Sub-Zero Integrated Refrigeration Installation Manual
  1. Manuals
  2. Brands
  3. Sub-Zero Manuals
  4. Refrigerator
  5. INTEGRATED REFRIGERATION
  6. Installation manual
Sub-Zero Integrated Refrigeration Installation Manual

Sub-Zero Integrated Refrigeration Installation Manual

Integrated refrigeration
Hide thumbs Also See for Integrated Refrigeration:
Table of Contents

Advertisement

Quick Links

See also: Use and Care Manual
INSTALLATION GUIDE

Integrated Refrigeration

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Integrated Refrigeration and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sub-Zero Integrated Refrigeration

Summary of Contents for Sub-Zero Integrated Refrigeration

  • Page 1: Integrated Refrigeration

    INSTALLATION GUIDE Integrated Refrigeration...

  • Page 2: Table Of Contents

    Contents Important Note Integrated Refrigeration ..... . . 3 To ensure the safe and efficient installation of Sub-Zero equipment, please take note of the following types of Model Specifications .

  • Page 3: Integrated Refrigeration

    Any questions or problems regarding the installation as they will be exposed when the doors are open. should be directed to your Sub-Zero dealer or Sub-Zero customer service at 800-222-7820. You may also check the contact & support section of our website, subzero.com.

  • Page 4: Model Specifications

    Model Specifications Overall Dimensions 27" MODELS (686) 27" 24" (686) (610) 14" (356) " (21) " (1995) 80" (2032) TO TOP OF 27" 24" " " (686) (610) OPENNG (10) (10) " " " " (337) (337) (13) (13) " (876) "...

  • Page 5: Overall Dimensions

    Model Specifications subzero.com Overall Dimensions 36" MODELS (914) 36" 24" (914) (610) 14" (356) " (33) " (1976) 80" (2032) TO TOP OF " OPENNG (10) " " (337) (13) " " (876) (260) " (518) " (248) 4" HEIGHT DIMENSIONS ± 1 "...

  • Page 6: Site Preparation

    Site Preparation Opening Dimensions INTEGRATED MODELS TOP VIEW 25" (635) OPENING DEPTH 25" (635) OPENING DEPTH OPENING OPENING WIDTH HEIGHT SIDE VIEW FRONT VIEW IMPORTANT NOTE: The depth of each integrated model is Opening Width 24" (610) from the front of the unit to its back. Your design may 700TR, 700TF(I) and 700TC(I) 27"...

  • Page 7: Electrical Requirements

    Site Preparation subzero.com Electrical Requirements The electrical supply should be located within the shaded area shown in the illustrations. Follow the National The outlet must be checked by a qualified electrician Electrical Code and local codes and ordinances when to be sure that it is wired with the correct polarity. installing the receptacle.

  • Page 8: Plumbing Requirements

    FLOOR " A saddle valve kit (4200880) is available from your (19) TOP VIEW FRONT VIEW Sub-Zero dealer. An in-line filter is required when water conditions have 36" models. (914) a high sediment content. A reverse osmosis system can be used provided there is Plumbing Requirements constant water pressure of 20 psi (1.4 bar) to 100 psi...
  • Page 9 Site Preparation subzero.com Anti-Tip Bracket Installation WOOD FLOOR APPLICATIONS Use the six #12 x 2 " wood screws and the six " flat To prevent the unit from tipping forward and provide washers provided. Drill pilot holes " (5) diameter a stable installation, the unit must be secured in place with the anti-tip brackets shipped with the unit.
  • Page 10 Site Preparation Anti-Tip Bracket Installation Unpacking and Moving Uncrate the unit and inspect for any damages. Remove INSTALL CONCRETE WEDGE ANCHORS: the wood base and discard the shipping bolts that hold the 1) Drill a " (10) diameter hole any depth exceeding the wood base to the bottom of the unit.

  • Page 11: Integrated Installation

    Slide the unit into position, making sure the anti-tip If two integrated units are installed closer than 2" (51) to bracket is engaged properly. Extend the front leveling legs one another, it is necessary to use the Sub-Zero dual down approximately " (5) to make additional adjust- installation heater kit (7007529).
  • Page 12 Integrated Installation Level the Unit Molding Installation Level the integrated unit by turning the front leveling legs The decorative white molding strips for the side and top of clockwise to raise the unit, or counterclockwise to lower it. the unit can be snapped into place. The top molding strip To assist you in adjusting the front leveling legs up or used on integrated tall units, must be installed before the down, use a standard screwdriver blade and place it in the...
  • Page 13 Integrated Installation subzero.com Water Line Connection QUICK CONNECT WATER VALVE For units with an ice maker, the quick connect water valve Shut power off at the circuit breaker before making and PEX tubing are located on the bottom right side of the electrical connection to the solenoid.
  • Page 14 Integrated Installation Kickplate/Grille Installation Once the integrated unit is secured, the kickplate/grille The kickplate/grille may be painted another color, if can be installed. The mounting bracket may be adjusted desired. Follow these easy steps: slightly forward or back so the kickplate/grille will fit flush •...
  • Page 15 Stainless steel panels are available as sales accessories the front of the door and set aside. Place the door panel through your Sub-Zero dealer. To obtain local dealer infor- lying face down on a protected surface to ensure that the mation, visit the showroom locator section of our website, front is not scratched or damaged.

  • Page 16: Panel Installation

    Integrated Installation Panel Installation DOOR PANEL INSTALLATION PANEL BRACKET POSITIONING Before attaching the door panel to the door, place two The illustration below shows mounting hardware location screws in the center of each mounting position, just for door and drawer panels. Dimensions are based on a enough that the slotted holes on the hinge side door panel "...
  • Page 17 Integrated Installation subzero.com Panel Installation With the two mounting brackets in place, install the DRAWER PANEL INSTALLATION drawer panel by engaging the top tabbed bracket first, Remove the mounting hardware provided and set aside. then slide the lower ’L’ bracket onto the positioning As with the door panel, you should work on the back side screws.
  • Page 18 When two integrated units are installed closer than 2" (51) To ensure a safe and proper installation, the following to one another, it is necessary to use the Sub-Zero dual checklist should be completed by the installer to ensure installation heater kit (7007529 or 7007530). The heater that no part of the installation has been overlooked.

  • Page 19: Service Information

    The information and images in this guide are the copyright property of Sub-Zero, Inc. Neither this guide nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero, Inc. ©Sub-Zero, Inc. all rights reserved .
  • Page 20 SUB-ZERO, INC. P. O. BOX 44130 MADISON, WI 53744 SUBZERO.COM 800.222.7820 7012802 REV-A 6/ 2009...

This manual is also suitable for:

700tr700tf(i)700tc(i)700br700bf(i)700bc(i)

Table of Contents