Instructions For Rcsitea (Sddvtcs Series) - Vermont Castings SDDVTCB Homeowner's Installation And Operating Manual

Instructions for RCSITEA
SDDVTCS Series
CAUTION: The RCSITEA is only certified for use on vent-
ed heater rated equipment.
This remote control system provides a safe, reliable and
user-friendly remote control for millivolt valve gas appli-
ances, blower speed and flame height adjustment. The
system can be manually or thermostatically turned on and
off with the transmitter.
Carefully inspect the contents for shipping damage. If any
parts are missing or damaged, immediately contact your
dealer. Do not attempt to install any part of the kit unless
all parts are in good condition. Refer to instructions pro-
vided with the kit for complete installation instructions.
WARNING: Make sure 120V AC fan and SIT valve are
correct. If not wired correctly, damage to receiver could
result. Make sure the wires do not contact the appliances
any place other than at the terminals. Exposure to tem-
peratures higher than 250°F (105°C) may cause the re-
ceiver to malfunction and cause possible fire hazard.
Remote Transmitter
Install Batteries
The remote transmitter uses three (3) "AAA" batteries.
1. Press down the battery door tab
and pull out to remove the battery
door. (Fig. 57)
2. Install the batteries as indicated
on transmitter.
3. Close the battery door by snap-
ping in place.
4. When three (3) batteries are in-
stalled, the transmitter will initial-
ize for 10 seconds and then is
ready for use.
5. The batteries should be replaced
at least once every six (6) months
or when the low battery indicator is displayed.
Setting Privacy (DIP) Switch on Receiver and Trans-
mitter
The remote receiver and transmitter privacy (DIP) switch-
es are preset at the factory. In the event of activation or
interference from other nearby transmissions, reset the
code using the following procedure:
1. Slide the code switches on the transmitter and receiver
to choice of ON or OFF position. Switches #1, #2, #3
and #4 are preset to "ON" for both the transmitter and
receiver. (Fig. 58)
2. The switches on the transmitter and receiver must
match in order for the system to work.
30004968
3. To check, press either the ON or OFF button on the
4. The system is now ready to operate.
NOTE: Refer to optional 6 Hour Shutdown.
malfunction.
Reset Button
The reset button can be used to reset the transmitter if
Battery
transmitter is not working properly. The reset button is lo-
Door
Tab
cated behind the battery door cover in the lower left cor-
ner of battery compartment. Using a paper clip, press the
reset button and the transmitter will reset and initialize for
10 seconds before it can be used.
Transmitter
General
The RCSITEA Remote Control has two (2) operating
Fig. 57 Bat-
modes: Manual and Thermostatic.
tery door tab.
The control system can be set to
ST1088
temperature ranges between 45°F
RCSITE battery tab
and 90°F. The blower speed and
flame height can be adjusted in
either the manual or thermostatic
mode.
The transmitter will operate the
remote receiver from 1 foot to a
maximum of 30 feet. The distance
is reduce when batteries are low or
when the receiver is inside a metal
enclosure.
Stardance® Direct Vent/Natural Vent Gas Heater
transmitter and the receiver indicator light will blink. If
not, repeat Step 2.
WARNING: Do not use two (2) or more remote
control systems in the same area with the same
dip switch settings, they will communicate with
each other. This may cause the appliances to
Dip Switch
(Default)
ON DIP
Transmitter
Fig. 58 The switches on the transmitter and receiver must
match.
ST1089
RCSITE dip switches
Operation
ON DIP
Receiver
ST1089
ON
AUTO
FAN
FLAME
OFF
AMBIENT
Fig. 59 RCSITEA
remote transmitter.
ST1090
33
RCSITE remote