Toshiba e-Studio 162 Service Manual page 87

Main Sub
Contents
code code
46 01 Copy density adjustment
(300dpi) (EXP.LEVEL 300)
02 Copy density adjustment
(600dpi) (EXP.LEVEL 600)
[Function]
Copy density is set for each mode.
When this test command is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the copy becomes darker. When the set value is decreased, the
copy becomes lighter.
In this case, only Exp.3 copy is made. When, however, the setting is made to make darker copy,
Exp.1 and Exp.5 copies also become darker. When made to lighter copy, Exp1. and Exp.5 copies
become lighter, too.
← →
Press [ / ] key to switch the mode. The set value of the selected mode is displayed on the LCD.
(Adjustment value: 1 – 99)
The setting procedure of the magnification ratio is the same as that to copy operation.
Mode
AE mode (300dpi)
TEXT mode (300dpi)
PHOTO mode
TS mode (TEXT)(300dpi)
TS mode (AE)(300dpi)
[Operation]
1) Initial display
46-01 EXP.LEVEL 300
AE 100% 50( 1-99)
←
2) [ ] Mode selection
46-01 EXP.LEVEL 300
TSAE 100% 50( 1-99)
→
2) [ ] Mode selection
46-01 EXP.LEVEL 300
TEXT 100% 50( 1-99)
3) [10KEY] Value entry
46-01 EXP.LEVEL 300
AE 100% 62( 1-99)
[Function]
Copy density is set for each mode.
When this test command is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the copy becomes darker. When the set value is decreased, the
copy becomes lighter.
In this case, only Exp.3 copy is made. When, however, the setting is made to make darker copy,
Exp.1 and Exp.5 copies also become darker. When made to lighter copy, Exp1. and Exp.5 copies
become lighter, too.
← →
Press [ / ] key to switch the mode. The set value of the selected mode is displayed on the LCD.
(Adjustment value: 1 – 99)
Mode
AE mode (600dpi)
TEXT mode (600dpi)
PHOTO mode
TS mode (TEXT) (600dpi)
TS mode (AE) (600dpi)
[Operation]
The operation is similar to test command 46-01.
e-STUDIO162/162D/151/151D TEST COMMAND, TROUBLE CODES 10 - 18
Details of function/operation
Display item Default
AE 50 COPY mode lamp
TEXT 50 PRINT mode lamp
PHOTO 50 SCAN mode lamp
TSTXT 50 PRINT mode lamp
SCAN mode lamp
TSAE 50 COPY mode lamp
SCAN mode lamp
4) [START] Fixing and printing value (No
change on the LCD)
∗
Print is started in the set mode.
46-01 EXP.LEVEL 300
AE 100% 62( 1-99)
4) To fix the set value without printing, press
[OK (ENTER)] key.
46-01 EXP.LEVEL 300
AE 100% 62( 1-99)
∗
To cancel manual feed paper empty MSG,
press any key.
∗
When performing the AE mode exposure
adjustment, place the test chart on the docu-
ment table so that the center area of 10cm is
not covered.
Display item Default
AE 50 COPY mode lamp
TEXT 50 PRINT mode lamp
PHOTO 50 SCAN mode lamp
TSTXT 50 PRINT mode lampSCAN mode lamp
TSAE 50 COPY mode lampSCAN mode lamp
LED
LED