Menu Configuration - Sony BVM-D9H1j Operation Manual

Menu Configuration

MAIN MENU
M E N U
A
B p C O N T R O L P R E S E T A D J . . .
C O L O R T E M P A D J . . .
C
I N P U T C O N F I G. . .
D
R E M O T E . . .
S Y S T E M C O N F I G . . .
E
S T A T U S . . .
F
A L I G N M E N T . . .
G
A
C O N T R O L P R E S E T A D J
p M A N U A L . . .
A U T O . . .
B
C O L O R T E M P A D J
S T D
M A N U A L
p
P R O B E . . .
C O P Y . . .
C(1/2)
I N P U T C O N F I G ( 1 / 2 )
C H 1
F O R M A T . . . Y P B P R
p
S L O T N O S L O T 1
I N P U T N O
E X T S Y N C S L O T S L O T 1
A U D I O I N P U T
C O L O R T E M P S T D
A P E R T U R E V A L U E 1 0 0
C H A N N E L N A M E. . . P R O G
C(2/2)
I N P U T C O N F I G ( 2 / 2 )
C H 1
1 1 2 5 / 6 0 I S Y S T E M 1 0 8 0 I
p
H P H A S E 0 0 0
M A R K E R P H A S E 0 0 0
M A R K E R W I D T H 0 0 0
N T S C S E T U P 7 . 5
Y P B P R M A T R I X 6 0 I
V C R M O D E O F F
D (next page)
58
(E)
A1
M A N U A L
T O C A N C E L : M E N U
T O C O N F I R M : E N T E R
C H R O M A : 1 00 C O N T R A S T : 1 00
P H A S E : 1 00 B R I G H T
A2
A U T O
F U L L F I E L D W H I T E
p 8 C O L O R B A R 1 0 0 %
8 C O L O R B A R 7 5 %
S M P T E C O L O R B A R
E I A C O L O R B A R
B1(1/2)
A D J U S T
S T D
R E D : C O N T R A S T
G R E E N : B R I G H T
B L U E : C H R O M A
L U M I N A N C E : P H A S E
T O C A N C E L : M E N U
T O C O N F I R M : E N T E R
G A I N
: 0 5 0 0 G : 0 5 0 0 R : 0 5 0 0
B
B2
P R O B E
S T D
p S T A R T
P R O B E B K M - 1 4 L
X
Y
L O W L I G H T ( 2 0 I R E )
H I G H L I G H T ( 1 0 0 I R E )
L O A D R E F V A L U E . . .
B3
C O P Y F R O M
S T D
S T D
p C O L 1
C O L 2
D 6 5
D 9 3
Set input signal data for each channel.
↓
:Current channel is indicated.
:Select the input signal type.
:Select the slot number.
1
:Select the input connector number.
1
:Select the slot when the external sync signal is used.
:Select the audio input number (BVM-D9H5 only)
:Select the color temperature.
:Enter the aperture adjustment value.
:Give the channel name. (Select in the "C2" menu)
↓ :Current channel is indicated.
:Select the number of active scanning lines per frame.
:Set the holizontal picture position.
:Set the 4:3 marker position.
:Set the 4:3 marker width.
:Set the NTSC setup level when the BKM-127W is installed.
:Select the matrix when YP P
B
480/60I or 480/60P are input.
:Select ON to compensate for a distorted picture when the input
signals from the VCR are not typical. (Effective only when the
signal formats 480/60I or 575/50I are input.)
Set the preset value with the
adjustment knobs.
K E Y
K E Y
: 1 00
Set by automatic adjustment (using the
color bar signal)
1 0 0 %
B1(2/2)
↓
A D J U S T
S T D
K N O B
K N O B
K N O B
K N O B
K E Y
K E Y
B I A S
: 0 5 0 0 G : 0 5 0 0 R : 0 5 0 0
B
Select the probe for color temperature adjustment.
:Select the probe (BKM-14L, SLS 9400, CA-100, TF6,
or PM 5639)
0 . 3 1 3
:Confirm/Change x, y value on the Chromaticity
0 . 3 2 9
Coordinate and luminance
2 . 7
1 2 0
You can copy the color temperature
data.
C1
C H
Y P B P R
p
R G B
N T S C , P A L
D 1 - S D I
H D - S D I
C2
C H
P R O G
p
E D I T
C A M
V T R
N E W
signals of the signal formats
R
↓
B21
R E F V A L U E
p D 6 5
D 9 3
F O R M A T
1
:Select the level of
S M P T E
YP P
B R
C H A N N E L N A M E
1
N A M E
signals.