Rosen DP-1001 Owner's Manual page 98

2 By default, Rosen Navigation proposes the country/state and city where you are If needed, tap the
button with the name of the country/state, and select a different one from the list
3.
If needed, change the city:
'9
• To select the city from the list of recently used ones, tap the button
• To enter
a
new city:
1. Tap the button with the name of the city. or if you have changed the country/state, tap
<City Name>
2 Start entering the city name on the keyboard
3 Get to the list of search results:
• After entering a couple of characters, the names that match the string appear in a
list.
Done
,
• Tap
4 Pick the city from the list.
4.
Enter the street name:
<Street Name>
to open the list of results before it appears automatically
1
Tap
2
Start entering the street name on the keyboard
3. Get to the list of results:
• After entering a couple of characters the names that match the string appear in a list
Done
• Tap to open the list of results before it appears automatically.
4.
Pick the street from the list.
5.
Enter the house number:
<House Number>
1 Tap
2 Enter the house number on the keyboard.
Done
6
7
3 Tap to finish entering the address
A list appears with the matching addresses. Tap the desired one.
f~::
Set
as Destination
The map appears with the selected point in the middle Tap (Advanced mode) from
the Cursor menu The route is then automatically calculated, and you can start navigating
3.1.2A Entering an address without Imowing the district/suburb
Long roads can run across several districts or suburbs. You may not know if a particular house number is In
which of them. In this case, follow the instructions below:
The procedure is explained starting from the Navigation menu.
23
2 By default, Rosen Navigation proposes the country/state and city where you are If needed, tap the
button with the name of the country/state, and select a different one from the list
3.
If needed, change the city:
'9
• To select the city from the list of recently used ones, tap the button
• To enter
a
new city:
1. Tap the button with the name of the city. or if you have changed the country/state, tap
<City Name>
2 Start entering the city name on the keyboard
3 Get to the list of search results:
• After entering a couple of characters, the names that match the string appear in a
list.
Done
,
• Tap
4 Pick the city from the list.
4.
Enter the street name:
<Street Name>
to open the list of results before it appears automatically
1
Tap
2
Start entering the street name on the keyboard
3. Get to the list of results:
• After entering a couple of characters the names that match the string appear in a list
Done
• Tap to open the list of results before it appears automatically.
4.
Pick the street from the list.
5.
Enter the house number:
<House Number>
1 Tap
2 Enter the house number on the keyboard.
Done
6
7
3 Tap to finish entering the address
A list appears with the matching addresses. Tap the desired one.
f~::
Set
as Destination
The map appears with the selected point in the middle Tap (Advanced mode) from
the Cursor menu The route is then automatically calculated, and you can start navigating
3.1.2A Entering an address without Imowing the district/suburb
Long roads can run across several districts or suburbs. You may not know if a particular house number is In
which of them. In this case, follow the instructions below:
The procedure is explained starting from the Navigation menu.
23
2 By default, Rosen Navigation proposes the country/state and city where you are If needed, tap the
button with the name of the country/state, and select a different one from the list
3.
If needed, change the city:
'9
• To select the city from the list of recently used ones, tap the button
• To enter
a
new city:
1. Tap the button with the name of the city. or if you have changed the country/state, tap
<City Name>
2 Start entering the city name on the keyboard
3 Get to the list of search results:
• After entering a couple of characters, the names that match the string appear in a
list.
Done
,
• Tap
4 Pick the city from the list.
4.
Enter the street name:
<Street Name>
to open the list of results before it appears automatically
1
Tap
2
Start entering the street name on the keyboard
3. Get to the list of results:
• After entering a couple of characters the names that match the string appear in a list
Done
• Tap to open the list of results before it appears automatically.
4.
Pick the street from the list.
5.
Enter the house number:
<House Number>
1 Tap
2 Enter the house number on the keyboard.
Done
6
7
3 Tap to finish entering the address
A list appears with the matching addresses. Tap the desired one.
f~::
Set
as Destination
The map appears with the selected point in the middle Tap (Advanced mode) from
the Cursor menu The route is then automatically calculated, and you can start navigating
3.1.2A Entering an address without Imowing the district/suburb
Long roads can run across several districts or suburbs. You may not know if a particular house number is In
which of them. In this case, follow the instructions below:
The procedure is explained starting from the Navigation menu.
23