Combination Camera Operating Instructions WV-CS850 Model No. WV-CS854 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
Page 2
ENGLISH VERSION Vi erklærer os eneansvarlige for, at dette produkt, som We declare under our sole responsibility that the product to denne deklaration omhandler, er i overensstemmelse med which this declaration relates is in conformity with the stan- den følgende standarder eller andre normative dokumenter dards or other normative documents following the provisions i følge bestemmelserne i direktivene 73/23/EEC og of Directives EEC/73/23 and EEC/89/336.
Auto Mode Setting ......... 21 OPTIONAL ACCESSORIES ......55 APPENDIX ............56 PREFACE Panasonic presents highly advanced CCTV tech- CCD is employed for use under extremely low nology that meets the demands of new and ever- lighting conditions : 0.06 lx for monochrome and changing applications.
PRECAUTIONS 1. Do not attempt to disassemble the cam- 7. If “OVER HEAT” sign appears on the era. monitor screen To prevent electric shock, do not remove The temperature inside the camera exceeds screws or covers. the normal level because of a malfunction of There are no user serviceable parts inside.
Alarm Input Connector y Camera Mounting Base w Alarm Output Connector u Panning Start Point e Video Output Connector i Fall Prevention Wire r Data Port o Decoration Cover t Power Cable for WV-CS850 !0 Dome Cover t* Power Cable for WV-CS854...
SETUP Setup Menu Setup menus are shown in the diagram below. Various kinds of setup are available to have the camera fulfill your requirements. Menus are built in a hierarchical structure from the Setup menu at the top down to Manual Mask Area Selection at the bottom. These menus are described in the following pages for reference prior to setup.
Page 7
Camera RS-485 Menu Setup To A Light WHITE Sensitivity Sync CAMERA ID Shutter Motion AF MODE Control ON/OFF INT/LL Editing Speed Detector Selection ALC/MANUAL ON/OFF Selection ON/OFF Mauual Mauual Mauual Super-D2 Super-D2 CAMERA ID Level Level Mauual Automatic Level Mauual Display Adjustment Adjustment...
Page 8
The keys (switches) to use for setup are as shown in the table below. The joystick on the connected con- troller may also be used for setup. The table also shows the functions versus the operations of the indi- vidual controllers. For further details, see the manual for the controller to be used. The switches and con- trols are abbreviated as SW and CTRL in the table.
Setup Menu Description PRESET (1) Position (POSITION SET) POSITION SET adjusts the camera picture by panning, tilting, zooming and focusing. See page 15 for the setting. (2) Preset Identification (PRESET ID) A preset ID (identification of up to 16 alphanumeric characters) can be displayed on the screen. See page 16 for the setting.
Page 10
AUTO PAN KEY This setting assigns SEQ, SORT, AUTO PAN or PATROL (PLAY) to the AUTO key on the controller. After this setting, the AUTO key performs as assigned. Note: AUTO PAN LED on the controller does not light if other than AUTO PAN is assigned. DIGITAL FLIP ON/OFF Tilt range is limited within 0°...
Page 11
(6) Password Lock ON/OFF (PASSWORD LOCK ON/OFF) This setting controls access to the PRIVACY ZONE to be free or limited. If PASSWORD LOCK ON is selected, the (DIS) follows the PRIVACY ZONE ON or OFF set on the SPECIAL1 menu. (7) Cleaning ON/OFF This is for refreshing the electric-mechanical contacts built in the camera.
Page 12
Generally, when a light from the background is too strong such as a spotlight, all objects except the main object in the picture are displayed darker because the lens iris is adjusted with respect to strong brightness. This model ignores strong brightness by masking the source of the strong bright- ness, thereby main object is displayed clearly.
Page 13
(7) White Balance (WHITE BAL) You can select one of two modes for white balance adjustment as follows: • ATW (Auto Tracing White Balance) In this mode, the colour temperature is monitored continuously and thereby white balance is set automatically. The colour temperature range for the proper white balance is approximately 2 600 - 6 000K.
SETTING PROCEDURES The following setting procedures are described on the assumption that this model is used in combination with the WJ-SX550A matrix switcher and WV-CU550A system controller. In case of using other controller than the WV-CU550A, refer to the table on page 8. Menu Display D4 menu Setup Menu Display...
Preset Setup menu *** SET UP MENU *** Preset Menu Display PRESET 1* HOME POSITION 1. Displaying the preset menu directly SELF RETURN 10MIN (1) Move the cursor to PRESET 1 and move the joystick to the left AUTO MODE AUTO PAN AUTO PAN KEY or right to select the position number to be set.
Page 16
3. Pan Offset PRESET NUMBER SET menu (1-32) If the camera is replaced with a new one, Pan Offset is used to ** PRESET NUMBER SET ** adjust its positions to be the same as before. Preset position data is uploaded by the controller that was once downloaded before the former camera was removed.
Page 17
2. Press the CAM (SET) key to display the preset ID setting menu. To enter a new PRESET ID 1. Move the cursor to the desired character using the joystick, and press the CAM (SET) key. 2. The selected character appears in the editing area. (The pointer in the editing area moves to the right automatically at this moment.) To enter a blank, select SPACE.
Page 18
To set a display position for a PRESET ID PRESET NO. 1* 1. Move the cursor to POSI and press the CAM (SET) key. The 0123456789 ABCDEFGHIJKLM display position set menu appears. NOPQRSTUVWXYZ ().,'":;&#!?= 2. Using the joystick, move the ID to the desired position on the +-*/%$ÄÜÖÆÑÅ...
Page 19
Dwell Time Setting Preset setting menu PRESET NO. 1* • Move the cursor to DWELL TIME and set a dwell time by moving the joystick to the left or right. Dwell time changes as follows: POSITION SET PRESET ID ALC/MANUAL DWELL TIME 1MIN 2MIN...
Deleting Preset Positions Setup menu *** SET UP MENU *** 1. Move the cursor to PRESET 1 and select the position number to PRESET 1* be deleted by moving the joystick. HOME POSITION SELF RETURN 10MIN AUTO MODE AUTO PAN AUTO PAN KEY DIGITAL FLIP LOCAL/REMOTE...
Auto Mode Selection Setup menu *** SET UP MENU *** 1. To set auto mode PRESET 1* Move the cursor to AUTO MODE and select a mode by moving HOME POSITION SELF RETURN 10MIN the joystick to the left or right. Modes change as follows: AUTO MODE AUTO PAN AUTO PAN KEY...
6. To set endless turn ON/OFF ** AUTO PAN ** Move the cursor to ENDLESS, and move the joystick to the left or POSITION SET START right to set endless turn ON or OFF. SPEED ••••|•••• ON: The camera pans from the start position to the end position, PAN LIMIT then keeps rotating in the same direction to return to the start ENDLESS...
LOCAL/REMOTE Setting Setup menu *** SET UP MENU *** • Move the cursor to LOCAL/REMOTE, and move the joystick to the PRESET 1* left or right. HOME POSITION SELF RETURN 10MIN You can toggle between LOCAL and REMOTE. AUTO MODE AUTO PAN AUTO PAN KEY Note: REMOTE does not work when the WV-RM70, WV-CU360 or...
Page 24
3-3 Move the cursor to PUSH SET on the ZOOM/FOCUS, then ZOOM/FOCUS setting menu press the CAM (SET) key. ** ZONE NUMBER 3*/8 ** →PUSH SET PAN/TILT →PUSH SET ZOOM/FOCUS U TILT D/L PAN R ZONE SCALE ••••|•••• SET DEL 3-4 Adjust zoom and focus, then press the CAM (SET) key.
Page 25
Area Title (AREA TITLE) Special 1 menu Up to 8 area titles can be added in specific positions. ** SPECIAL1 ** PRIVACY ZONE ON (DIS) PROPO. P/T AREA TITLE ON (NESW) 1. Select ON (NESW), ON (USER) or OFF by moving the joystick to PATROL PLAY ALARM IN/OUT...
Page 26
Setting [ON (USER)] Special 1 menu If ON (USER) is selected on the SPECIAL1 menu, the Area Title ** SPECIAL1 ** PRIVACY ZONE ON (DIS) selection menu appears. The screen has the number column and PROPO. P/T AREA TITLE ON (USER) title column above RET and RESET.
Page 27
Patrol (PATROL) A routine of manual operations can be stored for up to 30 seconds Special 1 menu and later reproduced repetitively. ** SPECIAL1 ** PRIVACY ZONE ON(ENB) PROPO.P/T PATROL AREA TITLE PATROL PLAY 1. For PATROL LEARN, set the following parameters for the starting ALARM IN/OUT PASSWORD LOCK position.
Page 28
PATROL PLAY with a controller not having PATROL key 1. Close the SET UP or SPECIAL1 menu. The camera turns to the starting point and the operations stored in the memory are reproduced. Iris operation only is accepted during playback. 2.
Page 29
COAXIAL ALARM OUT Alarm output signals are supplied through the coaxial cable. 1. Move the cursor to COAX and select ON or OFF. 2. Press the CAM (SET) key. ON: The camera sends an alarm output signal via the coaxial cable after it turns to a preset position.
Page 30
NEW PASSWORD NEW PASSWORD 4. To change the password in step 3-3 above, move the cursor from NEW PASSWORD? ** 0 1 2 3 4 5 6 7 8 9 OK to NEW PASSWORD then press the CAM (SET) key. NEW PASSWORD menu appears.
Page 31
Electric Zoom ON/OFF (EL-ZOOM ON/OFF) Special 1 menu The electric zoom magnifies a scene tenfold. With a twenty-twofold optical zoom lens, the camera is capable of 220-fold zoom. ** SPECIAL1 ** PRIVACY ZONE ON (ENB) PROPO. P/T AREA TITLE ON (NESW) 1.
Camera Setting Setup menu *** SET UP MENU *** 1. To display the Camera Setting Menu PRESET 1* HOME POSITION • Move the cursor to CAMERA , and press the CAM (SET) key. SELF RETURN 10MIN AUTO MODE AUTO PAN The camera setting menu is displayed.
Page 33
• The positioning of the CAMERA ID stops at the edges of the CAMERA ID screen. 0123456789 ABCDEFGHIJKLM • The CAMERA ID moves faster when the joystick is kept NOPQRSTUVWXYZ ().,'":;&#!?= pressed for more than 0.5 seconds. +-*/%$ÄÜÖÆÑÅ • To return to SET UP for setting other items, move the cursor to SPACE POSI RET RESET RET, and press the CAM (SET) key.
Page 34
(2) ALC Mode with SUPER-D2 OFF Blinking 1. Move the cursor to the SUPER-D2 parameter and select OFF. (When you select MANUAL, SUPER-D2 is not available.) The item MASK SET appears on the menu. 2. Move the cursor to MASK SET and press the CAM (SET) key. The 48 mask areas appear on the monitor screen.
Page 35
4. Shutter Speed Setting (SHUTTER) Camera setting menu ** SET UP ** Note: When ON is selected for SUPER-D2 on the ALC CONT menu, CAMERA ID this item is not available. ALC/MANUAL SHUTTER To select electronic shutter speed, select OFF for SUPER-D2 in SENS UP the menu.
Page 36
7. Synchronization Setting (SYNC) Camera setting menu ** SET UP ** 1. Display SET UP on the monitor screen. CAMERA ID If necessary, refer to Setup Menu Display on page 14 for details ALC/MANUAL SHUTTER on displaying the SET UP menu on the monitor screen. SENS UP 2.
Page 37
8. Move the cursor to FINE by using the joystick. 9. Use the joystick to match the vertical phase for both video output signals as closely as possible. Notes: • When the “|” cursor reaches the “+” end, it jumps back to “–”. At the same time, COARSE is incremented by one step to enable a continuous adjustment.
Page 38
Camera setting menu (2) Automatic White Balance Control Mode (AWC) 1. Display SET UP on the monitor screen. ** SET UP ** CAMERA ID (Refer to Setup Menu Display on page 14 for details on displaying ALC/MANUAL SHUTTER the SET UP menu on the monitor screen.) SENS UP SYNC 2.
Page 39
Camera setting menu 9. Motion Detector Setting (MOTION DET) ** SET UP ** CAMERA ID 1. Display SET UP on the monitor screen. ALC/MANUAL SHUTTER (Refer to Setup Menu Display on page 14 for details on display- SENS UP ing the SET UP menu on the monitor screen.) SYNC WHITE BAL MOTION DET...
Page 40
Because the alarm signal is multiplexed on the video signal it may be mistakenly interpreted by other video equipment as a time code signal. Therefore, when this camera is not used in a Panasonic Intelligent CCTV System, select OFF to prevent the above from occurring.
Page 41
Camera setting menu 11. Special 2 Menu (SPECIAL2) ** SET UP ** This menu lets you adjust and set up the picture quality to meet your CAMERA ID requirements. ALC/MANUAL SHUTTER • Display SET UP on the monitor screen. SENS UP (Refer to Setup Menu Display on page 14 for details on display- SYNC WHITE BAL...
Page 42
(4) BW ** SPECIAL2 ** CHROMA GAIN •••• •••• Move the cursor to BW and select AUTO, ON or OFF by moving AP GAIN •••• •••• the joystick to the left or right. Default : OFF. PEDESTAL • ••••••• AUTO: The camera selects black and white mode if the picture is AUTO BURST(BW) →...
Confirm the system protocol and parameters prior to setting the com- munication parameters for the camera. The initial communication parameters for WV-CS850 and WV-CS854 are shown on the RS485 setup menu below. Other than the on-screen-setup parameters, the 4-bit DIP switch may be used to select 2-line (Half Duplex) or 4-line (Full Duplex) communication.
Page 44
AUTO 1: Transmits the alarm data each time an alarm signal is received. AUTO 2 (Default): Transmits alarm data every 5 seconds. For Panasonic’s NEW protocol (reserved for future use with connection to the personal computers) OFF: Transmits alarm data in response to requests from the controller.
Protcol Selection shown in the table. 2. Switch off the camera. Panasonic’s conventional 3. Switch on the camera to read in the Panasonic’s NEW generation changed switch settings. Note: The changed communication Paramater Selection parameters are displayed on the PARITY...
Page 46
Unit number Switch 1, an 8-bit DIP switch, specifies unit number for three protocols: Panasonic’s new and conven- tional protocol and AD protocol. When the unit number 1-32* or 1-96* is selected, it is set on the RS485 SETUP menu.
Page 47
For conventional Panasonic’s protocol Unit Unit Unit Switch Position Switch Position Switch Position Number Number Number 1-96* (to be continued)
Page 48
For conventional Panasonic’s protocol Unit Unit Unit Switch Position Switch Position Switch Position Number Number Number For AD’s protocol Unit Unit Unit Switch Position Switch Position Switch Position Number Number Number 1-32* Note: In case of using the cameras in combination with a controller and other peripherals of AD make, switch the cameras on after making sure that the controller and peripherals have already been turned AD is a registered trademark of American Dynamics.
Page 49
RS485 Setting Note: Remove sharp edges to protect the 4-bit DIP SW The 4-bit DIP switch in used for cables. RS485 termination and protocol selection. BP 1 Function Termination ON Switch Position Termination OFF b. Top cable exit BP 2 BP 3 BP 4 Function Prepare a hole in the ceiling board to run...
Page 50
3. Hook the Fall prevention wire on the camera 5. Tighten the fixing screw M3 (provided). mounting base. Notes : (1) Tighten the camera fixing screw with a screwdriver. (2) Follow the instructions given here to ensure that the camera and camera mounting base are installed safely.
• The following connections should be made by qualified service personnel or system installers in accordance with all local codes. • See the reverse side of the cover page for mains lead connection. 220 - 240 V AC (WV-CS850) 24 V AC Cable 24 V AC (WV-CS854)
Page 52
• RS485 connection Brown T (B) Data Transmission Orange T (A) Yellow R (B) Data Reception Green R (A) Note: Use the cable that is described below for RS485 site communication. • Shielded, twisted pair cable • Low impedance • Wire gauge size is thicker than AWG #22 (0.33 mm •...
SYSTEM CONNECTIONS Combination Camera Max. 64 Cameras Matrix Switcher Personal Computer VTRs (up to 16) RS-232C Port CONTROL ALARM INPUT INPUT INPUT INPUT INPUT INPUT INPUT OUTPUT OUTPUT OUTPUT OUTPUT DATA VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 RS-232C...
Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. SPECIFICATIONS WV-CS854 WV-CS850 Effective Pixels 737 (H) x 575 (V) Scanning Area 3.57 mm (H) x 2.67 mm (V), 1/4” Synchronization...
AUTO FOCUS MANUAL/AUTO AUTO MODE OFF/SEQ/SORT/AUTO PAN AUTO PAN KEY SEQ/SORT/AUTO PAN/PATROL PLAY Digital Flip ON/OFF CAMERA ID Preset ID, Camera ID, Area Title : Up to 16 characters SUPER D2 ON/OFF MOTION DET ON/OFF ALARM IN 4 Inputs (ALARM IN 1 - 4) ALARM OUT 2 Outputs (ALARM/AUX1, B/W/AUX2) B/W Mode...
APPENDIX Shortcuts Shortcut operations are available to controllers having the CAM FUNCTION key. Pressing numeric key(s) for one digit up to three digits then CAM FUNCTION key implements the respective functions as follows. The CAM FUNCTION key is abbreviated to [CAM FUNC] here. Function Function Selecting a PRESET position From #1 to #64...