NetComm NWL-15 User Manual page 96

List of get/set commands
The following table is a partial list of get and set commands which may be performed via SMS.
COMMAND
NAME
get status get status
get sessionhistory get sessionhistory
set
set syslogserver
syslogserver=123.45.67.89:514
set cod set cod=1
get cod get cod
get codstatus get codstatus
set coddialport set coddialport=on,53
get coddialport get coddialport
set codonline set codonline=20
get codonline get codonline
set codminonline set codminonline=10
get codminonline get codminonline
set codredial set codredial=5
get codredial get codredial
set coddisconnect set coddisconnect=0
get coddisconnect get coddisconnect
set codconnectreg set codconnectreg=30
get codconnectreg get codconnectreg
set codrandomtime set codrandomtime=3
get codrandomtime get codrandomtime
set codverbose set codverbose=1
get codverbose get codverbose
set codignore.icmp set codignore.icmp=1
get codignore.icmp get codignore.icmp
set codignore.tcp set codignore.tcp=1
get codignore.tcp get codignore.tcp
set codignore.udp set codignore.udp=1
get codignore.udp get codignore.udp
set codignore.dns set codignore.dns=1
get codignore.dns get codignore.dns
set codignore.ntp set codignore.ntp=1
get codignore.ntp get codignore.ntp
set codignore.ncsi set codignore.ncsi=1
get codignore.ncsi get codignore.ncsi
get pppoe get pppoe
set pppoe set pppoe=1, telstra.internet, test
get ledmode get ledmode
set ledmode set ledmode=10
get ssh.proto get ssh.proto
set ssh.proto set ssh.proto=1,2
NetComm Wireless Light Industrial M2M Router Plus
96
EXAMPLE
Returns the Module firmware version, LAN IP Address, Network State, Network operator and
RSSI.
Returns the time and date of recent sessions along with the total amount of data sent and
received for each session.
Sets a remote syslog server IP or hostname and port.
Enables or disables Connect on demand.
Returns the enable/disable status of the Connect on demand feature.
Returns the connection status of the Connect on demand feature.
Sets the Connect on demand feature to connect only when traffic is received on the specified
port.
Returns the Connect on demand port filter status and list or filtered ports.
Sets the router to stay online for at least X minutes when data activity is detected.
Returns the number of minutes the router is configured to stay online when data activity is
detected.
Sets the router to stay online for a minimum of X minutes after connecting.
Returns the minimum number of minutes the router should stay online after connecting.
Sets the number of minutes that the router should not attempt to redial after hanging up.
Returns the number of minutes that the router is configured to not attempt to redial after
hanging up.
Sets the number of minutes after which the router should disconnect regardless of traffic.
Returns the number of minutes the router is configured to disconnect regardless of traffic.
Sets the number of minutes that the router should regularly attempt to connect.
Returns the number of minutes that the router is configured to regularly attempt to connect.
Sets the number of minutes that the router should randomise the dial time by.
Returns the number of minutes that the router is configured to randomise the dial time by.
Sets verbose logging on or off.
Returns the status of verbose logging.
Sets the router to ignore ICMP packets triggering data activity detection.
Returns the status of the Ignore ICMP option.
Sets the router to ignore TCP packets triggering data activity detection.
Returns the status of the Ignore TCP option.
Sets the router to ignore UDP packets triggering data activity detection.
Returns the status of the Ignore UDP option.
Sets the router to ignore DNS traffic triggering data activity detection.
Returns the status of the Ignore DNS option.
Sets the router to ignore NTP traffic triggering data activity detection.
Returns the status of the Ignore NTP option.
Sets the router to ignore NCSI traffic triggering data activity detection.
Returns the status of the Ignore NCSI option.
Returns the PPPoE status, currently configured dial string and service name
Sets the PPPoE status on, APN to telstra.internet, and service name to test.
Returns the status of the LED operation mode.
Sets the LED operation mode to be always on or to turn off after the specified number of
minutes.
Returns the SSH protocol in use.
Sets the SSH Protocol to protocol 1, 2 or both (1,2).
DESCRIPTION
www.netcommwireless.com