Pioneer PRV-LX10 Service Manual page 121

5
No. Code Input
53 [4]
54 [5]
55 [6]
56 [7]
57
58 [ESC]
59 [ESC+[PAUSE]
60 [1]
61 [2]
62 [3]
63 [4]
64 [5]
65 [6]
66 [7]
67 [8]
68 [9]
69 [0]
70 [+10]
71 [TEST]
72 [CX]
73 [REP.A]
74 [REP.B]
75 [STEREO]
76 [P.RUN]
77 [A.MON]
78 [SPEED-]
79 [SPEED+]
80 [SIDE.A]
81 [SIDE.B]
82 [TV/LDP]
83 [SCAN.F]
84 [SCAN.R]
85 [x3 FWD]
86 [x3 REV]
87 [STEP F]
88 [STEP R]
89 [ESC]+[OPEN/STOP]
90 [ESC+[DISP]
91 [DISP]
÷ How the [ESC] code is processed
• When the [ESC] code is received, ESCAPE mode is entered, but in
combination with the code(s) that follow(s), a specific meaning is added.
• ESCAPE mode is canceled if another code is received after the [ESC]
code.
• If [ESC] codes are received continuously, ESCAPE mode is retained.
÷ For playback-related operations, use the remote control unit supplied with
the main unit.
5
6
Operation/Usage
USB TEST
Error Rate TEST (Drive 1)
Error Rate TEST (Drive 2)
LTC display
[CLEAR] Terminating result display
Canceling Test mode
Shortcut command
V IN- Composite
V IN-S
V IN-Component (Beta)
V IN-Component (SMPTE)
V IN-DV
V IN-SDI
A IN-RCA
A IN-XLR
A IN-DV
A IN-SDI
A IN-AES/EBU
Target DRV - HDD
Target DRV - DVD 1
Target DRV - DVD 2
Target DRV - DVD 1 & 2
External Sync. OFF
External Sync. NTSC
External Sync. PAL
Progressive OFF
Progressive ON
TC PORT - LTC
TC PORT - RS-422A
TC PORT - DV
DV OUT ON
DV OUT OFF
REC
REC STOP
Initialize
Finalize
Open/Close
Display of data for debugging-Page 1: System data
To next page
PRV-LX10
6
7
USB devices must be connected to four ports.
Do not operate the connected USB devices
during the USB test. For example, if the
connected mouse is operated during the USB
test, the unit may hang up.
The error rate is measured at 0x30000 three times, and the
average value is judged. The command must be input during
playback stop.
ROM
R, RW
Effective when an optional drive is mounted
Input TC is displayed on the FL display
Effective when an optional board is mounted
Effective when an optional board is mounted
Effective when an optional board is mounted
Effective when an optional board is mounted
Effective when an optional board is mounted
Effective only during playback or recording stop
Effective only during playback or recording stop
Effective only during playback or recording stop
Effective only during playback or recording stop
Effective only during playback or recording stop
Page 1: DVD-playback-related data,
FAN/PS-ON operation data, destination/region
data (DECB/DRV1/DRV2), GUID data
Page 2: DVD-playback-related data
Page 3: Decoding-related data (DECB)
Page 4: Encoding-related data (PCIB/AVIB)
Page 5: Encoding-related data (APL)
Page 6: Linux-related data
÷ The factory preset mode of the unit at power-on is Standby. To start up the
unit, press the [STOP] button, then press the [STANDBY/ON] button while
in Standby mode.
÷ If the error rate being measured is distinctly degraded because of
scratches on the media or defective media, a command cannot be sent
from the drive, and proper error-rate-measurement may not be performed.
If an error rate is not displayed, or OK/NG is not displayed on the monitor,
restart the PRV-LX10 (by resetting the drive) and perform the error-rate-
measurement again.
7
8
Remarks
Th value 3.3x10E-3
Th value 3.3x10E-3
8
A
B
C
D
E
F
121