Avery Dennison 64-Series User Manual page 80

11/14 Rev. 03
AP 4.4 – AP 5.4 – AP 5.6 – AP 7.t – 64-xx – DPM – PEM – ALX 92x
#G-------------------------------------------------------------------
#G Peripheral Parameter Menu
#G-------------------------------------------------------------------
#PC2512/1
#PC2501/0
#PC2502/100
#PC2503/250
#PC2504/170
#PC2505/170
#PC2506/0
#PC2507/30
#PC2508/95
#PC2509/50
#PC2510/0
#PC2511/120
#G-------------------------------------------------------------------
#G Dispenser Interface
#G-------------------------------------------------------------------
#PC3001/0
#PC3002/0.0
#PC3003/0
#PC3004/0
#PC3005/0
#PC3006/1
#PC3007/0
#PC3013/60.0
#PC3008/0
#PC3012/0
#PC3009/0
#PC3010/1
#PC3011/0
#G-------------------------------------------------------------------
#G Textile Parameter Menu
#G-------------------------------------------------------------------
#PC3301/1
#PC3302/1
#PC3303/10
#PC3304/1
#PC3305/0
#G-------------------------------------------------------------------
#G Applicator Parameter Menu
#G-------------------------------------------------------------------
#PC3101/0
#PC3102/0
#PC3110/2
#PC3103/0
#PC3104/0
#PC3105/0.0
#PC3106/1
#PC3107/1
#PC3108/0
#PC3109/2000
#PC3212/0
#G-------------------------------------------------------------------
#G I/O Board Parameter Menu
#G-------------------------------------------------------------------
#PC3201/0.0
#PC3202/0
#PC3203/0
#PC3204/0
#PC3205/0
#PC3206/0
#PC3207/0
#PC3208/0
#PC3209/1
#PC3210/0
#PC3211/0
#G-------------------------------------------------------------------
USER MANUAL
#G Rewinder Motor
#G Current mode
#G Min rew. current : 100
#G Max rew. current : 250
#G Min rew. current : 170 %
#G Max rew. current : 170 %
#G Start rew. curr. :
#G Start cur. len.
#G Pullback current : 95
#G Back diameter
#G Break current
#G Break diameter
#G Interface type
#G Start delay
#G Start print mode : Pulse falling
#G End print mode
#G Reprint signal
#G Ribbon signal
#G Material signal
#G Diam. mat. end
#G Feed input
#G Pause input
#G Start error stop : Off
#G Internal inputs
#G Apply mode
#G Changelabel Mode : Always at jobend
#G Changelab Print
#G Changelab Length : +
#G Label Eject Mode : Yes, at job end
#G Head lift autom. : after
#G Applicator type
#G Apply mode
#G Start print mode : Pulse rising
#G Start error stop : Off
#G APSF sensor res. :
#G Start delay
#G Dwell time
#G Blow on time
#G Restart delay
#G Position timeout :
#G Start error stop : Off
#G Start delay
#G APSF sensor res. :
#G Start print mode : Pulse falling
#G Reprint signal
#G Feed input
#G Pause input
#G Error output
#G Error polarity
#G Status output
#G Status polarity
#G End print mode
Advanced Applications
: Generation 2
: Table values
0 %
: 30 mm
: 50 mm
: 0
: 120 mm
: USI interface
: 0.0 mm
: Mode 0
: Disabled
: Enabled
: Disabled
: 60.0 mm
: Standard
: Standard
: Enabled
: After start sig.
: With print
10 mm
0 labels
: LTP - LTPV
: After start sig.
0 pulses/m
: 0.0 mm
: 1 ms
: 1 ms
: 0 ms
2000 ms
: 0.0 mm
0 pulses/m
: Disabled
: Disabled
: Disabled
: Printer error
: Level low active
: Low ribbon warn.
: Level low active
: Mode0 inactive
41