Table of Contents
Advertisement
1
GSM/GPRS/GPS Tracker
User Manual
Preface
Thank you for purchasing the tracker. This manual shows how to operate the device smoothly
and correctly. Make sure to read this manual carefully before using this product. Please note
that specification and information are subject to changes without prior notice in this manual.
Any change will be integrated in the latest release. The manufacturer assumes no
responsibility for any errors or omissions in this document.
Advertisement
Table of Contents
Related Manuals for GPS Tracker GPS303CD
Summary of Contents for GPS Tracker GPS303CD
- Page 1 GSM/GPRS/GPS Tracker User Manual Preface Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual.
-
Page 2: Table Of Contents
Contents 1. Summary ................................4 2. Applications ................................ 4 3. Hardware Description ............................4 4. Accessories ................................. 5 5. Specifications ..............................5 6. Usage ................................6 6.1 Terminal Installation ............................. 6 6.2SIM CARD Installations..........................7 6.3 Turn on the Tracker Device.......................... 7 6.4 GSM/GPS LED Indicator .......................... - Page 3 6.25 Alarms under Arm State ..........................22 6.25.1 ACC alarm ............................22 6.25.2 Shock Sensor alarm ........................... 22 6.26 Alarm without GSM network service ....................... 23 6.27 Sleep Mode ............................23 6.27.1 Sleep by time ............................. 23 6.27.2 Sleep by shock sensor ........................23 6.27.3 Deep Sleep by Shock Sensor ......................
-
Page 4: Summary
1. Summary This tracker is based on the GSM / GPRS network and GPS satellite positioning system, which sets multiple functions of security, positioning, monitoring surveillance, emergency alarms and tracking in its entirety. It can track and monitor remote target by SMS or internet. 1.2 Features 1.2.1 IP Rating: IP66 1.2.2Internal GPS&GSM antenna, compact, elegant appearance... -
Page 5: Accessories
GPS/POWER/GSM Indicator 4. Accessories Type D: Add remote controller to ARM & DISARM on the basis of type C Applicable photo Name Specifications model Harness 8PIN Standard Relay 12V/40A or 24V/40A Standard Small alarm 12V/24V Optional siren Remote Optional for Controller type D 5. -
Page 6: Usage
8.9×5.0×1.6cm Weight Network GSM/GPRS Band 850/900/1800/1900Mhz -159dBm sensitivity accurancy Cold status 45s GPS start time Warm status 35s Hot status 1s Car power 12 V -24V supply Back up Chargeable 3.7V 500mAh Polymer Li-Battery battery Storage Temp -40° C to +85° C Operation -20°... -
Page 7: Sim Card Installations
Wiring diagram 6.2SIM CARD Installations 6.2.1 Use the screwdriver accompanied with the device to open sealed buckle and insert the SIM card.If need data logging function, please insert microSD and put sealed buckle back 6.2.2Please make sure the SIM card is for GSM network and able to execute the function of incoming calls display, no calls can be diverted and the PIN code is locked. -
Page 8: Change Password
6.6 Change Password 6.6.1 Send SMS “password+old password+space+new password” to the unit to change the password. For example: send SMS “password123456 888888” to the unit. If succeeded, “password ok” will reply to your cell phone from the device tracker. 6.6.2 Be sure to keep the new password in mind, you have to upload the software to restore the original setting in case of losing the new password. -
Page 9: Single Locating
will reply “admin ok!” in SMS. 6.7.3 Delete authorization Send SMS：“noadmin+password+space+authorized number” to delete the authorized number. 6.7.4 If you want to track the target when it enters into another country, you must add the country code before the cell phone number. You should authorize your number in international format as follows: “admin123456 008613322221111”... -
Page 10: Auto Track Continuously
6.9 Auto track continuously 6.9.1 Track with limited times upon time interval: Send SMS command “fix030s005n +password” to the tracker device, it will report the latitude & longitude at intervals of 30 seconds for 5 times. (s:second, m:minute, h:hour). This command set must be in 3 digits and the maximum value is 255. -
Page 11: Turning Points Update Automatically
6.10 Turning points update automatically 6.10.1 The tracker will update the positions automatically to web server once the vehicle changing driving direction over pre set angle value to form a smooth trajectory consistent with the actual road, this function is only effective in GPRS mode. -
Page 12: Location Based Service (Lbs) / Cell-Id Locating
user name and password for GPRS login.) 6.12.2 After configure the APN, send "address+password" to device, it will reply SMS including real street/address name. For example: No.113, Guankou 2nd Rd, Nantou, Nanshan district, Shenzhen, Guangdong, china. e.g. address123456 6.13 Location based service (LBS) / Cell-ID locating If the tracker cannot establish a solid GPS Fix, it will calculate its location using Cell-ID GSM locating, Location reports will include the GPS coordinates of the last known positions as well as a LAC code to the “Manual Track”... -
Page 13: Data Logging
6.15.Data logging 6.15.1 When the tracker device loses GSM signals or fall offline from GPRS, tracker will store the tracking position and alerts automatically upon the pre-set condition, when GSM signals get back, all the event alerts will be auto-sent to the authorized numbers or monitoring platform (server), but the stored tracking data should be loaded to the monitoring platform via SMS command. -
Page 14: Forward The Third Parties' Message
Specified date Load： Send SMS: “load+ password+ space+ year month 6.16.2 date” to tracker device, it will reply: “load ok” .For Example: send SMS: “load123456 20110425” to the tracker device, means to load the tracking data of 25th April 2011 to monitoring platform. 6.17. -
Page 15: Alarm Function
function works. Received and execute Send ye out to 10086 balance123456 10086 ye Mobile Tracker 10086(China mobile) Send balance back Forward balance message to mobile Received ye from number in Received Balance message phone the tracker and process 6.19. Alarm Function 6.19.1 Low battery alarm Send SMS “lowbattery+password+space+on”, it will send SMS “low 6.19.1.1. -
Page 16: Sos
6.19.4 SOS Long Press the SOS button for 3 seconds （ For model D, press button on remote controller for 3 seconds）, the tracker device will send SMS “help me!+lat./long.” to all the authorized numbers at interval of 3 minutes. It will stop sending such alert SMS when any authorized number reply SMS “help me”... -
Page 17: Multi-Area Management
6.19.6 Multi-area management 6.19.6.1 Set Area Send SMS command "area+password+space+latitude,longitude+space+areaname,distanceM" to tracker(distance unit: M for meter, K for kilometer), it will reply "area01 ok". Example: Send "area123456 22.353648,113.543678 school,800M". Note: 5 areas at most and the distance between two points can't be less than the total distance in the 2 commands, and different areas can't cover each other. -
Page 18: Movement Alarm
name+latitude & longitude" to all the authorized phone number, and send same SMS when goes out of the area. Deactivate Multi-area management 6.19.6.5 Send SMS command "area+password+space+off" to tracker, it will reply"area off ok!" 6.19.7 Movement alarm Set up: when the unit stays immobile in a place for 3-10 minutes with 6.19.7.1. -
Page 19: Acc Working Alarm
Cancel: Send SMS “nospeed+password” to deactivate the overspeed alarm. Remark: The recommended speed should be not less than 30km/h. For below that rate, it will be effected the accuracy by GPS signals drift etc. 6.19.9 ACC working alarm This function is disabled as default. To active this function, send 6.19.9.1 "ACC+password"... -
Page 20: Function Of Remote Controller (Option For Model D )
after “stop” command, instead, will reply “it will be executed after speed less than 20KM/H”, and stop the car when the speed is less than 20KM/H 6.20.3 Resume the Oil and Power System send “resume+password" to tracker, it will reply "Resume engine succeed", that means vehicle has resume the oil supply. -
Page 21: Silent Mode
Press button on the remote controller for 0.5 seconds, the car enters armed state and the siren will beep one time, no SMS reply. If the car is in ignition (ACC is at “ON” position), then the car can’t enter ARM state, and siren keep silent. -
Page 22: Alarms Under Arm State
6.25 Alarms under Arm State 6.25.1 ACC alarm The unit will send SMS “ACC alarm+lat/long” to the authorized number at interval of 3 minutes when the engine of the car is turned on, that is the key is rotated to ACC.ON position to start the car in arm state; Siren will sound for 20 seconds, and repeat again after stop 20 seconds , send “disarm+password”... -
Page 23: Alarm Without Gsm Network Service
seconds, send command" sensitivity+password+space+3". 6.26 Alarm without GSM network service When the car is in the place without GSM network service, siren will sound under non-silent mode if alarm is triggered (sensor, ACC), but no SMS alarm will be sent to authorized number. 6.27 Sleep Mode 6.27.1 Sleep by time Send SMS command "sleep+password+space+time"... -
Page 24: Deep Sleep By Shock Sensor
e.g. sleep123456 shock 6.27.3 Deep Sleep by Shock Sensor Send "sleep+password+space+deepshock", tracker will reply "sleep deepshock ok" it will enter sleep mode if no vibration detecting, Tracker will be in super low power consumption status with GPS & GSM module shut off, and LED off. Calling or SMS can’t awake the tracker .Alarms can be triggered and work normally. -
Page 25: Check Imei
6.29 Check IMEI Send SMS command "imei+password" to the unit. E.g. Send SMS command "imei123456" to the tracker device, an IMEI number of 15 digits will reply to your cell phone. 6.30 Check the Vehicle State Send SMS command “check+password” to the tracker device in the vehicle, It will reply the status of the power, battery, GPS&GSM signal, GPRS status. -
Page 26: Tcp / Udp Switch
Send command:"gprs+password,1,1" switch to UDP mode. 6.34 Configure parameters by USB Connect the gps tracker to computer with the optional USB cable, find gps tracker’s internal memory and open serial debugging tool the format of text, edit the commands according to the tips. . -
Page 27: Gprs User Id And Password Setup
GPRS network operator. Text the tracker a SMS “APN+password + Space + your local APN” via 6.35.1.2 a cell phone and if setup successfully, the tracker will return the message “APN OK”. e.g. send SMS command “APN123456 CMNET”. If succeeded, “APN 6.35.1.3 OK”... -
Page 28: Switch To Gprs Mode
Address + Space + Port Number. If succeeded, “adminip OK” is returned by the device in SMS. e.g, Send SMS command “adminip123456 202.104.150.75 9000” to the 6.35.3.2 tracker device, If succeeded, “adminip OK” is returned by the device in SMS.( 123456 is default password，202.104.150.75 is IP，9000 is port). 6.35.4 Switch to GPRS mode The default mode is “SMS”... -
Page 29: Web Platform And Mobile App Instructions
changed. 6.37 Web platform and mobile APP instructions You must register your account at www.gpstrackerxy.com before using the web service and the mobile APP, The user id and password for web platform and mobile APP is same. 6.37.1 Login www.gpstrackerxy.com, and choose the server to register to. 6.37.2 Filling the user id you like, password and the 15 digits IMEI of the tracker to complete the registration. -
Page 30: Cautions
7 Cautions ： Please comply with the instructions to extend the unit life: Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside circuitry. Don’t use & store the unit in dusty places. Don’t put the unit in overheated or overcooled places. Handle carefully. - Page 31 SMS reply fail Password incorrect or wrong sms commands format Call without SMS reply or cannot receive alarm Authorized number is wrong or without setting any authorized number fail Remove external power , turn on the device and program again Remote Controller Siren’s voltage is DC12V/24V/1A.