Panasonic WV-CS950 Operating Instructions Manual page 31

WV-CS950_US 05.4.27 8:54 PM ページ31
Notes:
• Automatic tracking
horizontal to directly below the camera. The
digital flip function (page 34) does not operate.
Also, the pan range can be limited by using the
PAN LIMIT setting (this page).
• The automatic tracking function incorporated in
this system easily tracks moving objects on
screen. Moving subjects are not automatically
tracked in the following situations.
• When multiple moving subjects are on screen
• When the subjects are moving very fast
• When the subject has little contrast
• When moving objects are either large or small
• When the image is dark
• When the image flickers
Tilting the joystick cycles through settings in the
sequence shown below.
OFF ↔ SEQ ↔ SORT ↔ AUTO PAN ↔ PATROL1 ↔ PATROL2
AUTO TRACK ↔ PATROL4 ↔ PATROL3
Notes:
• The auto mode is exited automatically whenever
manual PAN/TILT or ZOOM/FOCUS is performed if
AUTO PAN is operating and PAN/TILT does SEQ,
SORT, PATROL, or AUTO TRACK movement.
Note, however, that that the contents of the setting
menu do not change. To return to the auto mode,
open the setup menu and then close it again. The
auto mode will also activate when the self return
trigger time (page 30) elapses.
• During operation, the lens may enter the refresh
mode.
• PATROL1-4 displays only the set number of
patrol routines (page 32).
● Configuring AUTO PAN Detailed
Settings
1. Perform the following steps to set the PAN start
point and end point.
(1) Move the cursor to POSITION, press the CAM
(SET) button, and then move the cursor to
START.
(2) Use the joystick to move the camera to the
desired PAN start point, and then press the
CAM (SET) button.
This defines the start point and moves the
cursor to END.
(3) Use the joystick to move the camera to the
desired PAN end point, and then press the CAM
(SET) button.
This defines the start point and moves the
cursor to POSITION.
POSITION
SPEED
ENDLESS
DWELL TIME
PAN LIMIT
RET TOP
covers a range
**AUTO PAN**
START
END
••••I••••
L H
OFF
1S
OFF
2. Move the cursor to SPEED and then tilt the joystick
from left or right to select a panning speed setting.
Shifting the setting towards the "H" (right) side
increases the speed, while shifting towards the "L"
(left) side decreases it.
3. Move the cursor to ENDLESS, and then tilt the joystick
left or right to turn endless panning on or off.
ON : Pans from the start point to the end point,
and then continues to pan in the same
direction from the end point to the start point.
Select OFF for the PAN LIMIT setting (step 5)
when using this setting. Panning will be
repeated endlessly.
OFF : Pans from the start point to the end point,
and then reverses direction to pan from the
end point to the start point. Panning is
repeated endlessly.
4. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select the start point and end
point dwell time setting.
Tilting the joystick cycles through the stop time
display in the sequence shown below. (unit: sec)
0S ↔ 1S ↔ 2S ↔ 3S ↔ 5S ↔ 10S ↔ 20S ↔ 30S
5. Move the cursor to PAN LIMIT, and then tilt the
joystick left or right to toggle it on and off.
ON : Limits manual panning to the zone between the
start point and the end point. The TILT range is
from horizontal to straight down. Select OFF for
the ENDLESS setting (step 3) when using this
setting.
OFF : Allows manual panning outside the zone
between the start point and the end point.
PAN LIMIT
PAN LIMIT allows panning in the area from the start
point to the end point specified in step 1, but not in the
area from the end point to the start point.
End point
AUTO
PAN zone
Notes:
• When the panning, tilting, zooming or focusing
in the SEQ, SORT or PATROL mode is controlled
manually, the auto mode function should be
cancelled.
To activate the auto mode, select the desired
auto mode again or set a time for SELF RETURN
in the SET UP menu.
• When 0S is selected, the camera stops without
dwelling and starts.
• Auto refreshing may be activated during the patrol
play or the auto mode to calibrate the lens position.
-31-
Camera
PAN LIMIT
zone
Start point