CMA Dishmachines L-1C Owner's Manual
Hide thumbs
Also See for L-1C:
- Parts manual (14 pages) ,
- Quick setup instructions (2 pages) ,
- Quick setup instructions (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CMA Dishmachines L-1C
Summary of Contents for CMA Dishmachines L-1C
- Page 1 Owner’s Manual Keep with machine for reference MODEL L-1C Installation & Operations Rev 1.00A C M A D I S H M A C H I N E S 1 2 7 0 0 K N O T T A V E N U E...
-
Page 2: Table Of Contents
ABLE OF ONTENTS CMA-L-1C ODEL 1. SPECIFICATIONS ..................2 1.1. L-1C ..............................2 1.2. L-1C O ......................3 PERATIONAL YCLE 2. GETTING STARTED ..................5 2.1. L-1C......................5 NTRODUCTION TO THE 2.2....................... 6 ECEIVING AND NSTALLATION 2.2.1. Electrical ..........................6 2.2.2. -
Page 3: Specifications
65 PSIG are present, a pressure regulating valve must be installed in the water line to the dishwasher (by others). If flowing pressure is lower than 15 psi, improper machine operation may result. Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A... -
Page 4: L-1C Operational Cycle
1.2. L-1C Operational Cycle The L-1C Operational Cycle has a total cycle time of 2 minutes (120 seconds). The Timing Diagram and the steps listed below detail the individual functions that are executed during each Operational Cycle. Seconds: Instant Start Relay... - Page 5 7. Cam switch 8 operates the optional sustainer heater. This cam assures that the sustainer heater only turns on when the dishmachine is not in a cycle. This prevents the machine from drawing too much electrical current at any one time. Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A...
-
Page 6: Getting Started
The supply water to the L-1C must be a minimum of 140°F. The pipe supplying the water must be ½” minimum. The plumbing connection is located at the back of the glasswasher. The drain is a 1" barbed fitting located at the back of the glasswasher for easy attachment of your drain hose. -
Page 7: Receiving And Installation
Prior to installation make sure the electrical supply is compatible with the specifications on the machines data plate A 15-amp, 115 volt, 60 Hz dedicated circuit must be used to supply electrical power to the L-1C Glasswasher (see specification sheet page 1). -
Page 8: Plumbing
Federal, State, and Local Health, Electrical, Plumbing and Safety codes The de-liming agents used to de-scale a commercial dishwasher, are highly caustic and de-liming must be done by a qualified chemical specialist. Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A... -
Page 9: Operation
The chemicals and water level must be programmed by a qualified chemical specialist. The de-liming agents are highly caustic and de-liming must be done by qualified chemical specialist. Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A... -
Page 10: Pre-Scrapping
Cam 4 can be adjusted to increase the amount of water that is automatically fed into the machine during a cycle (see section 4.1.1 Cam Adjustment). Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A... -
Page 11: Maintenance
5. Adjust the trailing edge of the cam groove by rotating the appropriate side of the cam in the proper direction to either increase or decrease the cam’s groove; resulting in increasing or decreasing the total time that switch will be held ON. Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A... -
Page 12: Quick Service Guide
NORMAL Delimer switch in wrong position Switch to position Sanitizer pump does not run Faulty 5th micro switch Replace switch, P/N 00411.00 Faulty sanitizer pump motor Replace motor, P/N 00416.00 Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A... -
Page 13: Troubleshooting
Defective fill/start switch (cycle Replace fill/start switch start switch does not begin light will not light either) P/N: 03470.01 cycle Replace timer assembly* Defective timer assembly (Cam 1) P/N: 00408.80 Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A... - Page 14 P/N: 03470.00 Defective sani pump motor Replace pump motor P/N: 00416.00 Activating rinse primer Defective rinse primer switch Replace primer switch switch does not run pump P/N: 03470.00 Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A...
- Page 15 P/N: 00201.00 *The timer assembly motor ( ) or micro switches ( ) can be replaced P/N: 00501.00 P/N: 00411.00 independently if that is the only component that has failed. Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A...
-
Page 16: Addendum For Machines Installed In The City Of Chicago
1. All low energy models must have low level sani-alarms, both visual and audio. 2. All models must have a City of Chicago approval data label affixed to the glasswasher. 3. Chlorine sanitizer must be a minimum of 100 PPM. Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A... -
Page 17: Appendix A: Operator & Cleaning Instructions
Appendix A: Operator & Cleaning Instructions Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A... -
Page 18: Electrical Diagram
Electrical Diagram 5. Electrical Diagram Page MODEL L-1C INSTALLATION & OPERATION MANUAL Rev. 1.00 A...
Need help?
Do you have a question about the L-1C and is the answer not in the manual?
Questions and answers