Hilti SID 14­A Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Impact Driver
  5. SID 14-A
  6. Operating instructions manual

Hilti SID 14­A Operating Instructions Manual

Cordless impact driver/wrench
Hide thumbs Also See for SID 14­A:

Advertisement

Table of Contents

See also: Manual
Printed: 30.09.2013 | Doc-Nr: PUB / 5070695 / 000 / 02
SID/SIW
14-A/18-A
Operating instructions
Mode d'emploi
Manual de instrucciones
en
fr
es

Advertisement

Table of Contents
loading

Related Manuals for Hilti SID 14­A

Summary of Contents for Hilti SID 14­A

  • Page 1 SID/SIW 14-A/18-A Operating instructions Mode d’emploi Manual de instrucciones Printed: 30.09.2013 | Doc-Nr: PUB / 5070695 / 000 / 02...
  • Page 2 Printed: 30.09.2013 | Doc-Nr: PUB / 5070695 / 000 / 02...
  • Page 3 ETL listed to US and Canadian safety standards Homologué ETL (conforme aux normes de sécurité américaines et canadiennes) Producto homologado según normas de seguridad americanas y canadienses Produto homologado de accordo com as normas de segurança americanas e canadianas Printed: 30.09.2013 | Doc-Nr: PUB / 5070695 / 000 / 02...
  • Page 4 Printed: 30.09.2013 | Doc-Nr: PUB / 5070695 / 000 / 02...
  • Page 5 14.4 Volt Li-Ion 14.4 Volt Li-Ion 1.6 Ah 1.6 Ah Printed: 30.09.2013 | Doc-Nr: PUB / 5070695 / 000 / 02...

  • Page 6: Table Of Contents

    ORIGINAL OPERATING INSTRUCTIONS SID 14­A / SID 18­A / SIW 14­A / SIW 18­A cordless impact driver/wrench It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. Ensure that the operating instructions are with the power tool when it is given to other persons.

  • Page 7: General Information

    Operating controls and parts SIW square drive SID hex. socket drive Light Control switch (with electronic speed control) Forward / reverse switch & Motor brake Torque selector switch SID/W 18­A battery release buttons SID/W 14­A battery release button § Charge status and fault display (Li-ion battery) Belt hook (optional) 1 General information 1.1 Safety notices and their meaning...
  • Page 8 The type designation can be found on the type identification plate and the serial number on the side of the motor housing. Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. Type: Generation: 01 Serial no.:...

  • Page 9: Description

    Do not use the battery as a power source for other unspecified appliances. Modification of the power tool or tampering with its parts is not permissible. To avoid the risk of injury, use only genuine Hilti accessories and insert tools.

  • Page 10: Insert Tools, Accessories

    2.4 Additional items required for operating the tool B 18/1.6 Li­Ion, B 18/2.6 Li­Ion, B 18⁄3.3 Li­Ion, B 14/1.6 Li­Ion or B 14/3.3 Li­Ion battery with C4⁄36­90, C4⁄36­350, C 4/36, C 4/36­ACS or C 4/36­ACS TPS charger. 2.5 Li­ion battery charge status LEDs light constantly LEDs blink Charge status C...

  • Page 11: Technical Data

    Designation Description Bits Hex. bit, bit adapter, drill bits with hex. shank Sockets Impact wrench sockets 4 Technical data Right of technical changes reserved. Power tool SID 14­A SIW 14­A Rated voltage 14.4 V 14.4 V Weight (including bat- 1.3 kg (2.87 lb) 1.3 kg (2.87 lb) tery and chuck) Dimensions (L x W x...
  • Page 12 Power tool SID 18­A SIW 18­A Rated voltage 21.6 V 21.6 V Weight (including bat- 1.5 kg (3.31 lb) 1.5 kg (3.31 lb) tery and chuck) Dimensions (L x W x 151 mm (5.94") x 154 mm (6.06") x 94 mm (3.7") x 94 mm (3.7") x 228 mm (8.98") 228 mm (8.98")

  • Page 13: Safety Instructions

    Power tool Position I Position II Position III SID 18­A 60 Nm (44 lb/ft) 110 Nm (81 lb/ft) 165 Nm (122 lb/ft) SIW 18­A (³⁄₈" 75 Nm (55 lb/ft) 120 Nm (89 lb/ft) 175 Nm square drive) (129 lb/ft) SIW 18­A 90 Nm (66 lb/ft) 135 Nm 200 Nm...
  • Page 14 5.1 General power tool safety warnings WARNING Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
  • Page 15 or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
  • Page 16 before use. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions taking into account the working conditions and the work to be performed.
  • Page 17 e) Improve the blood circulation in your fingers by relaxing your hands and exercising your fingers during breaks between working. Avoid touching rotating parts. Switch the power tool on only after bringing it into position at the workpiece. Touching rotating parts, especially rotating insert tools, may lead to injury.
  • Page 18 Place the tool in a location where it can be kept under observation, well away from flammable materials, and allow it to cool down. Contact Hilti Service after the battery has been allowed to cool. 5.2.4 Electrical safety Before beginning work, check the working area (e.g. using a metal detector) to ensure that no concealed electric cables or gas and water pipes are present.

  • Page 19: Before Use

    5.2.6 Personal protective equipment The user and any other persons in the vicinity must wear ANSI Z87.1- approved eye protection, a hard hat, ear protection, protective gloves and breathing protection while the machine is in use. 6 Before use 6.1 Battery use and care NOTE Battery performance drops at low temperatures.
  • Page 20 CAUTION Before fitting the battery, check that the power tool is switched off and that the safety lock is engaged (forward/reverse switch in the middle position). Use only the Hilti batteries approved for use with this power tool. CAUTION Check that the terminals on the battery and in the power tool are free from foreign objects before inserting the battery in the power tool.

  • Page 21: Operation

    6.4 Removing the battery 1. Press one or both release buttons. 2. Pull the battery out of the power tool toward the rear. 6.5 Transport and storage of battery packs Pull the battery pack out of the locked position (working position) and move it into the first click-stop position (transport position).
  • Page 22 7.1.2 Changing insert tools with the SIW 14-A and SIW 18-A NOTE The power tool is equipped with two different chucks: ¹/₂" square drive with ball-notch retention or ³/₈" with locking ring 7.1.2.1 Fitting the socket 1. Set the forward / reverse switch to the middle position or remove the battery from the power tool.
  • Page 23 7.5 Driving screws and tightening bolts 7.5.1 Fitting the bit / bit holder 1. Set the forward / reverse switch to the middle position or remove the battery from the power tool. 2. Fit the appropriate insert tool in the chuck. 7.5.2 Screwdriving WARNING Ensure fastener and attachment will withstand the level of torque...

  • Page 24: Care And Maintenance

    Do not operate the power tool if parts are damaged or when the controls do not function faultlessly. If necessary, the power tool should be repaired by Hilti Service. 8.4 Care of the Li-ion battery Avoid entrance of moisture.

  • Page 25: Troubleshooting

    Charge the battery with the Hilti charger approved for use with Li-ion batteries. NOTE – A conditioning charge (as is required with NiCd or NiMH batteries) is not necessary. – Interruption of the charging procedure has no negative effect on battery life.

  • Page 26: Disposal

    Remedy The battery runs Battery condition is not Have battery condition down more quickly optimal. diagnosed by Hilti Ser- than usual. vice or replace with a new battery. The battery doesn’t The retaining lugs on the Clean the retaining lugs engage with an audi- battery are dirty.

  • Page 27: Manufacturer's Warranty - Tools

    11 Manufacturer’s warranty - tools Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty is valid so long as the tool is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti Operating Instructions, and the technical system is maintained.
  • Page 28 LI-9494 Schaan Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3984 | 0713 | 00-Pos. 3 | 1 Printed in China © 2013 2012668 / A3 Right of technical and programme changes reserved S. E. & O...

This manual is also suitable for:

Siw 18t-aSid 18-a

Table of Contents