Rosen DP-1001 Owner's Manual page 120

Name
Distance
Remaining
Time Remaining
Arrival Time
GPS Time
Altitude
Speed Limit
Trip Computer
Next Via Point
Description Function
number. map screen in one of the Trip
Data fields.
Shows the distance you need to travel on the route Tap this field to show it on the
before reaching your final destination. map screen in one of the Trip
Data fields
Shows the time needed to reach the final destination of Tap this field to show it on the
the route based on information available for the map screen in one of the Trip
remaining segments of the route The calculation cannot Data fields
take into account traffic jams and other possible delays
Shows the estimated arrival time at the final destination Tap this field to show it on the
of the route based on information available for the map screen in one of the Trip
remaining segments of the route. The calculation cannot Data fields
take into account traffic jams and other possible delays.
Shows the current time corrected with time zone offset. Tap this field to show it on the
The accurate time comes from the GPS satellites, and map screen in one of the Trip
the time zone information comes from the map or it can Data fields.
be set manually in Regional settings.
Shows the elevation if it is provided by the GPS receiver. Tap this field to show it on the
map screen in one of the Trip
Data fields.
Shows the speed limit of the current street if the map Tap this field to show it on the
contains
it
map screen in one of the Trip
Data fields.
Opens a new screen with three
resettable Trip Computers
Tap this button to change the
content of the Route Data fields
to show information about the
next via point.
Destination
If you tap the previous button, this one replaces it.
Tap this button and the Route
Data fields show information
about the final destination again.
Most of the fields on this screen have a
I
symbol next to them. This symbol shows whether the field is shown
on the map as a Trip Data. It also shows the position of the data as follows:
Symbol
Description
I
This value is not shown on the map screen.
Ii
This value appears on the map screen in the Trip Data area This is the value at the
top.
a
This value appears on the map screen in the Trip Data area. This is the value in the
middle.
~
This value appears on the map screen in the Trip Data area. This is the value at the
bottom
45
Name
Distance
Remaining
Time Remaining
Arrival Time
GPS Time
Altitude
Speed Limit
Trip Computer
Next Via Point
Description Function
number. map screen in one of the Trip
Data fields.
Shows the distance you need to travel on the route Tap this field to show it on the
before reaching your final destination. map screen in one of the Trip
Data fields
Shows the time needed to reach the final destination of Tap this field to show it on the
the route based on information available for the map screen in one of the Trip
remaining segments of the route The calculation cannot Data fields
take into account traffic jams and other possible delays
Shows the estimated arrival time at the final destination Tap this field to show it on the
of the route based on information available for the map screen in one of the Trip
remaining segments of the route. The calculation cannot Data fields
take into account traffic jams and other possible delays.
Shows the current time corrected with time zone offset. Tap this field to show it on the
The accurate time comes from the GPS satellites, and map screen in one of the Trip
the time zone information comes from the map or it can Data fields.
be set manually in Regional settings.
Shows the elevation if it is provided by the GPS receiver. Tap this field to show it on the
map screen in one of the Trip
Data fields.
Shows the speed limit of the current street if the map Tap this field to show it on the
contains
it
map screen in one of the Trip
Data fields.
Opens a new screen with three
resettable Trip Computers
Tap this button to change the
content of the Route Data fields
to show information about the
next via point.
Destination
If you tap the previous button, this one replaces it.
Tap this button and the Route
Data fields show information
about the final destination again.
Most of the fields on this screen have a
I
symbol next to them. This symbol shows whether the field is shown
on the map as a Trip Data. It also shows the position of the data as follows:
Symbol
Description
I
This value is not shown on the map screen.
Ii
This value appears on the map screen in the Trip Data area This is the value at the
top.
a
This value appears on the map screen in the Trip Data area. This is the value in the
middle.
~
This value appears on the map screen in the Trip Data area. This is the value at the
bottom
45
Name
Distance
Remaining
Time Remaining
Arrival Time
GPS Time
Altitude
Speed Limit
Trip Computer
Next Via Point
Description Function
number. map screen in one of the Trip
Data fields.
Shows the distance you need to travel on the route Tap this field to show it on the
before reaching your final destination. map screen in one of the Trip
Data fields
Shows the time needed to reach the final destination of Tap this field to show it on the
the route based on information available for the map screen in one of the Trip
remaining segments of the route The calculation cannot Data fields
take into account traffic jams and other possible delays
Shows the estimated arrival time at the final destination Tap this field to show it on the
of the route based on information available for the map screen in one of the Trip
remaining segments of the route. The calculation cannot Data fields
take into account traffic jams and other possible delays.
Shows the current time corrected with time zone offset. Tap this field to show it on the
The accurate time comes from the GPS satellites, and map screen in one of the Trip
the time zone information comes from the map or it can Data fields.
be set manually in Regional settings.
Shows the elevation if it is provided by the GPS receiver. Tap this field to show it on the
map screen in one of the Trip
Data fields.
Shows the speed limit of the current street if the map Tap this field to show it on the
contains
it
map screen in one of the Trip
Data fields.
Opens a new screen with three
resettable Trip Computers
Tap this button to change the
content of the Route Data fields
to show information about the
next via point.
Destination
If you tap the previous button, this one replaces it.
Tap this button and the Route
Data fields show information
about the final destination again.
Most of the fields on this screen have a
I
symbol next to them. This symbol shows whether the field is shown
on the map as a Trip Data. It also shows the position of the data as follows:
Symbol
Description
I
This value is not shown on the map screen.
Ii
This value appears on the map screen in the Trip Data area This is the value at the
top.
a
This value appears on the map screen in the Trip Data area. This is the value in the
middle.
~
This value appears on the map screen in the Trip Data area. This is the value at the
bottom
45