Storing The Antenna Name; Changing The Antenna - Kenwood TS-990S Instruction Manual
Hide thumbs
Also See for TS-990S:
- Service manual (245 pages) ,
- In-depth manual (107 pages) ,
- Instruction manual (75 pages)
Table of Contents
Advertisement
4 BASIC OPERATIONS
4 Press [-] (F4) or [+] (F5) to select one from "1" to "4".
The default is "3".
5 Press [
] (F1).
6 Press [MENU] to exit.
Note:
◆ The configured parameter also applies for the vertical meter used
in SWL mode.
STORING THE ANTENNA NAME
You can store an antenna name for the connected
antenna. If multiple antennas are used, band by band,
displaying the antenna name allows you to distinguish
which antenna you want to select.
F[ANT]
[ESC]
[F1] [F7] F[CHAR] F[DEL]
1 Press and hold [ANT] (F) to open the Antenna Name
screen.
2 Press [
] (F2) or [
MULTI/CH control to select the antenna connector to
which a name will be given.
3 Press [NAME] (F6) to allow editing of the parameter
box.
4 Enter the antenna name by pressing the function keys
or rotating the MULTI/CH control.
4-20
[RX/ANT]
[MULTI/CH]
] (F3), or rotate the
A maximum of 5 alphanumeric characters and symbols can
be entered.
[SPACE] (F1): Press to enter one space.
[-] (F2) or [+] (F3): Press to display the previous or next
character.
[
] (F4) and [
the left or right.
[SAVE] (F6): Stores the selected characters.
[BACK SPACE] (F): Press to delete the character to the left
of the cursor.
[DEL] (F): Press to delete the character to the right of the
cursor.
[CHAR] (F): Changes the character type. Each time you
press [CHAR] (F), the character type cycles through the
following sequence:
ABC (upper case) > abc (lower case) > ÀÁÂ (upper case) >
àáâ (lower case) > !"# (symbols) > ABC (upper case)
■ A vailable Characters and Symbols (A maximum of
5 characters)
Following are the available characters and symbols with
"English" selected in Menu 9-01. If you wish to enter the
Japanese characters, download the Japanese instruction
manual to refer to the available characters and symbols for
the Japanese characters.
A
B
C
D
E
F
G
P
Q
R
S
T
U
V
0
1
2
3
4
5
6
a
b
c
d
e
f
g
p
q
r
s
t
u
v
!
#
$
%
&
'
(
>
?
@
[
\
^
_
。 「
」
、
5 Press [SAVE] (F6) to save the antenna name.
6 Press [ESC] to exit.
CHANGING THE ANTENNA
You can change the antenna connected to the rear panel
according to your operating band. Parameters configured
for ANT1 to ANT4 and DRV will automatically be saved
in the antenna band memory. If you select the same
band next time, the same antenna will automatically be
selected.
1 Press [ANT] (F) to select the antenna.
Each key press cycles the operating mode through the
following sequence.
ANT1 > ANT2 > ANT3 > ANT4> ANT1
Frequency Range for the Selected Antenna (MHz)
0.03 to 0.522
0.522 to 2.5
2.5 to 4.1
4.1 to 6.9
6.9 to 7.5
7.5 to 10.5
] (F5): Press to move a pointer to
H
I
J
K
L
M
N
W
E
X
Y
Z
7
8
9
h
i
j
k
l
m
n
w
x
y
z
)
*
+
,
/
:
<
`
{
|
}
〜
10.5 to 14.5
14.5 to 18.5
18.5 to 21.5
21.5 to 25.5
25.5 to 30.0
30.0 to 60.0
Index
Contents
O
o
=
Advertisement
Table of Contents
