Extron electronics FOXBOX Tx HDMI User Manual page 31

Command/response table for Receiver SIS commands (continued)
Command ASCII Command
(host to unit)
Video shutdown delay
NOTES: • The Set Video Delay command delays the digital video to help monitors sync correctly during an input rate change.
• Only video is delayed; embedded audio is not delayed.
Set delay 3*
Example: 3*3#
View delay 3#
Switch and signal status requests
E
Request Audio switch status
NOTE:
The audio on the captive screw audio output always remains active regardless of the setting of this switch.
E
Check audio embed
View link 1 (Tx-to-Rx) status 1S
2S
View link 2 (Rx-to-Tx) status
3S
View input video status
View input audio status 4S
View all signal status 5S
6S
View HDMI signal status
View HDCP status 7S
View temperature 20S
Information requests
Information request I
Show firmware version Q
Example: Q
N
Request part number
Resets
E
Reset memory presets
E
System reset
NOTE: X(
= Mute and auto memory status
X1%
= Switch position
X1! = Link status
X2!
= Video delay
(0 plus six steps at 0.25 seconds per step)
X1$
= Firmware version
X1@
= Internal temperature
Response
(unit to host)
X2! X2!]
# Dly
]
Dly3
X2!]
} X1%]
Stat
}
5Stat EmbedAud
X1!]
X1!]
X1!]
X1!]
X1!
SigI
X1!
SigI
X1!
HdcpI
X1@ X1@
F •
X1!
1Lnk
X1$]
]
1.23
60-1174-nn
} ]
ZG Zpg
} ]
ZXXX Zpx
0 = off
0 = off (right)
0 = light or signal input not detected
1 = light or signal detected
0 = 0 second
1 = 0.25 second
2 = 0.5 second (default)
v.vv
nnnF•nnC
Additional description
Delay video by an interval of
Delay video by an interval of 0.75 seconds
(3 x 0.25 seconds).
Show the position of the Audio switch:
0 = off (embedded audio is muted) or 1 = on (unmute).
X1!]
Show if audio is embedded in the video stream:
0 = not detected or 1 = detected.
X1! X1! X1!]
• SigO • HdcpI • HdcpO
Report the status of the HDMI input, HDMI output
(always -- for a transmitter), HDCP encoding on the
input, and HDCP encoding on the output.
X1!]
• SigO Report the status of the HDMI input and HDMI
output (always -- for a transmitter).
X1!]
Report the status of the HDCP encoding on the
• HdcpO
input and HDCP encoding on the output.
]
C Show temperature in degrees Fahrenheit and Celsius.
X1! X1! X1! X1#
•2Lnk •Vid •Aud • •Rx
The unit responds with the current status (signal
detected) of optical link 1, optical link 2, the
video input, and the audio link; the fiber optic
transmission mode (singlemode or multimode); and
the device type (Rx).
The factory-installed firmware version is 1.23
(sample value only).
]
Numbers" in the "Reference
See "Part
Information" section.
Reset (erase) all memory presets.
Reset all settings to factory defaults.
1 = on
1 = on (left)
3 = 0.75 second
4 = 1.0 second
FOXBOX Tx/Rx HDMI • Remote Control
X2!
.
]
5 = 1.25 second
6 = 1.5 second
25