Pioneer PRV-LX10 Service Manual page 171

5
No. Pin Name
41 LD_SB
42 LD_ON
43 LD_REC
44 SIF
45 SOF
46 CKF
47 LD_DRV1
48 LD_DRV2
49 LD_HDD
DRV1_LD_ACCESS (GREEN)
50
DRV1_LD_ACCESS (RED)
51
52 LD_STOP
53 DRV2_DISC
DRV2_LD_ACCESS (RED)
54
55 PON
56 RSTBTN
57 PS_ON_O#
58 PWR_SW#
59 RESET#
60 XRESET
61 IRIN
62 FAN_CONT1
63 FAN_CONT2
64 FAN_CONT3
65 PWR_SW2#
66 P05/INTP5
67 VSS0
68 VDD1
69 X2
70 X1
71 VPP
72 XT2
73 XT1/P07
74 VDD0
75 AVREF0
UP,DOWN,LEFT,RIGHT
76
77 REGION
78 K_SCAN_STEP
ENTER,SETUP,DISPLAY
79
80 SIMUKE1
5
6
I/O
O STANDBY/ON LED control H: Normally (Extinguish), L: Light
O STANDBY/ON LED control H: Normally (Extinguish), L: Light
O REC LED control H: Normally (Extinguish), L: Light
I SIF (for flash writing)
O SOF (for flash writing)
I CKF (for flash writing)
O DRIVE 1 LED control of drive select LED H: Normally (Extinguish), L: Light
O DRIVE 2 LED control of drive select LED H: Normally (Extinguish), L: Light
O HDD LED control of drive select LED H: Normally (Extinguish), L: Light
O Access LED (GREEN) control of DRIVE 1 H: Normally (Extinguish), L: Light
O Access LED (RED) control of DRIVE 1 H: Normally (Extinguish), L: Light
O STOP LED control H: Normally (Extinguish), L: Light
O Disc existence of DRIVE 2: No DISC (Extinguish), L: DISC exists (Light)
O Access LED (RED) control of DRIVE 2 H: Normally (Extinguish), L: Light
I STANDBY/ON key (S509) check H: PUSH, L: Normally
I Not used
O Output the PS_ON signal which received from the Mother Board to the ATX power
O
Output a relay control signal for supply +5VSB to the Mother Board
O Reset output H: Normally, L: Reset
I For flash writing
I Remote control signal receive
O FAN control for the rear
O FAN control for the DRIVE 1
O FAN control for the DRIVE 2
O Power SW signal to the Mother Board H: Normally, L: PUSH
−
Not used
−
Not used
−
Power supply 5V
−
Crystal connection pin for clock oscillation
I Crystal connection pin for clock oscillation (input)
−
Vpp (for flash writing)
−
Not used
−
Not used
I Power supply 5V
I AVref0 5V
I Analog input UP: 4.25V, DOWN: 2.8V, LEFT: 1.24V, RIGHT: 0V
I Destination setting R
Analog input SCAN/SKIP_FWD: 4.25V, SCAN/SKIP_REV: 2.8V, STEP_FWD: 1.24V, STEP_REV: 0V
I
I Analog input ENTER: 4.25V, FUNCTION: 2.8V, DISPLAY: 1.24V
I Destination setting S0
6
7
Pin Function
PRV-LX10
7
8
A
B
C
D
E
F
171
8