Page of 112
Download Table of ContentsContents Print This PagePrint Bookmark

Advertising

Advertising

Nokia 105s Gateway
Installation Guide
Part No. N450000309 Rev 001
Published August 2006

Advertising

   Related Manuals for Nokia 105s

   Summary of Contents for Nokia 105s

  • Page 1

    Nokia 105s Gateway Installation Guide Part No. N450000309 Rev 001 Published August 2006...

  • Page 2

    Rights clause at FAR 52.227-19. IMPORTANT NOTE TO USERS This software and hardware is provided by Nokia Inc. as is and any express or implied warranties, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose are disclaimed. In no event shall Nokia, or its affiliates, subsidiaries or suppliers be liable for any direct, indirect, incidental, special, exemplary, or consequential damages (including, but not limited to, procurement of substitute goods or services;...

  • Page 3

    #07-00 Alexandra Technopark email: info.ipnetworking_apac@nokia.com Singapore 119968 Nokia Customer Support Web Site: https://support.nokia.com/ Email: tac.support@nokia.com Americas Europe Voice: 1-888-361-5030 or Voice: +44 (0) 125-286-8900 1-613-271-6721 Fax: 1-613-271-8782 Fax: +44 (0) 125-286-5666 Asia-Pacific Voice: +65-67232999 Fax: +65-67232897 050602 Nokia 105s Gateway Installation Guide...

  • Page 4

    Nokia 105s Gateway Installation Guide...

  • Page 5: Table Of Contents

    System Status LEDs ........23 Managing the 105s Gateway ......24 Site Requirements, Warnings, and Cautions .

  • Page 6: Table Of Contents

    Using a Console Connection ......40 Using Nokia Network Voyager ......43 Viewing Nokia IPSO Documentation by Using Nokia Network Voyager .

  • Page 7: Table Of Contents

    Index ..........109 Nokia 105s Gateway Installation Guide...

  • Page 8

    Nokia 105s Gateway Installation Guide...

  • Page 9

    Table 2 Text Conventions ......16 Table 3 Specifications for the 105s Gateway ....20 Table 4 PMC Network Interface Card Slots .

  • Page 10

    Nokia 105s Gateway Installation Guide...

  • Page 11

    Figure 7 Back Panel Power Switch and Socket ... . . 32 Figure 8 Nokia Network Voyager Reference Access Points ..45 Figure 9 Four-Port Ethernet NIC Front Panel Details ..60 Figure 10 Output Connector for the Ethernet Cable .

  • Page 12

    Nokia 105s Gateway Installation Guide...

  • Page 13: About This Guide

    About this Guide This guide describes how to install and use Nokia 105s gateways. Installation and maintenance should be performed by experienced technicians or Nokia- approved service providers only. This preface provides the following information: In this Guide Conventions this Guide Uses...

  • Page 14: Conventions This Guide Uses

    Warnings advise the user that bodily injury might occur because of a physical hazard. Caution Cautions indicate potential equipment damage, equipment malfunction, loss of performance, loss of data, or interruption of service. Note Notes provide information of special interest or recommendations. Nokia 105s Gateway Installation Guide...

  • Page 15: Command-line Conventions

    This required element is usually the product name or other short word that invokes the product or calls the compiler or preprocessor script for a compiled Nokia product. It might appear alone or precede one or more options. You must spell a command exactly as shown and use lowercase letters.

  • Page 16: Text Conventions

    Log error 12453 Indicates text you enter or type, for example: bold monospace font # configure nat Key names Keys that you press simultaneously are linked by a plus sign (+): Press Ctrl + Alt + Del. Nokia 105s Gateway Installation Guide...

  • Page 17: Related Documentation

    • Indicates a variable in a command: if_name delete interface Related Documentation You can find this guide in PDF on the Nokia support Web site (https:// support.nokia.com/) and on the Nokia IPSO operating system CD-ROM issued with your Nokia 105s gateway.

  • Page 18

    NSAS you are using Nokia 105s Information Sheet You can find the most up-to date version of the Nokia 105s Gateway Installation Guide and other documents in the preceding list in PDF on the Nokia support site (https://support.nokia.com). You can access inline help, the Nokia Network Voyager Reference Guide, and the CLI Reference Guide from Nokia Network Voyager.

  • Page 19: Overview

    Users can access enterprise resources from any Web-capable platform and location. The small size of the 105s gateway makes it ideal for installations that need to conserve space. As network devices, 105s gateways support a comprehensive suite of IP-routing functions and protocols, including RIPv1/RIPv2, IGRP, OSPF and BGP4 for unicast traffic, and DVMRP for multicast traffic.

  • Page 20

    • Two or fewer two-port copper Gigabit Ethernet NICs (NICs) support • Two or fewer two-port fiber-optic Gigabit Ethernet NICs The following figures show component locations for the Nokia 105s gateway. Figure 1 Component Locations Front View System status LEDs PMC NIC slots (slots 1 and 2)

  • Page 21: Built-in Gigabit Ethernet Ports

    About the Nokia 105s Gateway Figure 2 Component Locations Rear View Power switch 00527 Power socket Built-In Gigabit Ethernet Ports The four built-in Gigabit Ethernet ports are located on the front of the gateway. Figure 3 shows the layout of the built-in Gigabit Ethernet ports and status LEDs.

  • Page 22: Pmc Expansion Slots

    Nokia recommends the use of shielded twisted-pair cables and connectors for best Electromagnetic Interference and Immunity performance. PMC Expansion Slots The 105s gateway provides two additional PMC network interface card (NIC) slots, as described in Table Table 4 PMC Network Interface Card Slots Interface For details, see...

  • Page 23: System Status Leds

    About the Nokia 105s Gateway System Status LEDs You can monitor the basic operation of the 105s gateway and NICs by checking their status LEDs. The system status LEDs are located on the front panel of the gateway, as Figure 4 shows.

  • Page 24: Managing The 105s Gateway

    100 Mbps Ethernet NICs” on page 59. Managing the 105s Gateway You can manage the 105s gateway by using one of the following interfaces: Nokia Network Voyager—an SSL-secured, Web-based element management interface to Nokia gateways. Network Voyager is preinstalled on the 105s gateway and enabled through the IPSO operating system.

  • Page 25

    Caution For 105s gateways intended for shipment outside of the United States, the cord might be optional. If a cord is not provided, use a power cord rated at 6A, 250V, maximum 15 feet long, made of HAR cordage and IEC fittings approved by the country of end use.

  • Page 26: Software Requirements

    Overview Software Requirements The Nokia 105s gateway supports the following operating system and applications: Nokia operating system software requirements—IPSO v4.1 or later Nokia Secure Access System (NSAS) 3.3.4 or later For information about updates to the software requirements or additional...

  • Page 27

    The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-of-life. This applies to your device but also to any enhancements marked with this symbol. Do not dispose of these products as unsorted municipal waste. Nokia 105s Gateway Installation Guide...

  • Page 28

    Overview Nokia 105s Gateway Installation Guide...

  • Page 29: Installing The Nokia 105s Gateway

    Installing the Nokia 105s Gateway This chapter describes how to install the Nokia 105s gateway. The following topics are covered: Before You Begin Rack Mounting the Gateway Connecting Power Connecting to the Console or Auxiliary Port Connecting to Network Interfaces...

  • Page 30: Rack Mounting The Gateway

    Rack Mounting the Gateway The 105s gateway mounts in a standard 19-inch rack with four mounting screws as Figure 5 shows.

  • Page 31: Connecting Power

    Caution Blocking ventilation openings during installation may result in damage to the gateway. Connecting Power The power plug and power switch for the 105s gateway is located on the back of the gateway, as Figure 7 shows. Nokia 105s Gateway Installation Guide...

  • Page 32: Connecting To The Console Or Auxiliary Port

    Connecting to the Console or Auxiliary Port If you do not use DHCP to perform the initial configuration of your Nokia 105s gateway, you must use a serial console connection (RJ-45 null-modem cable included). For information about using DHCP for initial configurations, Chapter 3, “Performing the Initial Configuration.”...

  • Page 33

    2. Connect the other end of the cable to the VT100 console or to a system running a terminal-emulation program. The cable that Nokia provides with 105s gateways includes a latching mechanism used to secure the cable to the console port or auxiliary port of your gateway.

  • Page 34

    Installing the Nokia 105s Gateway Note To use the cable for modem connections from the auxiliary port, you need to order a modem cable kit. For information about contacting Nokia to order the kit, see “Nokia Contact Information” on page 3.

  • Page 35: Console Port

    (using the gateway console port and the DB-9 female adaptor) or to a DB-25 modem connection (using the gateway auxiliary port and the DB-25 male adaptor). The DB-9 adapter is provided with the cable. The DB-25 adaptor is provided with Nokia modem cable kits for the 105s. 00552 DB-25 male adapter...

  • Page 36: Auxiliary Port

    RJ-45 Pin DB-9 Pin Signal The console cable provided with the 105s is comprised of two parts: 6-foot rollover cable with RJ-45 terminations RJ-45 to DB-9 adapter On the opposite end of the console cable, connect the RJ-45 to the DB-9 adapter, which you can then connect to the host terminal.

  • Page 37: Connecting To Network Interfaces

    Use a straight-through RJ-45 cable to connect to a 10-Mbps or 100-Mbps hub. Use a crossover RJ-45 cable to connect directly to a host. For details, see “Ethernet NIC Connectors and Cables” on page 61. Nokia 105s Gateway Installation Guide...

  • Page 38

    100-Mbps, or 1000-Mbps hub or directly to a host. Note All Nokia copper Gigabit Ethernet NICs support cable auto-sensing. You can use a straight-through or crossover cable to connect the NIC to a Gigabit Ethernet hub or switch, or to connect directly to a host.

  • Page 39: Performing The Initial Configuration

    Performing the Initial Configuration The first time you turn power on to a Nokia 105s gateway, the initial configuration process begins. This process enables you to configure the network settings and provides access to the admin account. You can perform the initial configuration in two ways.

  • Page 40: Using A Console Connection

    What is the default router? What is the interface speed? Note The default interface speed for the 105s is 1000 Mbps. You can make VLAN, SNMP community string, and remote logging configuration choices at this time, although you can change them later.

  • Page 41

    The fans on the back of the gateway turn on when you press the power switch. Verify that the fans are running after you press the switch. Check the power LED on the front panel of the gateway (the Nokia logo) to ensure that the power supply is operating correctly. The power LED should be illuminated.

  • Page 42

    If you verify the console connections and still do not see either the BOOTMGR> or Hostname? prompts, verify that the terminal or terminal emulator program settings are correct. If the settings are correct, contact your Nokia service provider as listed in “Nokia Contact Information”...

  • Page 43: Using Nokia Network Voyager

    Using Nokia Network Voyager Using Nokia Network Voyager Use Nokia Network Voyager to configure and monitor your gateway. For additional information about how to use Network Voyager, see “Viewing Nokia IPSO Documentation by Using Nokia Network Voyager” later in this section.

  • Page 44: Voyager

    You do this be navigating to Configuration > System Configuration > Packages > Manage Packages and turning the package on. The following documentation is available in Nokia Network Voyager and is accessible from the Network Voyager interface, as shown in Figure Nokia Network Voyager Reference Guide—This guide is the...

  • Page 45: Using The Command-line Interface

    Link to inline help (context sensitive help) Using the Command-Line Interface You can also use the Nokia IPSO command-line interface (CLI) to manage and configure 105s gateways from the command line. Everything that you can accomplish with Network Voyager you can also do with the CLI.

  • Page 46

    That is, you can view configuration settings, but you cannot change them. You can now execute CLI commands from the CLI shell and the Nokia IPSO shell. The Nokia IPSO shell is what you see when you initially log on to the gateway. Execute from...

  • Page 47

    Using the Command-Line Interface For more information about how to access and use the CLI, see the Nokia CLI Reference Guide for the version of Nokia IPSO you are using. 060228 Nokia 105s Gateway Installation Guide...

  • Page 48

    Performing the Initial Configuration Nokia 105s Gateway Installation Guide...

  • Page 49: Installing And Replacing Network Interface Cards

    Chapter 5, “Connecting PMC Network Interface Cards.” Caution You should have a working knowledge of networking equipment before attempting to service a 105s gateway. Limit service of the unit to the procedures described in this chapter. Nokia 105s Gateway Installation Guide...

  • Page 50: Deactivating Configured Interfaces

    NIC in Network Voyager. For additional information, see “Deactivating Configured Interfaces” on page 50. Use these instructions to remove, install, or replace a NIC in the 105s gateway. Some steps are not applicable to all procedures. The instructions point out steps appropriate to each procedure.

  • Page 51: Before You Start

    Removing, Installing, and Replacing NICs Before You Start To remove, install, or replace a Nokia NIC, you need the following: A Phillips-head screwdriver Physical access to the gateway Access to the gateway by using Nokia Network Voyager or the CLI...

  • Page 52

    2. Use your fingers or a screwdriver to loosen the retaining screws that hold the chassis tray assembly. 00525gen Chassis tray assembly retaining screws 3. Gently pull the chassis tray assembly forward to expose the NIC connectors. Remove the tray completely to avoid damaging components. 00537gen Nokia 105s Gateway Installation Guide...

  • Page 53

    5. From above the chassis tray assembly, remove the NIC retaining screws from the back of the NIC. 00530 Nokia 105s Gateway Installation Guide...

  • Page 54

    Note To reduce electromagnetic interference (EMI), a blank bezel needs to be installed in the place of any NIC you have removed. b. Proceed to step Nokia 105s Gateway Installation Guide...

  • Page 55

    Make sure that the NIC edge is completely seated into the connectors on the chassis tray assembly. 8. From the top of the chassis tray assembly, screw the NIC retaining screws into the standoffs on the back of the NIC. 00531 Nokia 105s Gateway Installation Guide...

  • Page 56

    9. From beneath the chassis tray assembly, screw in the bezel retaining screws. 00528 10. Slide the chassis tray assembly back into the gateway until it clicks into place. 00538gen The gateway automatically restarts when the chassis tray assembly clicks into place. Nokia 105s Gateway Installation Guide...

  • Page 57: Configuring And Activating Interfaces

    00525gen Chassis tray assembly retaining screws Configuring and Activating Interfaces The 105s gateway automatically detects any new NIC when the gateway is restarted. Use Network Voyager to configure and activate the logical and physical interfaces on the NIC. For information about how to access Network Voyager and the related reference materials, see “Using Nokia Network Voyager”...

  • Page 58

    Use Network Voyager to access detailed port information. For information about accessing Network Voyager, see “Using Nokia Network Voyager” page 43. You can also use the Nokia IPSO tcpdump command to examine the track on a specific port. Nokia 105s Gateway Installation Guide...

  • Page 59: Connecting Pmc Network Interface Cards

    Connecting PMC Network Interface Cards This chapter describes the PMC network interface cards (NICs) available for the 105s gateway and describes how to connect those NICs to your network. The following NICs are covered: Four-Port 10/100 Mbps Ethernet NICs Two-Port Copper Gigabit Ethernet Network Interface Card...

  • Page 60: Ethernet Nic Features

    Connecting PMC Network Interface Cards When you purchase an Ethernet NIC with your 105s gateway, the NIC is installed before the gateway is delivered to you. For information on how to add or replace a NIC later, see Chapter 4, “Installing and Replacing Network Interface Cards.”...

  • Page 61: Ethernet Nic Connectors And Cables

    Figure 10 shows the pin assignments for the cable. The RJ-45 cable output connector is numbered from right to left, with the copper tabs facing up and toward you. Nokia 105s Gateway Installation Guide...

  • Page 62

    RJ-45 cross-over cable. Figure 11 Ethernet Crossover-Cable Pin Connections 00017.1 You can also use cables intended for Gigabit Ethernet NIC connections for your Ethernet NIC connections, as shown in Figure Nokia 105s Gateway Installation Guide...

  • Page 63: Two-port Copper Gigabit Ethernet Network Interface Card

    Two-Port Copper Gigabit Ethernet Network Interface Card All NICs installed in a 105s are installed into slots on the gateway. Gigabit Ethernet NICs can occupy any of the slots or subslots in a gateway that other NICs do not occupy.

  • Page 64: Copper Gigabit Ethernet Connectors And Cables

    Figure 13 shows the front panel details for the two-port copper Gigabit Ethernet NIC you use in the Nokia 105s gateway. Figure 13 Two-Port Copper Gigabit Ethernet NIC Link LED (solid yellow for 10/100 Mbps, solid green for 1000 Mbps)

  • Page 65

    Assignment BI_DA+ 00270 BI_DA- BI_DB+ BI_DC+ BI_DC- BI_DB- BI_DD+ BI_DD- To connect directly to a host, use an RJ-45 crossover cable wired as Figure 15 shows. Figure 15 Gigabit Ethernet Crossover Cable Pin Connections 00020 Nokia 105s Gateway Installation Guide...

  • Page 66: Two-port Fiber-optic Gigabit Ethernet Network Interface Card

    Two-Port Fiber-Optic Gigabit Ethernet Network Interface Card All NICs installed in a 105s are installed into slots on the gateway. Gigabit Ethernet NICs can occupy any of the slots or subslots in a gateway that other NICs do not occupy.

  • Page 67: Fiber-optic Gigabit Ethernet Connectors And Cables

    You can also use a half-duplex LC-to-LC cable to loop back the transmit port of an interface to the receiver port. Two LC-to-SC cables are included with two-port fiber-optic Gigabit Ethernet NICs. You can order additional cables from a cable vendor of your choice. Nokia 105s Gateway Installation Guide...

  • Page 68

    Connecting PMC Network Interface Cards Nokia 105s Gateway Installation Guide...

  • Page 69: Installing And Replacing Other Components

    Installing and Replacing Other Components This chapter provides information on how to add or replace user serviceable items other than network interface cards (NICs) in your 105s gateway. The following topics are covered: Installing or Replacing a Hard-Disk Drive Replacing or Upgrading Memory...

  • Page 70: Installing Or Replacing A Hard-disk Drive

    Installing and Replacing Other Components Installing or Replacing a Hard-Disk Drive You can add a single hard-disk drive to your 105s gateway. The following figure shows the location of the hard-disk drive on the motherboard. Note Back up your files to a remote system on a regular basis. For back up and restore procedures, see the Getting Started Guide and Release Notes for the version of Nokia IPSO you are using.

  • Page 71

    1. Use Network Voyager to shut the gateway down. For information about how to access Network Voyager, see “Using Nokia Network Voyager” on page 43. 2. Loosen the retaining screws that hold the chassis tray assembly. 00525gen Chassis tray assembly retaining screws Nokia 105s Gateway Installation Guide...

  • Page 72

    00537gen Note Because power to a 105s gateway is automatically disconnected when the chassis tray assembly is opened, you do not need to manually disconnect the power for this procedure. Any servicing of the unit, however, should be completed with the chassis tray assembly fully removed from the gateway.

  • Page 73

    4. If a you are replacing a hard-disk drive, remove the retaining screws that hold the hard-disk drive unit from the bottom of the chassis tray assembly. 00534 Gently remove the hard-disk drive from the motherboard, taking care not to damage the connector. Nokia 105s Gateway Installation Guide...

  • Page 74

    Installing and Replacing Other Components 5. Insert the hard-disk drive unit. 00536 Note Push the hard-disk drive gently into place. Take care to align the connectors correctly as the connectors are not keyed. Nokia 105s Gateway Installation Guide...

  • Page 75

    6. Tighten the retaining screws that holds the hard-disk drive into place. 00535 7. Slide the chassis tray assembly back into the gateway until it clicks into place. 00538gen The gateway automatically restarts when the chassis tray assembly clicks into place. Nokia 105s Gateway Installation Guide...

  • Page 76: Replacing Or Upgrading Memory

    00525gen Chassis tray assembly retaining screws Replacing or Upgrading Memory The 105s gateways have two dual inline memory-module (DIMM) sockets. This section explains how to upgrade or replace the memory in your gateway by using a Nokia-approved memory upgrade kit.

  • Page 77

    Nokia memory upgrade kit and accompanying documentation Network or console access to the gateway Caution To protect the 105s gateway and the memory modules from electrostatic discharge (ESD), make sure you are properly grounded before you touch these components. Nokia 105s Gateway Installation Guide...

  • Page 78

    00525gen Chassis tray assembly retaining screws Note Because power to a 105s gateway is automatically disconnected when the chassis tray assembly is opened, you do not need to manually disconnect the power for this procedure. Any servicing of the unit, however, should be completed with the chassis tray assembly fully removed from the gateway.

  • Page 79

    You might need to pull opposite ends of the DIMM alternately to gradually free it from the contact pins. 5. The memory DIMMs are keyed to prevent improper insertion. Press the new DIMM into the socket until it clicks into place. Nokia 105s Gateway Installation Guide...

  • Page 80

    Be sure the contacts and slots are properly aligned before you insert the DIMM. 00544gen The retaining clips move into the lock position as you press the DIMM into place. Nokia 105s Gateway Installation Guide...

  • Page 81

    Network Voyager, the CLI, or the IPSO shell. To verify the memory from the CLI, enter: show asset hardware To verify the memory from the IPSO shell, enter: dmesg | grep ‘real memory’ Nokia 105s Gateway Installation Guide...

  • Page 82: Replacing The Battery

    Installing and Replacing Other Components Replacing the Battery To replace the battery, you need the following: The appropriate Nokia battery replacement kit for your gateway Physical access to the gateway A Phillips-head screwdriver A grounding wrist strap (Optional) Safety glasses Warning An explosion might occur if the battery is incorrectly placed.

  • Page 83

    00525gen Chassis tray assembly retaining screws Note Because power to an 105s gateway is automatically disconnected when the chassis tray assembly is opened, you do not need to manually disconnect the power for this procedure. Any servicing of the unit, however, should be completed with the chassis tray assembly fully removed from the gateway.

  • Page 84

    Replace the battery only with the same or equivalent type battery recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. 6. With the positive side facing up, slide the new battery through the cutout in the battery holder. Nokia 105s Gateway Installation Guide...

  • Page 85

    The gateway automatically restarts when the chassis tray assembly clicks into place. 8. Resecure the two retaining screws. 00525gen Chassis tray assembly retaining screws After you replace the battery, you need to reset the date and time using Network Voyager or the CLI. Nokia 105s Gateway Installation Guide...

  • Page 86

    Installing and Replacing Other Components Nokia 105s Gateway Installation Guide...

  • Page 87: Troubleshooting

    105s gateway. If this is not possible using your laptop computer or terminal, the problem is with the terminal or cable and not the gateway.

  • Page 88

    Solution Verify terminal settings: 8 data, 1 stop, no parity, 9600 bps. Problem Terminal set for flow control. Solution The 105s gateway does not use flow control. The terminal should be set for no flow control. Problem Defective 105s gateway or file system.

  • Page 89

    The two double quotation marks at the end of the command properly indicate a blank password. After you execute this command, the system reports that the password was not successfully changed. However, the password is changed and is now newpassword. Nokia 105s Gateway Installation Guide...

  • Page 90

    Chapter 3, “Performing the Initial Configuration”. To reset the default database settings 1. Log in to the 105s gateway as admin by using Network Voyager. For information about how to access Network Voyager and the related reference materials, see “Using Nokia Network Voyager”...

  • Page 91

    Do Not See Interfaces that Should be Present Problem Local 105s gateway ports do not appear. Solution Your NIC might be defective. Contact the appropriate Nokia customer support site as listed in “Nokia Contact Information”...

  • Page 92

    Device Problem No link light. Solution You might have used the wrong cable. Use a crossover cable between a 105s gateway and a host, and a straight-through cable between a gateway and a hub. Problem Solid data and activity LED.

  • Page 93

    4. Click Delete for the entry you want to delete. 5. Click Apply. Problems with Multicast Use tcpdump to view packets. To display packets for a specific interface, use the following command: tcpdump . For more -i interface proto igmp Nokia 105s Gateway Installation Guide...

  • Page 94

    Troubleshooting information about how to use the tcpdump command, see the Nokia Network Voyager Reference Guide. Under Routing Options in the Routing Configuration section in Network Voyager, you can also enable several types of trace options for DVMRP. These traces are logged into /var/tmp/ipsrd.log...

  • Page 95

    Problem The MTU size is not 1500 (for Ethernet interfaces) or 16018 (for Gigabit Ethernet interfaces). Solution The MTU size must be 1500 (for Ethernet interfaces) or 16018 (for Gigabit Ethernet interfaces). Nokia does not support larger MTU sizes. Gateway Not Receiving Power Problem Power cord is not properly plugged in.

  • Page 96

    Troubleshooting Gateway locks up after you upgrade Nokia IPSO with a console connection. No error messages appear, but the gateway stops responding to console and network. Problem During the upgrade process, some of the environment variables might not have updated correctly.

  • Page 97: Troubleshooting Routing Problems

    ICLID (IPSRD command-line interface daemon) command. An example use of the ICLID command is shown below. For information about the ICLID command, see the Nokia Network Voyager Reference Guide. For information about how to access Network Voyager and the related reference materials, see “Using Nokia Network Voyager”...

  • Page 98

    Network Voyager. When a trace is enabled the output appears in /var/tmp/ipsrd.log. Common Problems with OSPF Use tcpdump to view routing information. Use the following command display routing updates for that interface: tcpdump -i interface proto ospf Nokia 105s Gateway Installation Guide...

  • Page 99

    Troubleshooting Routing Problems For more information about how to use the tcpdump command, see the Nokia Network Voyager Reference Guide. Under routing options in Network Voyager, you can also enable several types of trace options for OSPF. These traces are logged in /var/tmp/ipsrd.log...

  • Page 100

    Troubleshooting For more information about how to use the tcpdump command, see the Nokia Network Voyager Reference Guide. Under routing options in Network Voyager, you can also enable several types of trace options for routing information protocol (RIP). These traces are logged in /var/tmp/ipsrd.log...

  • Page 101

    Troubleshooting Routing Problems Problem Routing protocol is not functioning properly. Solution to ensure that each routing protocol is functioning properly, see “Common Problems with OSPF” on page 98 and “Common Problems with RIP” on page 99. Nokia 105s Gateway Installation Guide...

  • Page 102

    Troubleshooting Nokia 105s Gateway Installation Guide...

  • Page 103: A Technical Specifications

    1.75 inches (4.45 centimeters) of vertical space 18 inches (46 centimeters) behind the front-panel of the rack 6 inches (15 centimeters) behind the 105s gateway to allow the back exit fan to move air through the gateways Nokia 105s Gateway Installation Guide...

  • Page 104: Operating Temperature

    Do not place objects over the ventilation holes on the gateway. The gateway might overheat and become damaged. Operating Temperature The operating temperature range for the Nokia 105s gateway is 0° C to 45° C (32° F to 113° F). NIC Interfaces...

  • Page 105: B Compliance Information

    Declaration of Conformity According to ISO/IEC Guide 22 and EN 45014: Manufacturer’s Name: Nokia Inc. Manufacturer’s Address: 313 Fairchild Drive Mountain View, CA 94043-2215 declares that the product: Product Name: 105s Model Number: EM7500 Product Options: Nokia 105s Gateway Installation Guide...

  • Page 106

    Directive 89/336/EEC with Amendment 93/68/EEC. Christopher Saleem Compliance & Reliability Engineering Manager Security & Mobile Connectivity, Enterprise Solutions Mountain View, California May 2006 Tom Furlong Vice President and General Manager Security & Mobile Connectivity, Enterprise Solutions Mountain View, CA Nokia 105s Gateway Installation Guide...

  • Page 107: Compliance Statements

    European Community (CE) Immunity Standards EN55024 European Community (CE) EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-11 Harmonics and Voltage Fluctuation EN61000-3-2 European Community (CE) EN61000-3-3 European Community (CE) Safety Standards UL60950/EN60950 US/European Community(CE) CAN/CSA-C22.2 No.60950 Canada Nokia 105s Gateway Installation Guide...

  • Page 108: Fcc Notice (us)

    Consult the dealer or an experienced radio/TV technician for help. Caution Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. 060425 Nokia 105s Gateway Installation Guide...

  • Page 109: Index

    NICs 50 compliance information 105 declaration of conformity 105 declaration of conformity 105 depth specification 103 FCC notice 108 DHCP server 39 compliance statements 107 DIMMs component locations 20 socket locations 77 Nokia 105s Gateway Installation Guide Index - 109...

  • Page 110

    Gigabit Ethernet, fiber-optic 67 height specification 103 installing 49, 50 interface specifications 104 specifications 20, 104 ICLID command Nokia IPSO troubleshooting with the 97 command-line interface (CLI) 24, 45 reference documentation 44 requirements 26 Index - 110 Nokia 105s Gateway Installation Guide...

  • Page 111

    25 replacing RAM memory 76 RJ-45 connector console cables, for 36 weight specification 103 crossover cables, for 62 width specification 103 Ethernet cables, for 61 serial port 36 space requirements 103 Nokia 105s Gateway Installation Guide Index - 111...

  • Page 112

    Index - 112 Nokia 105s Gateway Installation Guide...

Comments to this Manuals

Symbols: 0
Latest comments: