Instructions For Rcsitea (Sddvtcs Series) - Vermont Castings SDDVTCSBDSB Installation And Operating Instructions Manual

Instructions for RCSITEA
SDDVTCS Series
CAUTION: The RCSITEA is only certified for use on vent-
ed heater rated equipment.
This remote control system provides a safe, reliable and
user-friendly remote control for millivolt valve gas appli-
ances, blower speed and flame height adjustment. The
system can be manually or thermostatically turned on and
off with the transmitter.
Carefully inspect the contents for shipping damage. If any
parts are missing or damaged, immediately contact your
dealer. Do not attempt to install any part of the kit unless
all parts are in good condition. Refer to instructions pro-
vided with the kit for complete installation instructions.
WARNING: Make sure 120V AC fan and SIT valve are
correct. If not wired correctly, damage to receiver could
result. Make sure the wires do not contact the appliances
any place other than at the terminals. Exposure to tem-
peratures higher than 250°F (105°C) may cause the re-
ceiver to malfunction and cause possible fire hazard.
Remote Transmitter
Install Batteries
The remote transmitter uses three (3) "AAA" batteries.
1. Press down the battery door tab
and pull out to remove the battery
door. (Figure 58)
2. Install the batteries as indicated
on transmitter.
3. Close the battery door by snap-
ping in place.
4. When three (3) batteries are in-
stalled, the transmitter will initial-
ize for 10 seconds and then is
ready for use.
5. The batteries should be replaced
at least once every six (6) months
or when the low battery indicator
is displayed.
Setting Privacy (DIP) Switch on Receiver and Trans-
mitter
The remote receiver and transmitter privacy (DIP) switch-
es are preset at the factory. In the event of activation or
interference from other nearby transmissions, reset the
code using the following procedure:
1. Slide the code switches on the transmitter and receiver
to choice of ON or OFF position. Switches #1, #2, #3
and #4 are preset to "ON" for both the transmitter and
receiver. (Figure 59)
2. The switches on the transmitter and receiver must
20306760
Stardance® Direct Vent/Natural Vent Gas Heater
3. To check, press either the ON or OFF button on the
4. The system is now ready to operate.
dip switch settings, they will communicate with each oth-
er. This may cause the appliances to malfunction.
Figure 59 The switches on the transmitter and
Reset Button
The reset button can be used to reset the transmitter if
Battery
transmitter is not working properly. The reset button is lo-
Door
Tab
cated behind the battery door cover in the lower left cor-
ner of battery compartment. Using a paper clip, press the
reset button and the transmitter will reset and initialize for
10 seconds before it can be used.
Transmitter
General
The RCSITEA Remote Control has two (2) operating
Figure 58
modes: Manual and Thermostatic.
Battery door tab.
The control system can be set to
temperature ranges between 45°F
ST1088
and 90°F. The blower speed and
RCSITE battery tab
flame height can be adjusted in
either the manual or thermostatic
mode.
The transmitter will operate the re-
mote receiver from 1 foot to a max-
imum of 30 feet. The distance is
reduce when batteries are low or
when the receiver is inside a metal
enclosure.
match in order for the system to work.
transmitter and the receiver indicator light will blink. If
not, repeat Step 2.
NOTE: Refer to optional 6 Hour Shutdown.
WARNING: Do not use two (2) or more remote
control systems in the same area with the same
Dip Switch
(Default)
ON DIP
Transmitter
receiver must match.
ST1089
RCSITE dip switches
Operation
ON DIP
Receiver
ST1089
ON
AUTO
FAN
FLAME
OFF
AMBIENT
Figure 60
RCSITEA remote
transmitter.
ST1090
33
RCSITE remote