Table Of Contents; Tools Required; Radio/Electrical; Hardware Identification - Team Losi XXX4 Graphite Plus Owner's Manual

Team Losi has supplied all necessary Allen Wrenches and two special assembly wrenches that are needed for slipper adjustment, assembly and
Tierod adjustments. The following common tools will also be required: Needle-nose pliers, regular pliers, medium grit sandpapper, hobby knife,
scissors, and body cutting/trimming tools. A soldering iron may be necessary for electrical installation. 3/16", 1/4", and 11/32" nut drivers are
optional.
A suggested radio layout is provided in this manual. Your high-performance R/C center should be consulted regarding specific questions
pertaining to radio/electrical equipment.
When in question, use the hardware identification guide in each step. For screws, the prefix number designates the screw size and number of
threads per inch (i.e. 4-40 is #4 screw with 40 threads per inch). The second number or fraction, designates the length of the screw. For cap head
and button head screws, this number refers to the length of the threaded portion of the screw. For flat head screws, this number refers to the
overall length of the screw. Bearings and bushings are referenced by the (inside diameter) x (outside diameter) (ie. 3/16 x 3/8). Shafts and pins
are referred to by diameter x length. Washers are described by inside diameter or the screw size that will pass through the inside diameter. E-clips
are sized by the shaft diameter that they attach to.
The XXX-4 G+ includes an 92-tooth, 48-pitch spur gear. The internal drive ratio of the XXX-4 G+ is 2.10. The pinion gear that is used will
determine the final drive ratio. To calculate the final drive ratio, first divide the spur gear size by the pinion gear size. For example, if you are using
a 20-tooth pinion gear, you would divide 92 (spur gear size) by 20 (pinion gear size). 92/20 = 4.60. This tells you that 4.60 is the external drive ratio.
Next, multiply the internal drive ratio (2.10) by the external drive ratio (in this case 4.60). 2.10 x 4.60 = 9.66:1. This means that by using a 20-tooth
pinion gear with the standard 92-tooth spur gear, the final drive ratio is 9.66:1.
Consult you high-performance shop for recommendations to suit your racing style and class. The chart below lists some of the more
common motor types and recommended initial gearing for that motor. Ratios can be adjusted depending on the various track layouts, tire sizes,
and battery types.
TYPE OF MOTOR
10-Turn Modified
11-Turn Modified
12-Turn Modified
13-Turn Modified
14-Turn Modified
15-Turn Modified
1. INTRODUCTION ................................................................................ i
Completed Kit Dimensions .............................................................. i
Notes & Symbols .............................................................................. i
Kit/Manual Organization ................................................................. i
Important Safety Notes .................................................................... i
Tools Required ................................................................................. ii
Radio/Electrical ................................................................................ ii
Hardware Identification .................................................................. ii
Motors and Gearing ........................................................................ ii
2. BAG A ............................................................................................... 1-7
3. BAG B ...............................................................................................8-11
Team Losi is continually changing and improving designs; therefore, the actual part may appear slightly different than the illustrated part. Illustrations of parts and
assemblies may be slightly distorted to enhance pertinent details.

RADIO/ELECTRICAL

HARDWARE IDENTIFICATION

MOTORS AND GEARING

RECOMMENDED INITIAL GEARING FOR COMMON MOTORS
24º (Depending on motor and track size)
8-Turn Modified
9-Turn Modified

TABLE OF CONTENTS

TOOLS REQUIRED

PINION
17-20
16
17
18
19
20
21
22
23
4. BAG C ..........................................................................................12-15
5. BAG D ........................................................................................ 16-20
6. BAG E ......................................................................................... 21-25
7. BAG F ......................................................................................... 26-28
8. BAG G ................................................................................................ 29
9. BAG H ........................................................................................ 30-34
10. Checklist Before Your First Run ................................................ 35
11. Tips From the Team .................................................................. 35-37
12. Spare Parts List ........................................................................ 38-41
ii
SPUR
92
92
92
92
92
92
92
92
92