Extron electronics FOXBOX Tx HDMI User Manual page 27

Command/response table for Transmitter SIS commands (continued)
Command ASCII Command
(host to unit)
Audio input gain and attenuation
NOTES: • The set gain (G) and set attenuation (g) commands are case sensitive. The increment level, decrement level, and show level are
not case sensitive.
• When the controlling PC is connected to the receiver, the PowerCage FOX can perform this command only if the receiver-Tx-to-
transmitter-Rx fiber cable is connected. The unit returns the E14 error if the Rx fiber is not connected.
X^
Set input audio gain to a
+dB value
Example: 2G
X*
Set input audio attenuation
to a -dB value
Increment input level +G
Example: +G
–G
Decrement input level
G
Show input level
Plus mode transmission
NOTE:
Plus mode forces the transmitter to emulate a FOXBOX DVI Plus or PowerCage FOX DVI Plus transmitter) .
81*1#
Enable Plus mode
Disable Plus mode 81*0#
View Plus mode 81#
Input reports as an HDCP authorized device
E
HDCP authorized device on
E
HDCP authorized device off
E
View HDCP authorized
device status
Status requests
View link 1 (Tx-to-Rx) status 1S
View link 2 (Rx-to-Tx) status 2S
3S
View input video status
View input audio status 4S
View all signal status 5S
6S
View HDMI signal status
View HDCP status 7S
View temperature 20S
NOTE: X^
= Audio gain adjustment range
X&
= Audio level adjustment range
X*
= Audio attenuation adjustment range
X( = Enable or disable status
X1) = HDCP authorized device
X1!
= Link and input status
X1@
= Internal temperature
Response
(unit to host)
X&]
G Aud
Aud+02.0
X&]
g Au d
X&]
Aud
Aud+03.0
Aud–01.0
X&]
]
Plus1
]
Plus0
X(]
}
E1HDCP HdcpE1
}
E0HDCP HdcpE0
} X1)]
EHDCP
X1!]
X1!]
X1!]
X1!]
X1!
SigI
X1!
SigI
X1!
HdcpI
X1@ X1@
F •
00 to 10
-18 to +10 (in 1.0 dB steps)
00 to 18
0 = off (down) or disable
0 = off
0 = link or input not detected 1 = link or input detected
nnnF•nnC
Additional description
Set the input level to
]
Set the input level to +2 dB (gain).
Set the input level to
Increase the audio level by 1 dB.
]
Increment the input level from +2 dB to +3 dB.
]
Decrease the audio level from 0 dB to –1 dB.
Turn on Plus mode (default).
Turn off Plus mode.
Show Plus mode status.
]
Set the transmitter as an HDCP authorized device.
]
Set the transmitter as not an HDCP authorized device.
Show HDCP authorized device status.
X1! X1! X1!]
• • •
SigO HdcpI HdcpO
Report the status of the HDMI input, HDMI output,
HDCP encoding on the input, and HDCP encoding
on the output.
X1!]
• SigO Report the status of the HDMI input and HDMI
output (always -- for a transmitter).
X1!]
Report the status of the HDCP encoding on the
• HdcpO
input and HDCP encoding on the output.
]
Show temperature in degrees Fahrenheit and Celsius.
C
1 = on (up) or enable
1 = on
FOXBOX Tx/Rx HDMI • Remote Control
X&
dB (gain).
X&
dB (attenuation).
21