Yamaha F150A Service Manual page 308

Index
E.
ECM ..........................................................1-17
Electrical .....................................................2-7
Electrical components.................................8-3
Electronic control system ..........................1-17
F.
Fail-safe control ........................................1-18
Features and benefits .................................1-6
Fire prevention ............................................1-3
Fuel and blowby hoses ...............................4-2
Fuel control system...................................8-15
Fuel filter, fuel pump, and intake silencer ...4-3
Fuel pump control .....................................1-20
Fuel system....................................... 1-15
G.
General .....................................................3-15
General specifications.................................2-1
General torques ........................................2-13
Good working practices ..............................1-4
H.
Hose routing................................................4-2
How to use this manual...............................1-1
I.
Identification................................................1-5
Ignition and ignition control system.............8-9
Installing the clamp brackets.....................7-18
Installing the cylinder head .......................5-35
Installing the drive shaft .................. 6-20
Installing the lower unit ................... 6-23
Installing the power trim and tilt unit..........7-44
Installing the power unit ............................5-55
Installing the pressure control valve..........5-37
Installing the propeller shaft
housing ......................................... 6-21
Installing the sprockets and timing belt .....5-21
Installing the steering arm.........................7-14
Installing the upper case ...........................7-15
Installing the valves...................................5-34
Installing the water pump and
shift rod ......................................... 6-21
Intake assembly and vapor separator.........4-9
Intake system..............................................1-9
Introduction .................................................9-2
Isolator ......................................................1-16
J.
Junction box assembly................................8-4
i-3
L.
Lower unit ..........................................2-6
Lower unit (counter rotation model).......... 6-32
Lower unit (regular rotation model)............. 6-4
Lubricating the outboard motor................. 3-16
Lubrication system.................................... 1-13
M.
Maintenance interval chart ......................... 3-2
Maintenance specification .......................... 2-3
Manual format............................................. 1-1
Measuring the forward and
reverse gear backlash ...................6-29
Measuring the fuel pressure ..................... 4-13
,
3-3 Measuring the lower resistance.................. 8-2
Measuring the peak voltage ....................... 8-2
O.
Over-revolution control ............................. 1-20
P.
Parts, lubricants, and sealants ................... 1-3
Piston and piston ring ................................. 1-7
Port view..................................................... 8-3
Power trim and tilt electrical system ......... 7-46
Power trim and tilt unit .....................3-13
Power unit............................ 2-3
Predelivery checks ................................... 1-22
Propeller selection .................................... 1-21
Propeller shaft housing
(counter rotation model) ......................... 6-38
Propeller shaft housing
,
6-49
(regular rotation model) .......................... 6-10
,
6-52
Propeller size............................................ 1-21
R.
Rectifier Regulator.................................... 1-16
,
6-49 Reducing the fuel pressure....................... 4-15
Refacing the valve seat ............................ 5-31
Removing the clamp brackets .................. 7-18
Removing the cylinder head ..................... 5-28
Removing the drive shaft.................6-17
Removing the exhaust cover .................... 5-37
,
6-50 Removing the lower unit ....................6-8
Removing the oil filter ............................... 5-20
Removing the power trim and tilt unit ....... 7-27
Removing the power unit.......................... 5-18
Removing the propeller shaft
housing assembly..........................6-12
Removing the reservoir ............................ 7-33
Removing the starter motor pinion ........... 8-22
,
3-13
,
6-60
,
7-20
, , ,
3-4 5-3 9-5
,
6-46
,
6-36
,
6-40
63P3F11