Download  Print this page

GE NetworX NX-6 Installation And Startup

Networx series
Hide thumbs

Advertisement

NetworX Series
NX-6 CONTROL PANEL
Installation and Startup

Advertisement

Table of Contents
loading

  Also See for GE NetworX NX-6

  Related Manuals for GE NetworX NX-6

  Summary of Contents for GE NetworX NX-6

  • Page 1 ™ NetworX Series NX-6 CONTROL PANEL Installation and Startup...
  • Page 2 GE Security. This document contains proprietary information of GE Security and is furnished to its customer solely to assist that customer in the installation, testing, operations, and/or maintenance of the equipment described.
  • Page 3: Table Of Contents

    COMMUNICATOR FORMAT SELECTIONS ..............................13 STANDARD (DEFAULT) ZONE TYPES................................18 AUXILIARY OUTPUT EVENT SELECTION ..............................22 NX-6 PROGRAMMING WORKSHEETS................................29 COMMUNICATOR CODES FOR SLOW SPEED FORMATS ONLY ......................33 APPENDIX 1 REPORTING FIXED CODES IN CONTACT ID AND SIA ......................37 APPENDIX 2 REPORTING ZONE CODES IN SIA OR CONTACT ID ......................
  • Page 4: General Description

    Up to 3 modules can be added to expand the capabilities of the NX-6. Warranty information is provided in the GE Security Product Catalog.
  • Page 5: Feature Definitions

    (Loc. 37 and 39, pg. 20) AC Power / Low Battery Sounder Alert If enabled, the NX-6 will beep the keypad sounder upon arming or disarming if the AC power is missing or a low battery has been detected. (Loc. 23, pg. 17) Arm / Disarm Codes The NX-6 can have 40 four-digit or six-digit codes to arm/disarm the control.
  • Page 6 During the time between trips, the NX-6 can be programmed to sound the keypad and/or the siren. The NX-6 can also be programmed to report an alarm after two or more trips on the same zone. (Loc. 37, 39, 40 and 110-149, pg.
  • Page 7 (Loc. 111-149, pg. 28) Immediate Restore By Zone The NX-6 can be programmed to send alarm and restore reports as soon as they occur, or wait until the siren time has expired. (Loc. 37, pg. 19) Internal Event Log Up to 185 events can be stored in memory along with the date and time of the event.
  • Page 8 Quick Arm Feature The NX-6 has a one button "Quick Arm" feature that can be used to arm the system by pressing the [Exit] key or the [Stay] key on the keypad. If closing reports are sent, the user code will be 98. (Loc. 23, pg. 17) Recent Closing If enabled, the NX-6 will send a "Recent Closing Report"...
  • Page 9 Mode@ will automatically exit after 15 minutes. (Loc. 41, pg. 21) Wireless Sensor Missing/Low Battery The NX-6 will send a report to the central station when a wireless sensor has detected a low battery or has not reported to the receiver. The "Service" LED will illuminate when either condition exists.
  • Page 10: Programming The Led Keypads

    PROGRAMMING THE LED KEYPADS This section describes how to program the address and partition of each keypad as well as the options that are available. The address of the keypad is important because this is how the panel supervises the keypads. The factory default for the Master code is [1]-[2]-[3]-[4] when using a 4-digit code or [1]-[2]-[3]-[4]-[5]-[6] for a 6-digit code.
  • Page 11 SET SYSTEM CLOCK Step 1 Enter [r]-[9]-[7]-[master code]. The "Service" LED will flash. Enter AHour Code@. This must be two digits, i.e. [hour 10's digit]-[hour 1's digit]. Step 2 Enter AMinutes Code@. This must be two digits, i.e. [minutes 10's digit]-[minutes 1's digit]. Step 3 CHANGING USER CODES Step 1...
  • Page 12: Programming The Control

    Since all modules connected to the NX-6 are programmed through the keypad, the module you are programming should be the first entry. To program the NX-6 Control Panel, enter [0]-[#]. The [0] is the module number of the control and the [#] is the entry key.
  • Page 13: Programming Examples

    PROGRAMMING EXAMPLE – Figure 1 (Numerical Data) Zone 1 LED = 1 Zone 2 LED = 2 Data = 9 Data = 66 Zone 4 LED = 8 Zone 7 LED = 64 To change data in a Pressing [#] will exit segment, enter the data a location without followed by [ ]...
  • Page 14: Loading Factory Defaults

    12 seconds, during which time the "Service" LED will illuminate. User codes will not be accepted during the enrolling process. If a speaker is attached to the NX-6, it will click at this time. If a siren or bell is attached to the NX-6, it will sound for about 1 second.
  • Page 15: Communicator Format Selections

    Phone #1. If a "2" is programmed in this segment, it will cause the NX-6 to make the dial attempts in increments of two. The first two attempts will be made to Phone #1, the next two attempts to Phone #2, then repeating until the total number of attempts designated in Segment 1 is completed.
  • Page 16 Phone #2. If a "2" is programmed in this segment, it will cause the NX-6 to make the dial attempts in increments of two. The first two attempts will be made to Phone #2, the next two attempts to Phone #1, then repeating until the total number of attempts designated in Segment 1 is completed.
  • Page 17 Programming a "1" in this segment will cause the NX-6 to stop trying to communicate after the assigned number of attempts have been made to Phone #3. If a "2" is programmed in this segment, it will cause the NX-6 to make the dial attempts in increments of two.
  • Page 18 LOCATION 19 DOWNLOAD ACCESS CODE 8 segments, numerical data Location 19 contains the eight-digit access code the NX-6 must receive from the downloading software before the panel will permit downloading to occur. The factory default code is 84800000. LOCATION 20...
  • Page 19 LOCATION 23 PARTITION 1 3 segments, feature selection FEATURE AND REPORT SELECTIONS Location 23 is used to enable certain features that can be accessed or are visible to the user from the keypad of the system. In addition, certain communicator reports are enabled in location 23. Each of these features can be enabled by partition.
  • Page 20: Standard (Default) Zone Types

    STANDARD (Default) ZONE TYPES Zones can be programmed to be one of twenty different zone types (configurations). Zone Types # 17 - 20 can be used for wireless or hardwired zones using European double EOL configuration. Table 1.1 lists the standard (default) zone types.
  • Page 21 NOTE: To null a zone, program the zone in APartition Select@ as zero (0) in all partitions and do not use end-of-line resistors. LOCATION 25 ZONE TYPE FOR ZONES 1-8 8 segments, numerical data Location 25 contains the zone type (configuration) for zones 1-8. Segment 1 is for zone 1, and Segment 8 is for zone 8. Default zone types are found in the Table 1.1 on page 18.
  • Page 22 â On if Fail To Communicate report enabled. Segment 4 ã On if Log Full report enabled. ä On if Autotest report enabled. å On if Start/End programming report enabled. æ On if End Download report enabled. ç On if Sensor Low Battery report enabled. è...
  • Page 23 Location 41, this code must contain six (6) digits. If this option is not enabled in location 41, the last 2 segments (digits) will be ignored. With the NX-6 disarmed, the "Go To Program Code" can be used to enter the Program Mode.
  • Page 24: Auxiliary Output Event Selection

    LOCATION 47 AUXILIARY OUTPUT #1, EVENT AND TIME 2 segments, numerical data Use Table 2.1 to select the event that will activate Auxiliary Output 1. Segment 1 Program the timing from 0-255 (minutes or seconds, depending on data programmed in Segment 2 Segment 1, Location 46).
  • Page 25 2 segments, numerical data Location 52 contains the time in 24 hour format the NX-6 enables codes designated as arm only after closing. This time is only valid on those days programmed in location 54. Note: Opening time must be earlier than closing time for Auto Arm, Auxiliary Outputs, or Code Authorization to function properly.
  • Page 26 SLOW FORMAT COMMUNICATOR CODES LOCATIONS 56- 83 ARE ONLY USED WHEN REPORTING EVENTS TO A PAGER OR USING A SLOW FORMAT SUCH AS 4+2. WHEN USING CONTACT ID OR SIA, THERE IS NO NEED TO PROGRAM THESE LOCATIONS. LOCATION 56 RESTORE 2 segments, numerical data Location 56 contains the event code for a zone "Restore"...
  • Page 27 LOCATION 65 KEYPAD PANIC 2 segments, numerical data Location 65 contains the tens and ones digits that will be sent for a 4+2 format if the keypad "Panic" is enabled in the partition feature selection Segment 1 contains the tens digit, segment 2 contains the ones digit. LOCATION 66 KEYPAD MULTIPLE CODE ENTRY (TAMPER) 2 segments, numerical data...
  • Page 28 LOCATION 76 LOG FULL 2 segments, numerical data Location 76 contains the tens and ones digits for a 4+2 format if the "Log Full Reporting" is enabled. Segment 1 contains the tens digit, segment 2 contains the ones digit. LOCATION 77 OPENING 2 segments, numerical data Location 77 contains the tens digit of a 4+2 format if the "Opening Reporting"...
  • Page 29 PARTITIONING CODES & FEATURES LOCATIONS 88-91 ARE FOR PROGRAMMING DIFFERENT ACCOUNT CODES AND/OR FEATURES FOR EACH PARTITION. IF A LOCATION IS NOT PROGRAMMED, THE FEATURE FOR PARTITION 1 AND ACCOUNT CODE FOR THE PHONE NUMBER WILL BE USED. LOCATION 88 ACCOUNT CODE FOR PARTITION 1 6 segments, numerical data Location 88 contains the account code sent when partition 1 is reported.
  • Page 30 CUSTOMIZING ZONE TYPES (Configuration Groups) LOCATIONS 110-149 ARE USED TO CHANGE THE ZONE TYPES AS LISTED IN THE TABLE ON PAGE 18. THESE LOCATIONS ARE CONSIDERED ADVANCED PROGRAMMING AND SHOULD ONLY BE CHANGED WITH A THOROUGH UNDERSTANDING OF THE OPERATION OF EACH BIT. LOCATION 110 ZONE TYPE 1 ALARM EVENT CODE 1 segment, numerical data...
  • Page 31: Nx-6 Programming Worksheets

    NX-6 PROGRAMMING WORKSHEETS (- Factory defaults for segments are in bold italics text. Some locations have been intentionally omitted. Attempts to access these reserved locations will cause the keypad to sound an error beep.) DESCRIPTION DEFAULT PROGRAMMING DATA PHONE #1...
  • Page 32 DESCRIPTION DEFAULT PROGRAMMING DATA PHONE #3, SELECT EVENTS TO REPORT TO PHONE #3 Segment #1 Segment # 2 1 - Alarms and Restores “ 1 - Tampers “ 2 - Open / Close “ 2 - Short Circuit “ 3 - Bypass “ 3 - Sensor Lost “...
  • Page 33 DESCRIPTION DEFAULT PROGRAMMING DATA ZONES 9-16, ZONE TYPES 6-6-6-6-6-6-6-6 __ __ __ __ __ __ __ __ ZONES 9-16, PARTITION SELECTION (Segment 1=Zone 9 thru Segment 8=Zone 16) Segment #1 Segment #3 Segment #5 Segment #7 1 - Partition #1 “ 1 - Partition #1 “...
  • Page 34 DESCRIPTION DEFAULT PROGRAMMING DATA KEYPAD SOUNDER CONTROL 1 - Keypad sounds for Telephone Line Cut when in the Armed state “ 2 - Keypad sounds for Telephone Line Cut when in the Disarmed state “ 3 - Keypad sounds upon AC Power Failure “ 4 - Keypad sounds upon Low Battery Detection “...
  • Page 35: Communicator Codes For Slow Speed Formats Only

    DESCRIPTION DEFAULT PROGRAMMING DATA AUXILIARY OUTPUT #2, EVENT & TIME Segment #1: Program the event number for output #2 1=Fire alarm Segment #2: Program the timing for output #2 10 seconds AUXILIARY OUTPUT #3, EVENT & TIME Segment #1: Program the event number for output #3 2= 24 Hour Alarm Segment #2: Program the timing for output #3 10 seconds...
  • Page 36 DESCRIPTION DEFAULT PROGRAMMING DATA SENSOR LOW BATTERY COMMUNICATOR CODE Segment #1: Partition #1 Sensor Low Battery Code Segment #2: Partition #2 Sensor Low Battery Code SENSOR MISSING COMMUNICATOR CODE Segment #1: Partition #1 Sensor Missing Code Segment #2: Partition #2 Sensor Missing Code DURESS __ __ AUXILIARY 1...
  • Page 37 DESCRIPTION DEFAULT PROGRAMMING DATA CUSTOMIZING ZONE TYPES (GROUPS) ZONE TYPE 1 ALARM EVENT CODE ZONE TYPE 1 CHARACTERISTIC SELECTION Segment #1 1 - Fire (enable for fire zone) “ 2 - 24 Hour (enable for non-fire 24 hour zone) “ 3 - Keyswitch zone “...
  • Page 38 DESCRIPTION DEFAULT PROGRAMMING DATA ZONE TYPE 12 CHARACTERISTIC SELECT 457-125-45678 _____ _____ _____ ZONE TYPE 13 ALARM EVENT CODE ____ ZONE TYPE 13 CHARACTERISTIC SELECT 0-12458-5678 _____ _____ _____ ZONE TYPE 14 ALARM EVENT CODE ____ ZONE TYPE 14 CHARACTERISTIC SELECT 5-12456-5678 _____ _____ _____ ZONE TYPE 15 ALARM EVENT CODE...
  • Page 39: Appendix 1 Reporting Fixed Codes In Contact Id And Sia

    APPENDIX 1 REPORTING FIXED CODES IN CONTACT ID AND SIA The table below lists the event codes sent for the following reports (if enabled) when using CONTACT ID or SIA formats. REPORT CONTACT ID MANUAL TEST AUTOTEST OPEN (user number) CLOSE (user number) CANCEL (user number) DOWNLOAD COMPLETE...
  • Page 40: Appendix 2 Reporting Zone Codes In Sia Or Contact Id

    APPENDIX 2 REPORTING ZONE CODES IN SIA OR CONTACT ID The NX-6 has the ability to report SIA level 1 transmissions to either or both phone numbers. Each report in SIA consists of an Event Code and a Zone or User ID. The Zone ID will be the zone number that is in alarm. The event code will come from the chart below and be programmed in the Zone Type event code.
  • Page 41: Appendix 3 Expander Numbers For Reporting Expander Trouble

    APPENDIX 3 EXPANDER NUMBERS FOR REPORTING EXPANDER TROUBLE The tables below list the device numbers that will be reported for trouble conditions. Device Device # reported NX-6 Control Panel See page 37 for possible report codes. NX-534E Two Way Listen In NX-540E NetworX AOperator@...
  • Page 42: Nx-6 Wiring Diagram

    NX-6 WIRING DIAGRAM Page 40...
  • Page 43: Terminal Description

    (NOTE: These numbers are for one keypad at the end of the wire. When connecting more than one device to the end of the wire, a higher gauge wire will be required.) WHEN CONNECTED TO NX-6 WHEN CONNECTED TO NX-320E...
  • Page 44: Board Installation

    BOARD INSTALLATION Inside the can, several 2-holed insertion points have been constructed. This allows for either vertical or horizontal placement of the modules. Notice that each insertion point has two sizes of holes B a larger hole and a smaller hole. Diagram 1: The black plastic PCB guides are grooved on one edge where the PC board will be seated.
  • Page 45: Regulatory Notices

    Product: NetworX operation of the equipment at the customers’ premises which Model Number: NX-6 remains connected to the telephone network, shall occur by Brand: CADDX reason of such withdrawal. R&TTE Directive:...
  • Page 46: Underwriters Laboratories Information

    Grade B & C Central Station Burglar Alarm Unit (UL1610) (CAN/ULC-S304-M88) Home Health Care Signaling (UL1637) When installing an NX-6 in compliance with Underwriters Laboratories, the following instructions must be observed: ! Initiating and indicating devices must be rated at 11.5 to 12.4 V DC residential, 12.0 V DC commercial.
  • Page 48: Specifications

    11.25" Wide 11.25" High 3.50" Deep SHIPPING WEIGHT 9 lbs. Main 800-727-2339 Technical Support 888-437-3287 Outside the US 903-845-6941 Sales & Literature 800-547-2556 Main Fax 903-845-6811 Web: www.gesecurity.com UL approved for ANSI/SIA NX-6 INSTALLATION MANUAL CP-01-2000 NX6IP05 REV. P (FEB 2005)