Installation Requirements; Tools And Parts - Maytag UXT2030AY Installation Instructions And Use & Care Manual

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed (all models)
Drill
1¹⁄₄" (3.0 cm) drill bit
¹⁄₈" (3.0 mm) drill bit for pilot holes
Pencil
Wire stripper or utility knife
Tape measure or ruler
Caulking gun and weatherproof caulking compound
Flat-blade screwdriver
Phillips screwdriver
Saber or keyhole saw
Metal snips
Compass or 8" (20.3 cm) circle template
Parts Supplied (all models)
®†
T-10 Torx adapter
®†
T-20 Torx adapter
4 - 4.5 x 13 mm mounting screws
Parts Needed (all models)
3 - UL listed wire connectors
Vent clamps/duct tape as required
For cabinets with recessed bottoms:
Two 2" (5.1 cm) wide filler strips. Length and thickness
determined by recess dimensions.
Four flat head wood screws or machine screws with washers
and nuts (to attach filler strips).
Models UXT2030AY/UXT2036AY (vented installation)
Parts supplied
Remove parts from package. Check that all parts are included.
2 - 3.5 x 9.5 mm screws
7" (17.8 cm) round vent mounting plate
Parts needed
7" (17.8 cm) round metal vent system
Wall or roof cap with damper to match vent system
1 - 75W max, 120V incandescent light bulb
Models UXT3030AY/UXT3036AY (vented installation)
Parts supplied
Remove parts from package. Check that all parts are included.
2 - 3.5 x 9.5 mm screws
3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vent connector
†®TORX is a registered trademark of Saturn Fasteners, Inc.
4

INSTALLATION REQUIREMENTS

Tools and Parts

Parts needed
3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular metal vent system
Wall or roof cap with damper to match vent system
1 - 75W max, 120V incandescent light bulb
Models UXT4030AY/UXT4036AY
(recirculation installation only)
Parts needed
1 - 75W max, 120V incandescent light bulb
Models UXT4230AY/UXT4236AY
(vented or non-vented [recirculation] installation)
Parts supplied
Remove parts from package. Check that all parts are included.
2 - 3.5 x 9.5 mm screws
3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vent connector
Parts needed
1 - 75W max, 120V incandescent light bulb
Wall or roof cap with damper to match vent system
For 7" (17.8 cm) round vented installations:
7" (17.8 cm) round metal vent sytem
7" (17.8 cm) round damper. For information on ordering, see
the "Accessories" section.
7" (17.8 cm) round vent mounting plate. For information on
ordering, see the "Accessories" section.
For 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vented installations:
3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular metal vent system
For non-vented (recirculation) installations:
Charcoal filter kit. For information on ordering, see the
"Accessories" section.
Models UXT5230AY/UXT5236AY
(vented or non-vented [recirculation] installation)
Parts supplied
Remove parts from package. Check that all parts are included.
2 - 3.5 x 9.5 mm screws
3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular damper/vent connector
Parts needed
Wall or roof cap with damper to match vent system
For 7" (17.8 cm) round vented installations:
7" (17.8 cm) round metal vent sytem
7" (17.8 cm) round damper. For information on ordering, see
the "Accessories" section.
7" (17.8 cm) round vent mounting plate. For information on
ordering, see the "Accessories" section.
For 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vented installations:
3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular metal vent system
For non-vented (recirculation) installations:
Charcoal filter kit. For information on ordering, see the
"Accessories" section.