Rosen DP-1001 Owner's Manual page 25

Function
Post DRC
On/Off/Auto To set up the post DRC ratio of sound. It is suggested that the post
DRC is set up to "Auto" mode.
• SPDIF Setup Page
•
Open S.l-channel output, enter "Test tone" mode which shall be executed
in "No disc" status, and then set
t •
SPDIF Setup
Output/Off Meaning that the output signal is an analog signal
SPIDF/RAW Meaning that the ture form source code flow of the DVD disc is delivered
directly through digital port
SPIDF/PCM Meaning that the code flow of the disc had been decoded before it was
encoded into the PCM digital signal output. That entry is selected when
the DVD audio output analog signal is connected with 2-channel digital
stereo amplifier.
LPCM Output
48K
It is available to convert 96 K LPCM digital audio into 48K LPCM
output when selecting LPCM as 48 K. (That entry is selected when your
power amplifier does not support 96K LPCM decoding.)
96K It is available to deliver the LPCM digital audio in true form output
when selecting LPCM96 K.
The setu of PCM
channe~nly
be carried out when ' •
t
• • "is set to be
"~"or
"Other". If the sampling rate of
LPCM of the disc is smaller than the sampling rate chosen, then the smaller
output is delivered (if the disc is 48 K, but the consumer's selection is 96K,
the actual output is 48 K)
Function
Post DRC
On/Off/Auto To set up the post DRC ratio of sound. It is suggested that the post
DRC is set up to "Auto" mode.
• SPDIF Setup Page
•
Open S.l-channel output, enter "Test tone" mode which shall be executed
in "No disc" status, and then set
t •
SPDIF Setup
Output/Off Meaning that the output signal is an analog signal
SPIDF/RAW Meaning that the ture form source code flow of the DVD disc is delivered
directly through digital port
SPIDF/PCM Meaning that the code flow of the disc had been decoded before it was
encoded into the PCM digital signal output. That entry is selected when
the DVD audio output analog signal is connected with 2-channel digital
stereo amplifier.
LPCM Output
48K
It is available to convert 96 K LPCM digital audio into 48K LPCM
output when selecting LPCM as 48 K. (That entry is selected when your
power amplifier does not support 96K LPCM decoding.)
96K It is available to deliver the LPCM digital audio in true form output
when selecting LPCM96 K.
The setu of PCM
channe~nly
be carried out when ' •
t
• • "is set to be
"~"or
"Other". If the sampling rate of
LPCM of the disc is smaller than the sampling rate chosen, then the smaller
output is delivered (if the disc is 48 K, but the consumer's selection is 96K,
the actual output is 48 K)
Function
Post DRC
On/Off/Auto To set up the post DRC ratio of sound. It is suggested that the post
DRC is set up to "Auto" mode.
• SPDIF Setup Page
•
Open S.l-channel output, enter "Test tone" mode which shall be executed
in "No disc" status, and then set
t •
SPDIF Setup
Output/Off Meaning that the output signal is an analog signal
SPIDF/RAW Meaning that the ture form source code flow of the DVD disc is delivered
directly through digital port
SPIDF/PCM Meaning that the code flow of the disc had been decoded before it was
encoded into the PCM digital signal output. That entry is selected when
the DVD audio output analog signal is connected with 2-channel digital
stereo amplifier.
LPCM Output
48K
It is available to convert 96 K LPCM digital audio into 48K LPCM
output when selecting LPCM as 48 K. (That entry is selected when your
power amplifier does not support 96K LPCM decoding.)
96K It is available to deliver the LPCM digital audio in true form output
when selecting LPCM96 K.
The setu of PCM
channe~nly
be carried out when ' •
t
• • "is set to be
"~"or
"Other". If the sampling rate of
LPCM of the disc is smaller than the sampling rate chosen, then the smaller
output is delivered (if the disc is 48 K, but the consumer's selection is 96K,
the actual output is 48 K)