing data on
cumulative power-on time, etc.".
2 With a PC that is connected with the PRV-LX10(S) through a network, log in on the FTP server as described in the instruction manual
(User name: PRVUser, password: prv-lx1). Then copy the Setup file (system.xml) from the first-layer directory.
3 Connect the PRV-LX10 (hereinafter referred to as the PRV-LX10(D)) that will receive the copied Setup file with the PC used in Step 2
above, through a network. Then log in on the FTP server (User name: PRVUser, password: prv-lx1) in the same way as in Step 2.
Move the Setup file copied in Step 2 to the first-layer directory of the FTP server.
4 Execute the command for preparing for downloading the Setup file in Test mode for clearing data on cumulative power-on time, etc.
([ESC]-[TEST]-[A.MON]-[7]). See "2-6 Clearing data on cumulative power-on time, etc.".
5 Turn off the power to the PRV-LX10(D).
6 Turn on the power to the PRV-LX10(D) again. The new Setup file will be applied.
5
6
PRV-LX10
6
7
7
8
A
B
C
D
E
F
119
8