Appendix; Emergency Code Table - Sony DVP-K800D Service Manual

5-8. Appendix

5-8-1. Emergency Code Table

Automatic Adjustment, Manual Control $
SA.FFFFFF SI.00 EMG.00
History of emergencies $
No. EMG MECHA DISC MODE ERR2 ERR3
00: NO EMG
02: EEPROM writing: NG (Check Sum has abnormality)
01: EEPROM reading: NG (Check Sum has abnormality)
03: EEPROM BUSY is displayed continuously exceeding the
specified time.
04: The pointer that shows the newest Emg History has abnormality.
06: Communication between the HI microprocessor and the SYS
microprocessor is interrupted for a specified time.
07: HI microprocessor cannot detect V-sync.
—— 1x : Electrical adjustment ——
10: EEPROM CHECK NG
16: DSP CHECK NG
—— 2x : Mechanism ———
20: Time out of home position movement
21: Sled driver has abnormal voltage.
—— 3x : Tilt/Adjustment ——
30: Hy Det Level adjustment has abnormality.
31: Sled Offset Cancel adjustment has abnormality.
32: Focus Gain adjustment is faulty.
33: Tracking Offset adjustment is faulty.
34: Tracking Gain adjustment is faulty.
35: JITTER NG (only during the automatic adjustment)
—— 4x : Focus ———
40: Focus Servo does not lock in.
41: Focus Jump failed.
—— 5x : Tracking ——
—— 6x : Spindle ——
60: Mis-chucking when disc is inserted.
61: When disc started rotation, it did not reach the target speed
within 3 seconds.
62: Spindle runs away/does not stop.
63: Lock Check (in the service mode only)
64: CLV servo does not lock in within the specified time.
65: FG servo does not reach the target speed within the specified
time.
66: Spindle is not rotating at x1 speed.
—— 7x : Seek system ——
70: System control requests address that does not exist.
71: System control requests time code that is not exist.
72: System control requests track No. that is not exist.
73: Seek operation is not completed within the specified number
of times.
—— 8x : Data related items ——
80: Continuity of address has abnormality. (DVD)
81: Cannot read address even retry is executed. (CD)
82: TOC read is not completed within the specified period of time.
83: Physical Information Read Error ( CTRL DATA ECC ERR)
84: Physical Information Read Error ( CTRL DATA INSA ERR)
85: Physical Information Read Error ( CTRL DATA FULL ERR)
86: Physical Information Read Error ( CTRL DATA RUN OVER)
87: Physical Information Read Error ( CTRL DATA Time Out)
88: Layer No has abnormality.
89: CD Text Data Read Error
—— 9x : etc ———
90: Servo recovery has failed when starting a disc.
96: Servo Auto Sequence Time Out
97: Servo Auto Sequence has exceeded the specified times.
The data of 0xA0 and higher is not displayed, but is stored in the
error history.
For system control debugging (during stop mode)
A0: Stop request from drive microprocessor
A1: Did not return to the mode for a specified time.
A2: Feed error. Retry is impossible.
A3: GetInfo error. Stop
A4: An attempt is made to playback a DVD-R Disc
A5: Failed to execute Decrypt
A6: SlowR. Target address of searching is illegal.
A7: Feed error. Stop
For system control debugging (during retry mode)
B0: Due to feeder.
B1: Due to video hang-up
B2: Error in DMX
B3: Waiting for data from SlowR
B4: Navi Pack sector address is different during SlowR mode
B5: Video hang-up during SlowR mode
B6: Time out while waiting for ending of SlowR Gttgt
B7: Waiting for data during FF/FR
B8: Waiting for video data during FF/FR
5-29