Table of Contents
Advertisement
9. Utilities
This section covers the programming of the system utilities.
Time and Date
The system has a real time clock that must be programmed so
that the time and date is recorded correctly in the system event
log. The time and date is also displayed on the bottom line of the
LCD keypad. If the system looses all power, the time and date is
maintained for approximately 2 days.
Locations:
- Hours.
9001
- Minutes.
9002
- Seconds.
9003
- Day.
9004
- Month.
9005
- Year.
9006
Entry Mode:
Number Entry (see page 17).
User Menus
The engineer can access the user menus without exiting the
engineer's program mode by entering
shows the user menu options and the command number used to
access them.
Group
Command
A
/
Arming
S
1
2
3
Reset
R
11
System Tests
12
13
21
Event Log & UDL
22
23
Users
81
91
Menus
99
When using the LCD keypad the menu options and their
command numbers are scrolled on the bottom line of
the LCD. If the
*
is currently being displayed is selected.
Away Arm
Selecting this option will cause the system to start the exit mode
and attempt to away arm the system. To cancel or disarm simply
enter a valid user code.
Stay Arm 1
Selecting this option will cause the system to start the exit mode
and attempt to stay arm (1) the system. To cancel or disarm
simply enter a valid user code.
Stay Arm 2
Selecting this option will cause the system to start the exit mode
and attempt to stay arm (2) the system. To cancel or disarm
simply enter a valid user code.
P0031-LI-01.00
. The table below
91*
Function
Away Arm
Stay Arm 1
Stay Arm 2
Stay Arm 3
Reset alarm or fault
Walk Test
Test Bell & Outputs
Do Test Call
View Log
Print Log
Call UDL
Change code
Program Mode
Exit Menu
key is pressed, the menu option that
Stay Arm 3
Selecting this option will cause the system to start the exit mode
and attempt to stay arm (3) the system. To cancel or disarm
simply enter a valid user code.
Walk Test
Selecting this option allows the detection zones to be tested
without causing an alarm. As each zone is activated, the keypad
generates an acknowledgment tone and the zone number is
added to the list of tested zones. The tested zones are scrolled on
the keypad display. When you have finished testing the zones,
press
to exit this option.
R
Test Bell & Outputs
Selecting this option allows the bell, strobe and any outputs that
have the "User Test" attribute to be switched on and off. After
selecting this command keys 1 to 4 toggle on and off the
following:
Bell Output
1
Strobe Output
2
User Test Outputs
3
Alarm Sounder
4
Press
to exit this option.
R
Do Test Call
Selecting this option will cause the onboard communicator to
send a test call to the alarm receiving centre.
View Event Log
Selecting this option allows the event log to be viewed. The
following keys are used when navigating through the log:
Go backward.
*
Go forward.
#
Press
to exit this option.
R
Print Event Log
Selecting this option causes the contents of the event log to be
sent to the printer. Press
Either Com1 or Com2 must be configured for "Printer"
mode in order to use this feature.
Call UDL
Selecting this option will cause the onboard communicator to call
the remote computer modem, so that a remote link can be
established.
The remote computer must be setup so that it is ready
to receive the call. Only select this option when
instructed to do so by the remote computer operator.
Change Code
Selecting this option allows you to change your own access code.
After selecting this option enter the new access code (4 - 6 digits)
A
followed by
.
*
Program Mode
Selecting this option takes you back to the normal engineer's
program mode.
S
Exit Menu
Selecting this option returns the system to the normal disarmed
state.
2*
to exit this option.
R
3*
11*
12*
13*
21*
22*
23*
81*
91*
99*
37
Advertisement
Table of Contents
