How To Install The Os Or Program - Pioneer PRV-LX10 Service Manual

1

7.1.14 HOW TO INSTALL THE OS OR PROGRAM

OS installation
1 While holding the [ENTER] button on the front panel
pressed, press the [STANDBY/ON] button to start the
A
unit.
2 "PGM-INSTALL" is displayed on the FL display, and the
tray for the DVD Drive opens.
Display on the monitor screen:
----------------------------------------
- PRV-LX10 Program Installer -
----------------------------------------
PLEASE INSERT INSTALLATION CD IN DRIVE ONE,
THEN PRESS [ENTER] BUTTON ON FRONT PANEL
FOR 2 SECONDS TO BEGIN UPDATE.
B
>>
3 Load the OS installation disc into the tray then press the
[ENTER] button. The tray will close, and changing of the
BIOS settings starts.
Display on the FL display:
DOWNLOAD FULL
Display on the monitor screen:
========================
C = PRV-LX10 Program Installer =
========================
The PRV-LX10 will automatically start power off
after 5 seconds later.
Please press the power button after power off.
PLEASE WAIT A MINUTE.
Completed changing the BIOS settings.
4 When the unit is automatically turned off, turn it back on.
D
5 If the following menu* appears on the screen, select the
operation you wish. Use the corresponding buttons on
the front panel for selection. (For example, press the
[UP] button to select full installation.)
(1) [UP] : Full Install (Delete all data)
(2) [DOWN] : Install (Keep user's data)
(3) [LEFT] : HDD File System Check
(4) [RIGHT] : HDD Test(Bad Block Check)
(5) [SCAN R] : Quit
E
F
150
1
2
(1) [UP]: Full Install (Delete all data)
• The whole HDD is formatted, then the OS is installed.
• All data, including the user data, are deleted. Installation is
completed in about 10 minutes, then rebooting starts.
• During installation, the progress is displayed on the
screen. If the screen does not change after about 15
minutes, or if the installation process has not been
completed after about 30 minutes, turn off the power and
restart the OS installation process. If installation cannot be
completed on the second try, replace the HDD.
IMPORTANT!: After OS installation, be sure to install
(2) [DOWN]: Install (Keep user's data)
• Only the OS is installed, leaving the user's data intact.
This does not mean, however, that the integrity of the
user's data is guaranteed.
• Installation is completed in about 8 minutes, then
rebooting starts.
• During installation, the progress is displayed on the
screen. If the screen does not change after about 15
minutes, or if the installation process has not been
completed after about 30 minutes, turn off the power and
restart the OS installation process. If installation cannot be
completed on the second try, replace the HDD.
IMPORTANT!: After OS installation, be sure to install
(3) [LEFT]: HDD File System Check
• A logical check of all files on the HDD is performed, then
the results are displayed.
• To return to the menu, press the [ENTER] button on the
front panel.
(4) [RIGHT]: HDD Test (Bad Block Check)
• A physical check of the HDD is performed, then the results
are displayed. It must be noted that this test takes 10
hours or more.
• To return to the menu, press the [ENTER] button on the
front panel.
(5) [SCAN R]: Quit
• To terminate the installation program and start rebooting
*With some installation discs for production lines, full
installation starts automatically, without displaying
the menu.
6 Execute the selected item.
• After execution, rebooting starts automatically.
7 Turn off the power.
8 Start up the unit by pressing the [STANDBY/ON] button
on the front panel, then make sure that the version of the
OS is updated, using the Debug screen (ESC + DISP).
9 Proceed to program installation.
PRV-LX10
2
3
the program.
the program.
3
4
4