Assigning Functions To Assign Switches; Selecting The Lens File - Sony PDW-F335L Operating Instructions Manual

Description
Item
1 Reduce noise by using the noise reduction
circuits, without lowering the sensitivity.
Resolution and gradations under low light are
slightly lower.
2 Reduce noise more than the 1 setting by
lowering the sensitivity. Compared to the OFF
setting, sensitivity is about 20% lower, and the
dynamic range is about 20% lower. (Sensitivity
declines to about F8, compared to the standard
F9.)
Assigning Functions to ASSIGN
Switches
You can assign the desired function to any of the ASSIGN
switches.
(How to select an item in the menu screen: Turn the
MENU knob to move the b mark to the desired item.)
1
Display the ASSIGNABLE page on the OPERATION
menu, and press the MENU knob.
For details on menu operations, see "Basic Menu
Operations" on page 132.
You can assign functions by using the following items.
Item Description
ASSIGN SW <1> Assigns the function to ASSIGN 1
switch.
ASSIGN SW <2> Assigns the function to ASSIGN 2
switch.
ASSIGN SW <3> Assigns the function to ASSIGN 3
switch.
ASSIGN SW <4> Assigns the function to ASSIGN 4
switch.
2
Select the desired ASSIGN switch (ASSIGN SW <1>
to <4>), and press the MENU knob.
The corresponding ASSIGN SW (1 to 4) SEL window
appears. You can assign one of the following functions
to the ASSIGN switch.
Function Description
OFF Assign no function.
MARKER Turn the display of all markers on
or off.
RETAKE Delete the last recorded clip. (This
function is disabled when the Clip
Continuous Rec function is on.)
ATW Turn ATW on or off.
LENS RET Use the recording review function.
REC SWITCH Start/stop recording.
a)
Function Description
TURBO SWITCH Use the gain value set for GAIN
TURBO (see page 142).
ZOOM TELE/ Sets ASSIGN SW<3> to lens
WIDE zoom TELE, and ASSIGN SW<4>
to lens zoom WIDE. (ASSIGN
SW<1> and ASSIGN SW<2>
cannot be assigned to zoom.)
ZOOM WIDE/ Sets ASSIGN SW<3> to lens
TELE zoom WIDE, and ASSIGN
SW<4> to lens zoom TELE.
(ASSIGN SW<1> and ASSIGN
SW<2> cannot be assigned to
zoom.)
FREEZE MIX Output the freeze image and
camera input alternately, to allow
frame alignment (automatic
switching).
SHOT MARK1 Use the shot mark 1 function.
SHOT MARK2 Use the shot mark 2 function.
b) Turn EZ mode on or off.
EZ MODE
b) Turn the EZ focus function on or
EZ FOCUS
off.
SKIN DETAIL ON/ Turn the skin detail adjustment
function on or off.
b)
OFF
b)
SPOT LIGHT Use auto iris spotlight mode
b)
BACK LIGHT Use auto iris backlight mode
b), c) Enter or exit TLCS mode.
TLCS
PICTURE CACHE Turn the Picture Cache function
on or off.
AWB Execute the auto white balance
function.
SHUTTER SW Turn the shutter on or off.
SHUTTER MODE Execute shutter mode switching
and shutter speed switching.
CLIP CONT REC Turn the Clip Continuous Rec
function on or off.
a) Even when the MARKER item is set to OFF on the MARKER page
of the OPERATION menu, the ASSIGN switches allow you to turn
the display of all markers on or off.
b) Function assignable to ASSIGN 1 and ASSIGN 2 switches only
c) Abbreviation for Total Level Control System. A function to operate
the automatic gain control (AGC) and electronic shutter (AE) to
adapt to varying lighting conditions while shooting.
d) Use when shooting a subject at which a spotlight is directed.
e) Use when shooting a backlit subject.
3
Select the desired function, and press the MENU knob.
The function is assigned, and the ASSIGNABLE page
appears again.

Selecting the Lens File

You can change the lens file according to the lens in use.
Adjustments and Settings from Menus
d)
e)
145