Rf Transmitter Points; Key Fob Transmitters As Arm/Disarm & Control Devices - NAPCO Gemini GEM-P816 Programming Instructions Manual

WI995C 2/04
AREA OPTIONS
Disabled User Code not active in this area.
Arm/Disarm Allows User Code to arm/disarm this area.
Arm Only Prevents User Code from disarming this area.
Service A Service Code has restricted arm/disarm rights; if an area is armed with a Service Code, a "MONITOR ON" appears on the GEM-RP2ASe2 key-
pad and the area can be disarmed with any valid User Code, including a Service Code. If the area is armed with OTHER than a Service Code,
Ambush Allows user code to send Ambush signal to Central Station.
Access This is normally used to activate a door strike while an area is disarmed. Also program "Access Control on PGM2. Output" (Address 0719) and
"PGM2 Output Access Control Timeout" (Address 0711).
* User Program User Program Option is enabled for Keypad 1 only, wherever it is connected (Area 1 or Area 2). To enable User Program Option for any user
add 8 to the data entry for Area Option (see example). Then, User Programming can be performed only at Keypad 1 by a user code with user
program enabled.
Related User Options:"Enable Global Ambush Code" (Address 0720), "Global Ambush Code" (Address 1054) & "Enable Managers Mode" (Address 0719).
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above and press
cancel a code, blank out each number of the code and press
Z N # X M I T # + C S P
Z n 0 1 - 0 0 0 0 0 0 : 0 - 0
Zone # Xmitter Check
Mapped to ID Sum
; B =
G 0 G 1
C = ; D =
G 2
Z N # X M I T # + C S P
Z n 0 1 - 0 0 0 0 0 0 : 0 - 0
Z N # X M I T # + C S P
Z N 0 1 - E N R O L L : A - -
Example. A 2-point transmitter has the RF ID number 287613:1.
Map point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone "06".
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that
one point has been programmed. (Transmitter 287613:1, point
KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm
system, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the key
fob, the location where the person holding the key fob is stationed, or the special purpose of the key fob button being depressed.
See the next page on Key Fob Transmitters as Zone Input Devices .
K F A X M I T # + C S O P
0 1 - 0 0 0 0 0 0 0 : 0 0 0
KF Area Xmitter Check
# ID Sum
NOTE: When programming the ID Code number, "0" through "9" =
C = ; D =
G 2 G 3
L
NAPCO Security Systems
U
to save.
RF Transmitter Points (Press
For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)
•
The zone number (01–32) to which the transmitter will be mapped.
Point
•
The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
#
•
The point number (1–2); enter "9" for unsupervised (all points).
U
•
Press to save and NEXT/YES button to proceed when all transmitters have been entered.
NOTE: When programming the ID Code number, "0" through "9" =
;
; E =
G 3 G 4
Quick Method. If a receiver is already installed in the panel, transmitter wireless points can be
programmed automatically ("enrolled") using the following procedure. NOTE: The transmitter
point will be enrolled only if the signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be mapped.
2. Press to enter the Enroll Mode. The red and green LEDs on the keypad will flash and the
B
window will display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).
4. Install the transmitter battery. The keypad will beep to indicate that the point has been successfully
enrolled. Multi-point transmitters can be mapped to successive zones simultaneously.
Key Fob Transmitters as Arm/Disarm & Control Devices (Press
Key fobs can be programmed as "Arm/Disarm" devices using their On/Off buttons (refer to
WI752). For each Key Fob Transmitter, enter:
•
The Key Fob Transmitter number (01–8).
Aux
1&2
•
The area number to which transmitter is assigned (0 to disable keyfob, 1 or 2).
•
The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•
The Aux 1 Option (see key fob aux 1 & aux 2 options).
•
The Aux 2 Option (see key fob aux 1 & aux 2 options).
U
•
Press to save and NEXT/YES button to proceed when all key fobs have been entered.
; E = and "F" =
G 4
EXPLANATION
to set cursor.)
R
and "F" = .
G 5
1 will be mapped to Zone 6).
5. Enter Zone "09".
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad
will beep once to indicate that one point has been programmed.
(Transmitter 287613:1, point 2 is mapped to Zone 9).
through ; A =
0 9 G 0
.
G 5
X
GEM-P816 Programming Instructions
!
Page 9
U
to save. Similarly, to
through ; A =
0 9
to set cursor).
R
; B = ;
G 1