Baldor VS1GV4350-1T Vector Control Manuals

Manuals and User Guides for Baldor VS1GV4350-1T Vector Control. We have 1 Baldor VS1GV4350-1T Vector Control manual available for free PDF download: Installation & Operating Manual

Baldor VS1GV4350-1T Installation & Operating Manual

Baldor VS1GV4350-1T Installation & Operating Manual (204 pages)

VS1GV Series AC Closed Vector Control

Brand: Baldor | Category: Controller | Size: 7 MB

Table of Contents

Table of Contents
3
Chapter 1 Introduction

7
- Getting Assistance from Baldor
  7
- Safety Notices
  7
- Quick Start
  9
Chapter 2 General Information and Ratings

11
- Limited Warranty
  11
- Standards
  11
  - Design and Test Standards
    11
  - Environmental Test Standards
    11
  - Marks
    11
Chapter 3 Installing the Drive

13
- Receiving & Inspection
  13
- General Requirements for the Installation Site
  13
  - Location Instructions
    13
  - Minimum Mounting Clearances
    13
- Mounting the Drive
  13
  - Protecting the Drive from Debris
    13
  - Watts Loss Data
    13
- Cover Removal
  14
Chapter 4 Power Wiring

17
- Grounding the Drive
  17
  - Ungrounded Distribution System
    17
  - Input Power Conditioning
    17
- Line Impedence
  17
  - Line Reactors
    18
  - Load Reactors
    18
- Line Disconnect
  18
- Protective Devices
  18
- Reduced Input Voltage Considerations
  19
- Electrical Installation
  19
- Optional Filter/Reactor
  19
- Incoming Power and Motor Connections
  22
- Operating a 3-Phase Control on Single Phase Input Power
  23
  - Single Phase Power Derating
    23
- M-Contactor
  27
- Long Motor Leads
  27
- Optional Dynamic Brake Hardware
  28
- Encoder Installation
  29
- Home (Orient) Switch Input
  30
Chapter 5 Control Wiring

31
- Control Board Connections
  31
- Analog Inputs
  33
  - Analog Input 1
    33
  - Analog Input 2
    33
- Analog Outputs
  34
- Opto-Isolated Inputs
  34
- Operating Modes
  35
  - Keypad
    35
  - Standard Run 2-Wire
    36
  - Standard Run 3-Wire
    37
  - Preset Speeds
    38
  - Fan Pump 2-Wire
    39
  - Fan Pump 3-Wire
    40
  - Process Control
    41
  - Speed Analog 2-Wire
    42
  - Speed Analog 3-Wire
    43
  - E-POT 2-Wire
    44
  - E-POT 3-Wire
    45
  - Network
    46
  - Profile Run
    47
  - Preset Position
    48
  - Bipolar
    51
  - Pulse Follower
    53
  - Plc
    53
- Digital Outputs
  53
- Relay Outputs
  54
- USB Port
  54
- Communication Expansion Boards
  55
  - RS485 Modbus
    55
- Opto-Isolated Inputs
  56
- Opto-Isolated Outputs
  56
- Pre-Operation Checklist
  57
- Powerup Procedure
  57
- Mint Workbench
  58
  - Install USB Driver
    58
  - Install Mint Workbench
    59
  - Update Firmware
    61
Chapter 6 Using the Keypad

63
- Keypad Components
  63
  - Display Description
    63
  - Display Features
    64
- Status Mode
  65
- Menu Display
  66
- Basic Params
  66
- Save Parameter Values
  69
- Restore Parameter Values
  70
- Advanced Prog
  71
  - Modified Parameters
    72
  - Linear List
    72
- Event Log
  73
- Diagnostics
  74
- Display Options
  76
- Operating the Control from the Keypad
  77
  - Accessing the Keypad JOG Command
    77
  - Speed Adjustment Using Local Speed Reference
    77
Chapter 7 Parameter Descriptions

79
Chapter 8

117
Customizing Your Application

117
Chapter 9 Troubleshooting

119
- Event Log
  119
- Diagnostic Information
  124
- Fault Messages
  126
- Electrical Noise Considerations
  131
Chapter 10 PLC Mode Description

133
- Overview
  133
- Comparator Function
  133
- Timers
  134
- PLC Mode as Standard Run 2-Wire Mode
  140
- PLC Mode as 15 Preset Speed Mode
  141
- PLC Mode as Process PID Mode
  142
- PLC Mode as a Modified Process PID Mode
  143
Chapter 11 Composite Reference Description 11.1 Overview ...................................................................... 11-1

146
- Composite Reference Examples
  146
Chapter 12 Monitor and RTC Description 12.1 Monitor Parameters (P0001 to P0202) ................................................ 12-1

152
- Real Time Clock (RTC) Overview
  152
Appendix A

157
Appendix B

173
Appendix C

191
- C.1 Outline
  191
- C.3 EMC Installation Options
  192
- C.7 EMC Wiring Technique
  193
- C.8 EMC Installation Instructions
  194
Appendix D

195
- D.1 Dynamic Braking (DB) Hardware
  195
- D.2 Expansion Boards
  196
- D.3 Keypad Extension Cables
  197
- D.4 Optional Remote Keypad Installation
  198
Appendix E

199
Remote Keypad Mounting Template

199

Advertisement

Advertisement

Related Products

Baldor Categories

Controller Inverter Portable Generator Servo Drives Engine

More Baldor Manuals