Appendix; Emergency Code Table - Sony DVP-M35 Service Manual

5-8. Appendix

5-8-1. Emergency Code Table

Automatic Adjustment, Manual Control $
SA.FFFFFF SI.00 EMG.00
History of emergencies $
No. EMG MECHA DISC MODE ERR2 ERR3
00: NO EMG
01: EEPROM reading: NG (Check Sum has abnormality)
02: EEPROM writing: NG (Check Sum has abnormality)
03: EEPROM BUSY is displayed continuously exceeding the
specified time.
04: The pointer that shows the newest Emg History has abnormality.
06: Communication between the HI microprocessor and the SYS
microprocessor is interrupted for a specified time.
07: HI microprocessor cannot detect V-sync.
—— 1x : Electrical adjustment ——
10: EEPROM CHECK NG
16: DSP CHECK NG
—— 2x : Mechanism ———
20: Time out of home position movement
21: Sled driver has abnormal voltage.
26: (Changer) TRAY NG
27: (Changer) ROULETTE NG
—— 3x : Tilt/Adjustment ——
30: Hy Det Level adjustment has abnormality.
31: Sled Offset Cancel adjustment has abnormality.
32: Focus Gain adjustment is faulty.
33: Tracking Offset adjustment is faulty.
34: Tracking Gain adjustment is faulty.
35: JITTER NG
—— 4x : Focus ———
40: Focus Servo does not lock in.
41: Focus Jump failed.
42: DSP Error Code (not used)
—— 5x : Tracking ——
—— 6x : Spindle ——
60: Mis-chucking when disc is inserted.
61: When disc started rotation, it did not reach the target speed
within 3 seconds.
62: Spindle runs away/does not stop.
63: LVLOCK NG
64: CLV servo does not lock in within the specified time.
65: FG servo does not reach the target speed within the specified
time.
66: Spindle is not rotating at x1 speed. (RF Edge)
—— 7x : Seek system ——
70: System control requests address that does not exist.
71: System control requests time code that is not used.
72: System control requests track No. that is not used.
73: The lock-in operation is not completed within the specified
number of times.
—— 8x : Data related items ——
80: Continuity of address has abnormality. (DVD)
81: Cannot read address even retry is executed. (CD)
82: TOC read is not completed within the specified period of time.
83: Physical Information Read Error ( CTRL DATA ECC ERR)
84: Physical Information Read Error ( CTRL DATA INSA ERR)
85: Physical Information Read Error ( CTRL DATA FULL ERR)
86: Physical Information Read Error ( CTRL DATA RUN OVER)
87: Physical Information Read Error ( CTRL DATA Time Out)
88: Layer No has abnormality.
89: CD Text Data Read Error
—— 9x : etc ———
90: Servo recovery has failed when starting a disc.
96: Auto Sequence Time Out
97: Auto Sequence has exceeded the specified times.
98: Not used
99: Not used
The data of 0xA0 and higher is not displayed, but is stored in the
error history.
For system control debugging (during stop mode)
A0: Stop request from drive microprocessor
A1: Did not return to the mode for a specified time.
A2: Feed error. Retry is impossible.
A3: GetInfo error. Stop
A4: An attempt is made to playback a DVD-R Disc
A5: Failed to execute Decrypt
A6: SlowR. Target address of searching is illegal.
A7: Feed error. Stop
For system control debugging (during retry mode)
B0: Due to feeder.
B1: Due to video hang-up
B2: Error in DMX
B3: Waiting for data from SlowR
B4: Navi Pack sector address is different during SlowR mode
B5: Video hang-up during SlowR mode
B6: Time out while waiting for ending of SlowR Gttgt
B7: Waiting for data during FF/FR
B8: Waiting for video data during FF/FR
5-29